60510
4
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
PAL
HR-XV28S
EN
LPT1058-001A
DVD PLAYER &
VIDEO CASSETTE RECORDER
INSTRUCTIONS
VJ9033CP1Z_E-EK.book Page 1 Friday, March 11, 2005 9:53 AM
2
Safety Precautions
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference, should the unit
require maintenance, contact an authorized service location see
service procedure.
Use of controls, adjustments or the performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
To prevent direct exposure to laser beam, do not try to open the
enclosure. Visible laser radiation when open. DO NOT STARE
INTO BEAM.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS DEFEATED.
CAUTION: The apparatus shall not be exposed to water,
dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
VIDEO Plus+ and PlusCode are registered trademarks of
Gemstar Development Corporation. The VIDEO Plus+ system
is manufactured under license from Gemstar Development
Corporation.
Notes on copyrights:
It is forbidden by law to copy, broadcast, show, broadcast via
cable, play in public, or rent copyright material without
permission.
This product features the copy protection function developed by
Macrovision. Copy protection signals are recorded on some
discs.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIALNUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and retain
this guide as a permanent record of your purchase.
CAUTION: When you are not using the unit for a long period of
time, it is recommended that you disconnect the power cord
from the mains outlet.
The STANDBY/ON Í/I button does not completely shut off
mains power from the unit, but switches operating current on
and off. “Í” shows electrical power standby and “I” shows ON.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOTREMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation mark within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
This product is manufactured to comply with the
radio interference requirements of EEC
DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/
EEC.
Model No.
Serial No.
Important notes on controlling
this unit
This unit uses one set of controls to operate both DVD
and VCR. The following buttons are helpful in
successfully controlling each part.
1. Í/I Button
Press the Í/I button on the remote control or front
panel to turn on this unit.
2. DVD Button
Press DVD button on the remote control when you
want to control the DVD.
The DVD indicator will light on the front panel
display to show that the DVD is selected.
3. VCR Button
Press the VCR button on the remote control when
you want to control the VCR.
The VCR indicator will light on the front panel
display to show that the VCR is selected.
4. DVD/VCR Button
Press the DVD/VCR button on the front panel to
toggle control between the DVD and the VCR.
VJ9033CP1Z_E-EK.book Page 2 Friday, March 11, 2005 9:53 AM
3
INTRODUCTION
Table of Contents
Introduction
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important notes on controlling this unit . . . . . . . . . 2
Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About the symbols for instructions . . . . . . . . . . . . . 3
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Remote Control Operation Range . . . . . . . . . . . . . 4
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Selecting the Viewing Source . . . . . . . . . . . . . . . . 5
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Display Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting to Optional Equipment. . . . . . . . . . . . 11
Before Operation-VCR part . . . . . . . . . . . . . . . . .12-16
Tuning in a video channel on your TV . . . . . . . . . 12
Initial preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the clock Manually . . . . . . . . . . . . . . . . . . 13
To set the colour system . . . . . . . . . . . . . . . . . . . 13
How to use the main menu . . . . . . . . . . . . . . . . . 14
Tuning in TV Stations Automatically . . . . . . . . . . 14
Tuning in TV Stations Manually . . . . . . . . . . . . . . 15
Changing the order of TV Stations
. . . . . . . . . . . . . . 16
Deleting TV Stations . . . . . . . . . . . . . . . . . . . . . . 16
Before Operation-DVD part . . . . . . . . . . . . . . . . .17-19
General Operation . . . . . . . . . . . . . . . . . . . . . . . . 17
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Menu Language. . . . . . . . . . . . . . . . . . . . . . . 17
Disc Audio / Subtitle / Menu. . . . . . . . . . . . . . 17
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TV Aspect . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . 17
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Dolby Digital / DTS / MPEG. . . . . . . . . . . . . . 18
Sample Freq. (Frequency). . . . . . . . . . . . . . . 18
DRC (Dynamic Range Control) . . . . . . . . . . . 18
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Auto Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LOCK (Parental Control) . . . . . . . . . . . . . . . . . . . 19
Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Password (Security Code) . . . . . . . . . . . . . . . 19
Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operation
Operation with tape . . . . . . . . . . . . . . . . . . . . . . .20-24
Playing a tape . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
CM (Commercial Message) Skip. . . . . . . . . . 20
OPR (Optimum Picture Response) . . . . . . . . 20
Instant Timer Recording . . . . . . . . . . . . . . . . . . . 21
VIDEO Plus+ Programming . . . . . . . . . . . . . . . . . 22
Timer recording using On Screen Display . . . .23-24
Additional Operation - VCR part . . . . . . . . . . . . .25-27
Hi-Fi Stereo Sound System (NIC) . . . . . . . . . . . . 25
On Screen Display (F.OSD) . . . . . . . . . . . . . . . . 25
Tape Counter Memory Stop . . . . . . . . . . . . . . . . 25
Video Doctor (Self-Diagnosis) . . . . . . . . . . . . . . . 26
Wide Screen Compatibility 16:9 . . . . . . . . . . . . . 26
To set the decoder . . . . . . . . . . . . . . . . . . . . . . . .26
Recording from External Components. . . . . . . . . .27
Copying from DVD to VCR . . . . . . . . . . . . . . . . . .27
Operation with DVD and Video CD . . . . . . . . . . 28-30
Playback Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .28
General Features . . . . . . . . . . . . . . . . . . . . . . . . .28
Moving to another TITLE . . . . . . . . . . . . . . . .28
Moving to another CHAPTER / TRACK . . . . .28
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . .28
Still Picture and Frame-by-Frame Playback . .29
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . .29
Marker Search . . . . . . . . . . . . . . . . . . . . . . . .29
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Changing the Audio Channel . . . . . . . . . . . . .30
Last Scene Memory . . . . . . . . . . . . . . . . . . . .30
Instant Replay . . . . . . . . . . . . . . . . . . . . . . . . .30
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . .30
Special DVD Features . . . . . . . . . . . . . . . . . . . . .30
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Disc Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Camera Angle. . . . . . . . . . . . . . . . . . . . . . . . .30
Changing the Audio Language . . . . . . . . . . . .30
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Operation with Audio CD and MP3 Disc . . . . . . . . .31
On-Screen Display - DVD . . . . . . . . . . . . . . . . . . .31
Maintenance and Service . . . . . . . . . . . . . . . . . . .31
Playing an Audio CD or MP3 Disc . . . . . . . . . . . 32-34
Audio CD and MP3 Disc Features . . . . . . . . . . . .33
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Moving to another Track . . . . . . . . . . . . . . . . .33
Repeat Track / All / Off . . . . . . . . . . . . . . . . . .33
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Programmed Playback . . . . . . . . . . . . . . . . . . . . .34
Repeat Programmed Tracks . . . . . . . . . . . . . .34
Erasing a Track from “Program” List . . . . . . . .34
Erasing the Complete Program List . . . . . . . .34
Viewing a JPEG Disc. . . . . . . . . . . . . . . . . . . . . . . . .35
Slide Show. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Still Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Moving to another File . . . . . . . . . . . . . . . . . . . . . .35
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
To rotate picture. . . . . . . . . . . . . . . . . . . . . . . . . . .35
Reference
Language and Area Code List . . . . . . . . . . . . . . . . .36
Language Code List. . . . . . . . . . . . . . . . . . . . . . . .36
Area Code List. . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 37-38
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Note: Indicates special operating features of this unit.
Tip: Indicates tips and hints for making the task easier.
VJ9033CP1Z_E-EK.book Page 3 Monday, March 14, 2005 6:04 PM
4
Before Use
Playable Discs
Notes:
Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs cannot
be played on the unit.
Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
Do not use irregular shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
Notes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs may
be intentionally programmed by software manufacturers.
This unit plays DVDs and Video CDs according to disc
content designed by the software manufacturer,
therefore some playback features may not be available or
other functions may be added.
Regional code of the DVD player and DVDs
This DVD player is designed and manufactured for
playback of region “2” encoded DVD software.
The region code on the labels of some DVD
discs indicates which type of player can play
those discs. This unit can play only DVD discs
labeled “2” or “ALL”. If you try to play any
other discs, the message “Check Regional Code” will
appear on the TV screen. Some DVD discs may not have
a region code label even though their playback is
prohibited by area limits.
Disc-related terms
Title (DVD only)
The main film content or accompanying feature content
or additional feature content, or music album. Each title
is assigned a title reference number enabling you to
locate it easily.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters.
Each chapter is assigned a chapter number, enable you
to locate the chapter you want. Depending on the disc,
chapters may not be recorded.
Track (Video CD and audio CD only)
Sections of a picture or a musical piece on a video CD or
an audio CD. Each track is assigned a track number,
enabling you to locate the track you want.
Scene
On a video CD with PBC (Playback control) functions,
moving pictures and still pictures are divided into
sections called “Scenes”. Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want.
A scene is composed of one or several tracks.
Types of video CDs
There are two types of video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact
with the system via menus, search functions, or other
typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included in the
disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs
allow playback of video pictures as well as sound, but
they are not equipped with PBC.
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor
•Angle: About 30° in each direction of the front of the
remote sensor
Remote control battery installation
Detach the battery cover on the rear of the
remote control, and insert two (R03/AAA)
size batteries with + and - aligned
correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
DVD
(8 cm / 12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play SVCD, DVD±R/RW and
CD-R/RW that contains audio titles, MP3 or JPEG files.
2
AAA
AAA
VJ9033CP1Z_E-EK.book Page 4 Friday, March 11, 2005 9:53 AM
5
INTRODUCTION
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials come
in handy. For maximum protection, re-pack the unit as it
was originally packed at the factory.
When setting the unit
The picture and sound of a nearby TV or radio may be
distorted during playback. In this case, position the unit
away from the TV or radio, or turn off the unit after
removing the disc.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber of plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents, such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD player is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or worn
down, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not get
on the surface.
Do not stick paper or tape on the disc.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct
sunlight, as there may be a considerable temperature
increase inside the car.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture
quality and sound distortion. Before playing, clean the
disc with a clean cloth. Wipe the disc from the center out.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
About Symbols
About the symbol display
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not permitted by the DVD+VCR or is not
available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbol is
applicable only to the disc represented by the symbol.
DVD
Video CDs.
Audio CDs.
MP3 disc.
JPEG disc.
Notes:
If you insert a disc while the DVD+VCR is in the VCR
mode, the DVD+VCR will switch to DVD mode
automatically.
If you insert a cassette tape without prevention tab
while the DVD+VCR is in the DVD mode, the
DVD+VCR will switch to VCR mode automatically.
Selecting the Viewing Source
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
If you want to view DVD deck output source:
Press DVD until DVD indicator in the display window lights
and output source of DVD deck is viewed on the TV screen.
If you want to view VCR deck output source:
Press VCR until VCR indicator in the display window lights
and output source of VCR deck is viewed on the TV screen.
DVD
VCD
CD
MP3
JPEG
VJ9033CP1Z_E-EK.book Page 5 Friday, March 11, 2005 9:53 AM
6
Front Panel
Disc Tray (DVD deck)
Insert a disc here.
Cassette Compartment (VCR deck)
Insert a video cassette here.
Remote Sensor
Point the DVD+VCR remote control here.
Display Windows
< OPEN/CLOSE
Opens or closes the disc tray.
;
Pause playback or recording. Press
repeatedly for frame-by-frame playback.
5
- DVD: Skip to next chapter or track. Press and hold for two
seconds for a fast forward search.
- VCR: Advances the tape during the STOP mode or for fast
forward picture search.
1
Starts playback of a disc or tape.
6
- DVD: Skip to beginning of current chapter or track, press twice in quick
successions to go to previous chapter or track. Press and hold button for
about two seconds to search backward.
- VCR: Rewinds the tape during the stop mode or for fast reverse picture
search.
¥
To record normally or to activate
One-touch Timer Recording by
repeated presses.
VCR/DVD
Select one of your output sources to view on the TV
screen between DVD and VCR.
Stops playback of the disc or tape.
< EJECT
Ejects the tape in the VCR deck.
PROG. (-/+)
To scan up or down through memorized channels.
Í/I
Switches the DVD+VCR ON and STANDBY.
Video IN Jack
Audio IN (L/R) Jacks
VJ9033CP1Z_E-EK.book Page 6 Friday, March 11, 2005 9:53 AM
7
INTRODUCTION
Display Window
The DVD deck is selected.
Lights when TV mode is active.
DVD+VCR is Recording.
(VCR part only)
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
Indicates repeat mode.
DVD+VCR is in timer recording or a timer
recording is programmed. (VCR part only)
A cassette is in the VCR deck.
The VCR deck is selected.
Indicates total playing time, elapsed time, remaining time or
current deck status (Playback, Pause, etc).
VJ9033CP1Z_E-EK.book Page 7 Friday, March 11, 2005 9:53 AM
8
Remote Control
OPEN/CLOSE, EJECT (<)
- Ejects the tape in the VCR deck.
- Opens and closes the disc tray.
AUX
Select input source for recording into
tape.
DISC MENU
Accesses menu on a DVD disc.
SKIP (:/9)
Skip to beginning of current chapter or
track, press twice in quick successions
to go to previous chapter or track.
Skip to next chapter or track.
RETURN
- Removes the setup menu.
- Displays the menu of a video CD with
PBC.
Stops playback or recording.
MNL. PROG.
Places a track on the program list.
CLEAR ( )
Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
• A.MONITOR
Selects an audio language (DVD) or an
audio channel (VCD).
• SUBTITLE
Selects a subtitle language.
• ANGLE
Selects a DVD camera angle, if
available.
• ZOOM
Enlarges DVD video image.
• MARKER
Marks any point during playback.
• SEARCH
Displays Marker Search menu.
• TITLE
Displays the disc’s Title menu, if
available.
• REC (¥)
Records normally or activates One
touch Timer Recording with repeated
presses.
Note:
This remote control uses the same buttons for VCR and
DVD functions (ex. PLAY).
When using a VCR, first press the VCR button.
When using a DVD, first press the DVD button.
Í
/I
Switches DVD+VCR ON and STANDBY
.
TV/VCR •
To view channels selected by the VCR
tuner or by the TV tuner.
DVD
Select the DVD+VCR function mode to
DVD.
VCR •
Select the DVD+VCR function mode to
VCR.
DISPLAY
- - : - -
- Accesses On-Screen Display (DVD).
- Shows you the current time or counter
(VCR).
2/1/3/4
- Selects menu options.
- PR/TRK (+/-): Selects VCR channels.
Adjusts manually the tape’s picture on
the screen.
SETUP/MENU (i)
Accesses or removes DVD Setup
menu and VCR menu.
ENTER/OK
Confirms menu selections. Displays
functions on the TV screen.
;
- Pause playback or recording.
- Press repeatedly for frame-by-frame
playback.
(6) •
- For fast reverse picture search.
- Rewinds the tape during the STOP
mode.
1
Starts playback.
(5) •
- For fast forward picture search.
- Advances the tape during the STOP
mode.
0-9 numerical buttons
Selects numbered options in a menu.
REPEAT •
Repeat chapter, track, title or all.
RANDOM ( ) •
- Plays tracks in random order.
- CM SKIP
REPEAT A-B •
Repeats sequence between two points
(A and B)
Selects recording speed.
VIDEO Plus+ •
To display the programme menu for
VIDEO Plus+ programming.
VJ9033CP1Z_E-EK.book Page 8 Friday, March 11, 2005 9:53 AM
9
INTRODUCTION
Rear Panel
Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
AERIAL
Connect the aerial using this jack.
AC Power Cord
Connect to a power source.
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
AUDIO OUT (Left/Right) (DVD EXCLUSIVE OUT)
Connect to an amplifier, receiver or stereo system.
EURO AV2 DECODER (VCR IN+OUT/DVD OUT)
Connect to pay-TV decoder, Set Top Box or another
video recorder.
EURO AV1 AUDIO/VIDEO (VCR IN+OUT/DVD OUT)
Connect to your TV set or another video recorder.
COAXIAL (DVD EXCLUSIVE OUT)
(Digital audio out jack)
Connect to digital (coaxial) audio equipment.
RF.OUT
Connect to your TV using this jack.
VJ9033CP1Z_E-EK.book Page 9 Friday, March 11, 2005 9:53 AM
10
Connections
Tips:
Depending on your TV and other equipment there are
various ways you can connect the player.
Please refer to the manuals of your TV, VCR, stereo
system or other devices as necessary for additional
connection information.
Notes:
The picture and sound of a nearby TV, VCR, or radio may be
distorted during playback. Position the units away from each
other or turn off the unit after removing the disc.
Make sure the DVD+VCR is connected directly to the TV and
tune the TV to the correct video input channel.
Do not connect the DVD+VCR’s AUDIO OUT jack to the
phono in jack (record deck) of your audio system. Do not
connect the DVD+VCR via another VCR. The DVD image
could be distorted by the copy protection system.
Connecting to a TV
Make one of the following connections, depending on the
capabilities of your existing equipment.
Basic connection (AV)
1. Connect the EURO AV1 AUDIO/VIDEO on the rear
panel of this unit to the SCART input socket on the
TV using a SCART lead (not supplied).
For TV without SCART, connect the yellow VIDEO
OUT jack and DVD/VCR AUDIO OUT jacks of this
unit to the TV.
2. Some TV broadcasters transmit encoded television
signals which you can only see with a purchased or
rented decoder. You can connect such a decoder
(descrambler) to this unit.
Basic connection (RF)
1. Connect the RF antenna cable from your indoor/
outdoor antenna to AERIAL jack on the rear panel of
this unit.
2. Connect the supplied RF antenna cable from the
RF.OUT jack on the rear panel of this unit to your
television’s Antenna Input.
VIDEO INAERIAL
AUDIO INPUT
L
R
SCART INPUT
Rear of TV
Satellite or Set Top Box
Rear of this unit (Basic connection)
VJ9033CP1Z_E-EK.book Page 10 Friday, March 11, 2005 9:53 AM
11
PREPARATION
Connections (Continued)
Connecting to Optional
Equipment
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Pro Logic II/Pro
Logic
Connect the Left and Right DVD/VCR AUDIO OUT or
AUDIO OUT (DVD EXCLUSIVE OUT) jacks on this unit
to the audio left and right in jacks on your amplifier,
receiver or stereo system, using the audio cables.
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/
Video receiver equipped with a multi-channel
decoder (Dolby Digital™, MPEG 2 or DTS)
1. Connect one of this unit’s DIGITAL AUDIO OUT jack
(COAXIAL) to the corresponding in jack on your
amplifier. Use an optional digital (coaxial) audio
cable.
2. You will need to activate this unit’s digital output.
(See “AUDIO” on page 18).
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel Audio/
Video receiver that supports one or more of the audio
formats supported by your unit (MPEG 2, Dolby Digital
and DTS). Check the receiver manual and the logos on
the front of the receiver.
Warning:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
Notes:
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
Six Channel Digital Surround Sound via digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
To see the audio format of the current DVD in the On-
Screen Display, press A.MONITOR.
L
R
AUDIO INPUT
DIGITAL INPUT
COAXIAL
2 channel analog stereo or Dolby Surround connection.
Rear of this unit
Amplifier (Receiver)
Digital multi-channel
connection
DVD exclusive out
VJ9033CP1Z_E-EK.book Page 11 Friday, March 11, 2005 9:53 AM
12
Before Operation-VCR part
Tuning in a video channel on your TV
Notes:
The output frequency of this DVD+VCR is set at UHF
channel 36. If channel 36 is already used by another
TV station, or if the picture is distorted, you can
change the transmitter channel of your DVD+VCR.
Stages 5 ~ 8 will show you how to change the output
frequency of your DVD+VCR.
Your TV receives signals from the DVD+VCR like
another TV station. You have to select a channel
number on your TV and tune it in so that you may
watch video tapes. If you have used a SCART then
your TV should already have a dedicated video
channel built into it, usually called AV.
1. Make sure that you have correctly installed your
DVD+VCR as described earlier in this book.
Press Í/I to turn on your DVD+VCR.
Turn on your TV.
2. Insert a pre-recorded video tape into your DVD+VCR
and press
1
on the remote control.
Select a TV channel which you wish to watch video.
Don’t worry if you don’t have a video-tape to play at
this stage! If you switch your DVD+VCR on and
continue stages 3 ~ 4, instead of seeing video
playback tune your TV until you see a bright blue
screen.
3. Tune this channel until the video picture is sharp and
the sound is clear.
If you have used a SCART or AUDIO and VIDEO
cables you will not have to tune your TV, simply
select the AV channel. The AV channel is already
pre-tuned for optimum video playback on your TV.
4. Store this channel on your TV.
You will need to look at the TV instruction book if you
do not know how to do this.
5. Only carry out stages 5 ~ 8 if you cannot obtain
clear video playback as described in stages 1 ~
4.
Select a TV channel which you wish to watch video.
Make sure that your DVD+VCR is in standby
pressing Í/I on the remote control (only the clock
will be displayed).
6. Press PROG. (+/-) on the front of your DVD+VCR for
more than 4 seconds.
RF36 will appear in the display window.
The following picture will be displayed on the TV
screen.
7. Use PROG. (+/-) to select another video channel.
You may select any channel number between 22 and
68.
8. Select a TV channel which you wish to watch video.
Press Í/I on the front of your DVD+VCR when you
have finished.
Tune this channel so that a bright blue screen
appears.
Store this channel on your TV.
Notes:
Make sure that you have correctly installed your DVD+VCR and
successfully tuned in a dedicated video channel on your TV. If
you do not tune in a dedicated video channel on your TV you will
be unable to view and record video tapes!
Initial preset
For the following steps we do assume that you have just
connected your video recorder for the very first time. In
this case the video recorder is on after mains connection.
You should not touch any buttons yet. On the connected
TV you will now see.
Note:
If this menu does not appear, your video recorder was
programmed already.
1. If you have a satellite receiver, make sure that it is
connected to your VCR, switched on and Sky News
has been selected.
2. Press ENTER/OK to start the automatic storing of
the channels of the TV stations in your area.
3. The TV STATION TABLE will appear when tuning is
completed.
Press i to save your settings.
i
RF CHANNEL 36
P
SET
R
ACMS
OK
i
Pr-12
ACMS
ES
i
Pr-12
ACMS
VJ9033CP1Z_E-EK.book Page 12 Friday, March 11, 2005 9:53 AM
13
Before Operation-VCR part
PREPARATION
Setting the clock Manually
The clock in your DVD+VCR controls time and date
settings for your DVD+VCR.
1. Press i.
Press 2 or 1 to select SET.
Press ENTER/OK.
The auto adjust mode can be set to “OFF” by
pressing ENTER/OK if you want to set the time
manually.
2. Use the 3 or 4 on the remote control to alter the
HOURS, MINUTES, DAY, MONTH and YEAR.
Please note your DVD+VCR uses a 24 hour clock.
e.g. 1pm will be displayed as 13:00.
The day of the week will appear automatically when
you enter the year.
3. If you make a mistake press 2 or 1 and enter the
correct details.
4. Press i to return to a TV picture.
To set the colour system
1. Press i.
2. The main menu will appear on the TV screen.
3. Press 2 or 1 to select the SYS and press ENTER/
OK.
4. Press 3 or 4 to select according to the COLOUR
system used.
5. Press 2 or 1 to select the RF AUDIO.
Press 3 or 4 to select according to the RF AUDIO
used.
6. Press i to remove the menus from the TV screen.
HH MN DD MM YY
:..- -
- -
- - - -
- - - - -
i
12
SET
HH MN DD MM YY
:..00 1 01 05 SAT 8
i
12
SET
SYS
12
SET
OSD
ON
OFF
OSD
f
i
AUTO
PA L
MESECAM
SYS
SYS
12
SET
OSD
ON
OFF
OSD
f
i
SYS
RF-I/I
RF-B/G
RF-D/K
VJ9033CP1Z_E-EK.book Page 13 Friday, March 11, 2005 9:53 AM
14
Before Operation-VCR part
How to use the main menu
This DVD+VCR can easily be programmed by
using the menus displayed on screen.
The menus are controlled by the Remote Control
Handset.
1. Switch on your TV set and DVD+VCR by pressing
the Í/I button.
2. Press i button.
The main menu will appear on the TV screen.
•REC - Timer recording setting (see p. 23).
PR SET - Manual tuning setting (see p. 15).
•ACMS - ACMS (Automatic Channel Memory
System) (see p. 14).
SET - Date & clock setting (see p. 13).
SYS - To set the Colour TV System (see p. 13).
(Dr.) - To check a problem with your VCR (see
p. 26).
F.OSD ON/OFF - To display the operational mode
of your VCR (see p. 25).
(16:9/4:3) - To select the aspect ratio of your
TV (see p. 26).
DECODER - To use a pay-TV decoder (or
Satellite) with your VCR (see p. 26).
(OPR) - To improve the playback picture (see p.
20).
Appear when playback only.
NIC - To activate or deactivate the NICAM digital
sound (see p. 25).
Tip:
You can change the menu language on the DVD setup
menu. (See the Menu Language on page 17.)
3. Press 2 and 1 to select the desired menu.
Press ENTER/OK and use 3 or 4 to select.
4. Press i to return to a TV picture.
Tuning in TV Stations
Automatically
If the TV broadcast signal is weak your DVD+VCR
may not detect the necessary information and will
not be able to store them correctly. To overcome
this problem please turn to the MANUAL TUNING
section on page 15.
1. Press Í/I to turn on your DVD+VCR.
2. Press i button.
The main menu will appear on the TV screen.
Press 2 or 1 to select the ACMS.
Press ENTER/OK.
3. If you have a satellite receiver, make sure that it is
connected to your VCR, switched on and Sky News
has been selected.
4. Press ENTER/OK to start the automatic storing of
the channels of the TV stations in your area.
5. The TV STATION TABLE will appear when tuning is
completed.
Press i to save your settings.
Notes:
The DVD+VCR’s clock will be set automatically when
automatic tuning has finished. If the clock is wrong
please see “Setting the clock Manually” on page 13.
SYS
12
SET
OSD
ON
OFF
OSD
f
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
ACMS
Pr-12
OK
i
ACMS
OK
i
Pr-12
ACMS
02 C02 00 - - - - -
03 C03 00 - - - - -
04 - - - - - - - - -
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 - - - - -
OK
i
,DELETE :
MOVE :
P
SET
R
VJ9033CP1Z_E-EK.book Page 14 Friday, March 11, 2005 9:53 AM
15
Before Operation-VCR part
PREPARATION
Tuning in TV Stations Manually
In certain areas of the country broadcast signals
may be too weak for your DVD+VCR’s automatic
tuning process to find or assign TV stations
correctly.
You must tune in these weaker broadcast stations
manually in order for your DVD+VCR to store them.
1. Press i.
The main menu will appear on the TV screen.
Press 2 or 1 to select the PR SET.
Press OK.
2. Press i.
The station table will appear.
3. Press 3 or 4 to select the programme number that
you want to tune (for example, PR 04).
4. Press OK.
Press AUX to select C (Standard stations) or S
(Cable stations):
C02 - C69, S01 - S41.
Enter the channel number of station that you want to
tune, use 3 or 4 to find the required station.
5. Searching will stop when it locates a stations.
Press 1 to select MFT.
Control the fine tuning of the station by using 3 or
4.
6. Press 1 to select STATION so that you may name
your TV station.
Press OK.
7. Use 3 or 4 to select letters and numbers for the
station name.
Use 2 or 1 to move back and forth between
characters.
Press OK.
8. Press i, confirm the station placement.
If you wish to manually tune other stations repeat
stages 3 - 8.
9. Press i again.
Your new TV station has now been tuned into your
DVD+VCR.
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
P
SET
R
PR CH MFT STATION
01 00
CHANNEL/CABLE : AV
C03
P
SET
R
i
PR-03
02 C02 00 - - - - -
03 C03 00 - - - - -
04 - - - - - - - - -
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 - - - - -
OK
i
,DELETE :
MOVE :
P
SET
R
PR CH STATION
04 - - - - - -
MFT
P
SET
R
C - -
i
CHANNEL/CABLE : AV
PR CH STATION
04 00
C04
MFT
CHANNEL/CABLE : AV
i
P
SET
R
i
PR CH MFT
04 00C04
i
OK
STATION
P
SET
R
-
PR CH MFT
STATION
04 00
C04
PR-04
i
OK
P
SET
R
02 C02 00 PR-02
03 C03 00 PR-03
04 C04 00 PR-04
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-00
OK
i
,DELETE :
MOVE :
P
SET
R
VJ9033CP1Z_E-EK.book Page 15 Friday, March 11, 2005 9:53 AM
16
Before Operation-VCR part
Changing the order of TV Stations
After tuning TV stations into your DVD+VCR you
may wish to change the order in which they are
stored without having to retune them again. The
instructions given on this page will show you how
you can simply move them into your desired order.
1. Press i.
The main menu will appear on the TV screen.
Press 2 or 1 to select the PR SET.
Press ENTER/OK.
2. Press i.
Press 3 or 4 to select the programme number
you want to move (for example, PR-03).
Press 1.
3. Press 3 or 4 to select the programme number
you want to move to (for example, PR-05).
4. Press ENTER/OK.
The selected programme will be moved to the new
programme number.
If you wish to move other TV stations repeat stages
1 - 4.
5. Press i to remove the menus from the TV screen.
Deleting TV Stations
After tuning TV stations into your DVD+VCR you
may wish to delete a station.
The instructions given on this page will show you
how you can easily delete any unwanted TV
stations.
1. Press i.
The main menu will appear on the TV screen.
Use 2 or 1 to select the PR SET.
Press ENTER/OK.
2. Press i.
3. Press 3 or 4 to select the programme number
you want to delete. (for example, PR-00)
4. Press 2.
After a short while, the selected station will be
deleted.
If you wish to delete other TV stations repeat stages
3 - 4.
5. Press i to remove the menus from the TV screen.
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
P
SET
R
PR CH MFT STATION
01 00 PR-03
CHANNEL/CABLE : AV
C03
i
P
SET
R
02 C02 00 PR-02
03 C03 00 PR-03
04 C04 00 PR-04
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-00
OK
i
,DELETE :
MOVE :
P
SET
R
02 C02 00 PR-02
03 C03 00 PR-03
04 C04 00 PR-04
05 - - - - - - - - -
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-00
P
SET
R
OK
i
02 C02 00 PR-02
03 C04 00 PR-04
04 - - - - - - - - -
05 C03 00 PR-03
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-00
P
SET
R
OK
i
02 C02 00 PR-02
03 C04 00 PR-04
04 - - - - - - - - -
05 C03 00 PR-03
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-00
P
SET
R
OK
i
,DELETE :
MOVE :
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
P
SET
R
PR CH MFT STATION
01 00 PR-03
CHANNEL/CABLE : AV
C03
i
P
SET
R
02 C02 00 PR-02
03 C04 00 PR-04
04 - - - - - - - - -
05 C03 00 PR-03
06 - - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-00
P
SET
R
OK
i
,DELETE :
MOVE :
02 C02 00 PR-04
03 - - - - - - - - -
04 C03 00 PR-03
05
06 - - - - - - - - -
- - - - - - - - -
07 - - - - - - - - -
08 - - - - - - - - -
01 C01 00 PR-02
P
SET
R
OK
i
,DELETE :
MOVE :
VJ9033CP1Z_E-EK.book Page 16 Friday, March 11, 2005 9:53 AM
17
PREPARATION
Before Operation-DVD part
By using the DVD Setup menu, you can make various
adjustments to items such as picture and sound. You can
also set a language for the subtitles and the Setup menu,
among other things. For details on each Setup menu
item, see pages 17 to 19.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press 1 on the remote control.
To go back to the previous level:
Press 2 on the remote control.
General Operation
1. Press DVD on the remote control.
2. Press SETUP.
The Setup menu appears.
3. Use 3/4 to select the desired option then press 1
to move to the second level. The screen shows the
current setting for the selected item, as well as
alternate setting(s).
4. Use 3/4 to select the second desired option then
press 1 to move to the third level.
5. Use 3/4 to select the desired setting then press
ENTER/OK to confirm your selection. Some items
require additional steps.
6. Press SETUP or
1
exit the Setup menu.
LANGUAGE
Menu Language
Select a language for the VCR and DVD’s setup menu
and information display.
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track (disc
audio), subtitles, and the disc menu.
Original: Refers to the original language in which the
disc was recorded.
Other: To select another language, press number
buttons then ENTER/OK to enter the corresponding 4-
digit number according to the language code list in the
reference chapter (see page 36). If you enter the wrong
language code, press CLEAR ( ).
Off (for Disc Subtitle): Turn off Subtitle.
DISPLAY
TV Aspect
Display Mode
Display Mode setting works only when the TV Aspect
mode is set to “4:3”.
Letterbox: Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan: Automatically displays the wide picture on the
entire screen and cuts off the portions that do not fit.
4:3 : Select when a standard 4:3 TV is connected.
16:9 : Select when a 16:9 wide TV is connected.
Menu Language
Original
English
Off
Original
Disc Audio
Disc Subtitle
Disc Menu
Move
Select
LANGUAGE
DVD
DISPLAY
TV Aspect
Widescreen
16 : 9 Wide
Display Mode
Move
Select
DVD
DVD
VJ9033CP1Z_E-EK.book Page 17 Friday, March 11, 2005 9:53 AM
18
Before Operation-DVD part
AUDIO
Each DVD disc has a variety of audio output options.
Set this unit’s AUDIO options according to the type of
audio system you use.
Dolby Digital / DTS / MPEG
Bitstream: Select “Bitstream” if you connect the
DVD+VCR’s DIGITAL AUDIO OUT jack to an
amplifier or other equipment with a Dolby Digital,
DTS or MPEG decoder.
PCM (for Dolby Digital / MPEG): Select when
connected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital or MPEG will be
automatically downmixed to two-channel PCM
audio.
Off (for DTS): If you select “Off”, the DTS signal is
not output through the DIGITAL AUDIO OUT jack.
Sample Freq. (Frequency)
If your receiver or amplifier is NOT capable of handling
96 kHz signals, select 48 kHz. When this choice is made,
this unit automatically converts any 96 kHz signals to 48
kHz so your system can decode them.
If your receiver or amplifier is capable of handling 96 kHz
signals, select 96 kHz. When this choice is made, this
unit passes each type of signal through without any
further processing.
Check the documentation for your amplifier to verify its
capabilities.
DRC (Dynamic Range Control)
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic
presentation possible, thanks to digital audio technology.
However, you may wish to compress the dynamic range
of the audio output (the difference between the loudest
sounds and the quietest ones). This allows you to listen
to a movie at a lower volume without losing clarity of
sound. Set DRC to On for this effect.
OTHERS
The PBC and Auto Play settings can be changed.
PBC
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to the
PBC.
Off: Video CDs with PBC are played the same way as
Audio CDs.
Auto Play
You can set up the DVD+VCR so a DVD disc
automatically starts playing whenever the DVD is
inserted.
If Auto Play mode is set to On, this DVD player will search
for title that has the longest playback time and then play
back the title automatically.
On: Auto Play function is active.
Off: Auto Play function is not active.
Note:
The Auto Play function may not work for some DVDs.
Dolby Digital
Bitstream
PCM
48KHz
On
Bitstream
DTS
MPEG
Sample Freq.
DRC
Move
Select
AUDIO
DVD
DVD
DVD
PBC
Off
Move
Auto Play
OTHERS
On
Select
VCD
DVD
VJ9033CP1Z_E-EK.book Page 18 Monday, March 14, 2005 6:04 PM
19
Before Operation-DVD part
PREPARATION
LOCK (Parental Control)
Rating
Some movies contain scenes that may not be suitable for
children to view. Many of these discs contain parental
control information that applies to the complete disc or to
certain scenes on the disc. Movies and scenes are rated
from 1 to 8, depending on the area.
DVD video discs may or may not respond to the parental
control setting if the Area code of the disc is set wrongly.
Some discs offer more suitable scenes as an alternative.
Ratings are area dependent.
The parental control feature allows you to block access
to scenes below the rating you input, thereby preventing
your children from being able to view material you believe
is unsuitable.
1. Select “Rating” on the LOCK menu then press 1.
2. To access the Rating, Password and Area Code
features, you must input the 4-digit security code you
created.
If you have not yet entered a security code you are
prompted to do so. Input a 4-digit code and press
ENTER/OK. Enter it again and press ENTER/OK to
verify. If you make a mistake before pressing
ENTER/OK, press CLEAR ( ).
3. Select a rating from 1 to 8 using the 3/4 buttons.
1-8: Rating one (1) has the most restrictions and
rating eight (8) has the least restrictive.
Unlock: If you select unlock, parental control is not
active and the disc plays in full.
4. Press ENTER/OK to confirm your rating selection,
then press SETUP to exit the menu.
5. Press OPEN/CLOSE (<) to activate parental
control.
Note:
If you set a rating for the player, all disc scenes with the same
rating or lower are played. Higher rated scenes are not played
unless an alternate scene is available on the disc. The
alternative must have the same rating or a lower one. If no
suitable alternative is found, playback stops. You must enter the
4-digit password or change the rating level in order to play the
disc.
Password (Security Code)
You can enter or change password.
1. Select “Password” on the LOCK menu then press 1.
2. Follow step 2 as shown left column (Rating).
To change the password, select the “Change”, press
ENTER/OK and input the new 4-digit code then
press ENTER/OK. Input it again to verify.
3. Press SETUP to exit the menu.
If you forget your Security Code
If you forget your security code you can clear it using
the following steps:
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number “210499” and the
security code is cleared.
3. Enter a new code as described above.
Area Code
Enter the Area Code whose standards were used to rate
the DVD video disc, based on the list in the reference
chapter (see page 36).
1. Select “Area Code” on the LOCK menu then press
1.
2. Follow step 2 as shown left (Rating).
3. Select the first character using 3/4 buttons.
4. Press 1 and select the second character using 3/
4 buttons.
5. Press ENTER/OK to confirm your area code
selection.
LOCK
Rating
New
DG
Unlock
Password
Area Code
Move
Select
DVD
DVD
VJ9033CP1Z_E-EK.book Page 19 Friday, March 11, 2005 9:53 AM
20
Operation with tape
Playing a tape
You will only be able to load and eject video cassettes
when your DVD+VCR is plugged into the mains.
Your DVD+VCR may also playback recordings from
NTSC tapes (on PAL TV).
Getting a better picture
When a cassette is inserted and playback started,
the automatic tracking function works to get the
best possible picture automatically. If the quality of
the recording is poor, repeatedly press 3 or 4 on
the remote control to manually adjust the tracking
until any distortions have been removed.
1. Make sure that you have correctly connected your
DVD+VCR as described earlier in this book.
Turn on your TV.
Press Í/I to turn on your DVD+VCR.
Insert the video cassette into your DVD+VCR.
The video cassette should have the window side
facing up and the arrow facing away from you.
2. Press
1
to start playing your tape.
If you load a video cassette which has had its record
protection tab removed, playback of the cassette will
start automatically.
AUTO TRACKING
Your DVD+VCR will automatically adjust the tracking
to give the best picture quality.
If noise bars appear during playback, adjust the
tracking manually by pressing PR/TRK (+/-).
3. Press ; to still a picture.
Press
;
repeatedly to advance the tape frame by frame.
If you press 5, the picture will be slowed down at
about 1/19 times the normal playback.
Tapes can be paused for up to 5 minutes. After 5
minutes your DVD+VCR will stop the tape to prevent
damaging the tape or your DVD+VCR.
Still picture quality can be improved slightly by using
3 or 4.
4. Press
1
to continue playing your tape.
Double speed playback (SP mode only)
Press the “
1
(X2)” button during normal playback. The
tape will play back at double speed and without sound.
Press the “
1
(X2)” button to return to playback at
normal speed
Picture search:
During playing back press either 6 or 5 to this
will enable you to rapidly wind the tape (7 times
normal playback) see where you are on the tape.
Notes:
When playing back tapes that have been over-
recorded with new content, the original audio may be
audible during auto tracking.
The image may be distorted during special playback
in LP mode.
Logic search:
During fast forwarding or rewinding press and hold
6 or 5 the picture will be played back at 7 times
normal playback speed.
5. Slow motion playback,
Shuttle:
During playing back or still picture press 2 or 1.
You can reach the following playback speeds.
(-7xplay, -3xplay, -play, still, 1/19 slow, play, 2xplay,
7xplay)
To switch off the slow motion and shuttle, press the
desired function.
During slow motion and shuttle, the noise bars may
appear on the picture according to the status of tape.
If distortions can be seen in the picture, reduce them
with 3 or 4.
6. Press to end playback.
Press EJECT (<).
If the end of the tape is reached, your DVD+VCR will
stop playback automatically, rewind, stop, eject the
tape.
CM (Commercial Message) Skip:
This feature enables you during playback of a tape to
skip a commercial break in a few seconds, then resume
normal playback.
While tape is playing press on the remote control to
skip commercial (or another programme material).
Repeatedly press to skip:
1 Press 30 seconds
2 Press 60 seconds
3 Press 90 seconds
4 Press 120 seconds
5 Press 150 seconds
6 Press 180 seconds
OPR (Optimum Picture Response)
This feature automatically improves playback picture
quality by adjusting your DVD+VCR to the condition of
the tape. Please note that the OPR icon ( ) will only
appear in play that mode when playing a tape.
1. Press i.
2. Press 2 or 1 to select (OPR).
3. Press ENTER/OK.
4. Press 3 or 4 repeatedly to select: OFF, SOFT or
SHARP.
5. Press i return to screen.
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
R
P
SET
R
OFF
SOFT
SHARP
VJ9033CP1Z_E-EK.book Page 20 Friday, March 11, 2005 9:53 AM
21
Operation with tape
OPERATION
Instant Timer Recording
Your DVD+VCR allows you to make recordings
using a variety of simple methods:
Instant Timer Recording start recording
immediately for a set period of time or until the
video cassette runs out.
Your DVD+VCR incorporates Long Play (LP) which
enables you to record up to twice the amount of
time on a video cassette. For example an E-180 will
record up to 180 minutes using Standard Play (SP);
using LP you will be able to record up to 360
minutes. Please note there will be a slight loss in
picture and sound quality when using LP.
1. Make sure that you have correctly connected your
DVD+VCR as described earlier in this book.
Press Í/I to turn on your DVD+VCR.
2. Insert a video cassette with protection tab into your
DVD+VCR.
The video cassette should have the window side
facing up and the arrow facing away from you.
3. Press 3 or 4 to select the programme number
you wish to record.
You may also directly select programme number
using the numbered buttons on the remote control.
4. If you wish to record directly from the SCART or
RCA jacks, repeatedly press AUX until the socket
you wish to record from is displayed.
AV 1 for recording from EURO AV1 SCART jacks on
the rear of your unit.
AV 2 for recording from EURO AV2 SCART jacks on
the rear of your unit.
AV 3 for recording from VIDEO IN and AUDIO IN
(Left & Right) jacks on the front of your unit.
5. Press if you wish to record in Long Play or
Standard Play.
SP will produce improved picture and sound quality,
however LP will provide twice as much recording
time as SP.
6. Press REC (¥) on the remote to start recording.
Press ¥ on your unit or press REC (¥) on the
remote several times. Each successive press will
increase the record time by 30 minutes until you
reach a maximum of 9 hours.
7. Press ; to avoid recording unwanted scenes.
Press ; to continue recording.
Tapes can be paused for up to 5 minutes; RECP will
be displayed when a tape is paused. After 5 minutes
your DVD+VCR will stop recording to prevent
damaging the tape or your DVD+VCR.
8. Press to end recording.
Press EJECT (<).
Notes:
If you do not wish to record on a tape (this can happen
quite easily by accident!) remove the protection tab on
the back edge of the video cassette.
It is possible to record on a video cassette with the
record protection tab removed by covering the hole
with self adhesive tape.
Remember you can record one programme while
watching another by starting your instant recording,
press TV/VCR to select TV mode and then selecting a
different channel on your TV.
VJ9033CP1Z_E-EK.book Page 21 Friday, March 11, 2005 9:53 AM
22
Operation with tape
VIDEO Plus+ Programming
VIDEO Plus+ greatly simplifies entering the date,
channel, start and end times of a Timer Recording
by simply entering a VIDEO Plus+ Code. VIDEO
Plus+ Codes are published in most TV guide
magazines; they can vary one to nine numbers in
length.
VIDEO Plus+ and PlusCode are registered
trademarks of Gemstar Development Corporation.
The VIDEO Plus+ system is manufactured under
license from Gemstar Development Corporation.
1. Make sure that TV channels have been tuned and
stored in correct VIDEO Plus+ order.
Insert a video cassette with protection tab into your
DVD+VCR.
2. Press VIDEO Plus+.
3. Press the numbered buttons to enter the
PLUSCODE NO. of the TV programme that you wish
to record.
If you make a mistake press 2 then enter the
revised number.
4. Press ENTER/OK.
If PLEASE CHECK is displayed it means that you
have entered the wrong PLUSCODE number,
entered the PLUSCODE number incorrectly.
If “- -” is displayed, you have to enter the programme
number of the station, you want to record from.
5. Press 2 or 1 to select the settings that you wish to
revise. (PR, DATE, TIME and SP).
Press 3 or 4 to enter the correct information.
6. Press 1 to select the recording speed.
Press 3 or 4 to select the desired tape speed (SP,
IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program.
Check that the timer event details are correct.
If you wish to record from AUDIO IN and VIDEO IN
on the front or from either of the EURO SCART
sockets on the back of VCR, press AUX to select for
correct display (AV1, AV2 or AV3).
7. If you want to make another VIDEO Plus+ recording
repeat stages 2 - 7.
Press i twice.
If PLEASE CHECK is displayed, you have entered
incorrect information and will need to re-enter the
data.
Press Í/I to switch your DVD+VCR power off mode.
will appear in the video recorder’s display while
your VCR waits to make the recording.
To watch a DVD during timer recording standby
mode, press Í/I and DVD to switch to DVD mode.
8. Press Í/I to end recording.
OK
i
0~9,
PLUSCODE NO.
- - - - - - - - -
REC
OK
i
0~9,
246876543
REC
DELETE :
PLUSCODE NO.
PR DATE TIME
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
10
PR-01 12
SP
11 11 55~::
i
PR DATE TIME
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
10
PR-01 12
SP
11 11 55~::
i
PR DATE TIME
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - -
SP
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
10
PR-01 12
SP
11 11 55~::
i
VJ9033CP1Z_E-EK.book Page 22 Friday, March 11, 2005 9:53 AM
23
Operation with tape
OPERATION
Timer recording using On Screen
Display
You may set up to seven timer record events within
one month of the current date.
Note:
Before setting the timer make sure that you have
set the DVD+VCR clock correctly and you know
which stations you have tuned TV stations on your
DVD+VCR.
1. Insert a video cassette with protection tab into your
DVD+VCR.
The video cassette should have the window side
facing up and the arrow facing away from you.
2. Press i.
Press 2 or 1 to select REC.
Press ENTER/OK.
3. Press ENTER/OK to start setting the timer record
event.
4. Use the 3 or 4 to enter the station that you wish to
record then press 1.
Note:
If all timer record events are full press 3 or 4 to select
the event that you wish to remove and replace.
Press 2 to delete the event.
5. Use the 3 or 4 to enter the date of the programme.
If you press ENTER/OK before entering the date you
may select one of the following automated recording
features. Press 2 or 1 to select, then press
ENTER/OK to confirm.
DLY To record every day (except Saturday and
Sunday) at the same time.
SU~SA To record at the same time every week.
6. Use 3/4/2/1buttons to enter the recording start
and end times of the programme that you wish to
record.
Please note your DVD+VCR uses a 24 hour clock.
e.g. 1pm will be displayed as 13:00.
7. Press 1 to select the recording speed.
Press 3 or 4 to select the desired tape speed (SP,
IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program.
PR DATE
T I M E
- - - -
- -
SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- -
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
SP
i
OK
,
DELETE:
PR DATE
T I M E
- - - -
- -
SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
PR-03
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
SP
i
PR DATE
T I M E
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
PR-03 3
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
SP
i
OK
DLY SU MO TU WE TH FR SA
41400 1530~::
PR DATE
T I M E
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
PR-03
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
SP
i
41400 1530~::
PR DATE
T I M E
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
- - - - SP
PR-03
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
- - - - - - - -~::
i
SP
VJ9033CP1Z_E-EK.book Page 23 Friday, March 11, 2005 9:53 AM
24
Operation with tape
Timer recording using On Screen
Display (Continued)
8. Press i to set another timer record event and follow
steps 3 to 8.
Check that the timer event details are correct.
Press i return to screen.
If PLEASE CHECK is displayed, you have entered
incorrectly and will need to re-enter the data.
9. Press Í/I to switch your DVD+VCR to Timer
Standby mode.
The timer symbol ( ) will appear in the display
window while your DVD+VCR waits to make the
recording.
10. Press Í/I to end timer recording.
Notes:
The DVD+VCR will automatically power off when
Timer Recording ends.
During timer recording standby mode, the DVD and
VCR mode cannot be operated. To use the
DVD+VCR, press Í/I. After you use the DVD or VCR,
press Í/I again to put the VCR into timer recording
standby mode.
If at a later date you wish to delete or change any of
the settings in timer event memory you may do so
without having to enter all the timer event information
again. Simply display the timer event screen. Use 3
or 4 to select the event that you wish to delete or
change.
Press 2 to delete the event...or
Press ENTER/OK to change; then press 2 or 1 to
select; Station, Date, Start and End times and
recording speed. Press 3 or 4 to enter the correct
information.
If Timer record events Overlap...
Make sure that the preset times of the timer recording
events do not overlap. If they do, the earlier
programme will always be given priority.
Example:
Programme 1 is programmed to start at 16:00 and
end at 17:00.
Programme 2 is programmed to start at 16:30 and
end at 17:30.
(In this case, Programme 1 will be recorded in its
entirety, but only the last 30 minutes of Programme 2
will be recorded.)
To watch a DVD while performing a timer recording,
press TV/VCR to select VCR mode.
VJ9033CP1Z_E-EK.book Page 24 Friday, March 11, 2005 9:53 AM
25
OPERATION
Additional Operation - VCR part
Hi-Fi Stereo Sound System (NIC)
Your DVD+VCR will record and playback Hi-Fi stereo
sound. In addition it has a stereo NICAM digital stereo
sound decoder. This allows you to record and playback
the sound in several different ways. Video cassettes
recorded on your DVD+VCR will have a normal mono
audio track and two VHS Hi-Fi stereo audio tracks.
These stereo tracks allow you to make audio recordings
in Hi-Fi stereo or bilingual mode from a TV broadcast,
stereo audio system, video disc or another Hi-Fi VCR.
1. Your DVD+VCR’s NICAM digital sound decoder
allows you to enjoy broadcasts with NICAM sound,
as well as standard stereo, bilingual and mono
sound. The particular type of sound received or that
recorded will be briefly displayed on the TV screen
for a couple of seconds:
STEREO NICAM
Sound is automatically recorded on the Hi-Fi stereo
and mono tracks of the video tape.
BIL NICAM
Both audio channels will be recorded on the Hi-Fi
stereo tracks. The primary language channel (left)
will be recorded on the mono track of the video tape.
MONO
The sound is recorded on the Hi-Fi tracks and the
mono track of the video tape without any separation.
2. Press AUDIO repeatedly until the desired audio
mode appears.
3. The choice is STEREO, LEFT, RIGHT and MONO.
In BIL NICAM playback the primary language is
output on the left channel and the secondary
channel is output simultaneously from the right
channel when audio output is set to STEREO. The
primary language will be output from both channels
when the audio setting is MONO.
Please note that when adjusting the tracking control
Hi-Fi stereo sound may revert to MONO.
Note:
When OFF is selected in NIC, only mono sound will be
output.
On Screen Display (F.OSD)
You may easily display the current time or tape counter,
amount of tape left, day, month, year, day of week,
programme channel, tape speed and operational mode
of your DVD+VCR on the TV screen. If a recording is
taking place these On Screen Displays will not be
recorded onto the tape.
1. Press DISPLAY to display.
Press DISPLAY repeatedly to cycle through the
display options. The tape counter and amount of
tape left will appear if there is a tape loaded.
2. After 3 seconds the majority of the On Screen
Displays will clear leaving only the clock or tape
counter and the amount of tape left on the screen.
Press DISPLAY again to remove all displays from
the TV screen.
Note:
It cannot display when f.OSD is OFF.
Tape Counter Memory Stop
The Digital Tape Counter can be displayed on the
display window instead of the time by pressing
DISPLAY on the remote control. The Digital Tape
Counter indicates the relative positions of recordings on
the tape.
1. Press DISPLAY.
Press CLEAR ( ) to set the counter to 0:00:00.
Press
1
or start playback or recording.
The tape counter will display the actual play time in
hours, minutes and seconds.
2. Press when playback or recording is complete.
Press 6.
The tape will rewind and automatically stop when the
counter returns to 0:00:00.
Note:
To rewind to the beginning of the tape, press 6 again.
VJ9033CP1Z_E-EK.book Page 25 Friday, March 11, 2005 9:53 AM
26
Additional Operation - VCR part
Video Doctor (Self-Diagnosis)
This feature informs you that there is a problem with your
DVD+VCR. These error messages will appear on the TV
screen.
1. Press i.
Press 2 or 1 to select .
Press ENTER/OK.
2. Press 3 or 4 to check a problem.
ANTENNA CONNECT
PLEASE CHECK:
Connect the aerial into the jack securely.
HEAD STATUS
PLEASE CLEAN:
Clean your video heads.
TAPE STATUS
NOT RECORDABLE:
Insert a tape with its protection tab in place
NO. OF TIMER PROGRAMME
•2
Shows the number of timer recording.
NEXT TIMER PROGRAMME
PR-01 26 10:00~11:00 SP
Shows the current status of timer recording.
3. Press i to remove the menus from the TV screen.
Wide Screen Compatibility 16:9
Your DVD+VCR can record and play back wide screen
aspect ratio programmes (16:9). To record a wide screen
format programme successfully the correct type of wide
screen signal must be broadcast by the TV station.
1. Switch on your DVD+VCR.
Press i.
Press 2 or 1 to select .
Press ENTER/OK.
2. Press 3/4 repeatedly to select: AUTO, 4:3 or 16:9.
AUTO:
Automatically plays back Wide-Screen programmes
as Wide-Screen and Normal programmes as
normal.
4:3:
Only for playing back and recording Normal format
recordings (4:3).
16:9:
Only for playing back and recording Wide-Screen
format recordings (16:9).
3. Press i to remove the menus from the TV screen.
To enjoy Wide-Screen playback you must connect
your VCR to the TV using a SCART cable.
To set the decoder
We have already described, how to connect a decoder
for pay-TV station as DECODER or PREMIERE on page
10. For the recording of an encoded station you do not
have to control anything. You just select the station and
wait shortly until the decoding will start.
1. Press i.
The main menu will appear on the TV screen.
Press 2 or 1 to select the DECODER.
Press ENTER/OK.
2. Press 3 or 4 to select.
ON: When the decoder is connected to the AV2
socket.
OFF: When another VCR is connected to the AV2
socket.
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
i
ANTENNA CONNECT
PLEASE CHECK
HEAD STATUS
TAPE STATUS
NO. OF TIMER PROGRAMME
NEXT TIMER PROGRAMME
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
AUTO
4:3
16:9
i
SYS
12
SET
OSD
ON
OFF
OSD
f
ACMS
Pr-12
P
SET
R
AUTO
4:3
16:9
i
VJ9033CP1Z_E-EK.book Page 26 Friday, March 11, 2005 9:53 AM
27
Additional Operation - VCR part
OPERATION
Recording from External Components
You can record from an external component, such as a
camcorder or VCR, connected to any of the DVD+VCR’s
external inputs.
1. Make sure that the component you want to record
from is connected properly to the DVD+VCR.
2. Press AUX repeatedly to select the external input to
record from.
AV 1 for recording from EURO AV1 SCART jacks on
the rear of your unit.
AV 2 for recording from EURO AV2 SCART jacks on
the rear of your unit.
AV 3 for recording from VIDEO IN and AUDIO IN
(Left & Right) jacks on the front of your unit.
3. Load a recordable tape.
4. Set a recording mode (SP or LP) as necessary by
pressing repeatedly.
5. Play the tape or disc in the external component. If
you have a TV attached to your DVD+VCR, you can
see the video playing.
6. Press ¥ once to start recording.
The REC indicator lights in the display window.
7. Press to stop recording.
Notes:
Before recording, confirm the recording start position.
If your source is copy-protected using CopyGuard, you will
not be able to record it using this unit. See Copyright on page
2 for more details.
To record for a fixed length of time, see One-touch Timer
Recording.
Copying from DVD to VCR
You can copy the contents of a DVD to a VHS tape.
1. Insert the disc you wish to copy into the DVD deck
and close the disc tray.
2. Insert a blank VHS video tape into the VCR deck.
3. Find the place on the DVD from which you want to
start dubbing using the
1
, 6, 5 and ;
functions.
For best results, pause playback at the point from
which you want to record.
4. Press ¥ on the Remote Control. The DVD goes into
PLAY mode and the VCR goes into RECORD mode.
If the DVD disc menu appears, you may need to
press
1
manually to begin copying.
5. When the DVD is finished playing, press to end
copying.
Notes:
If the DVD you are attempting to copy is copy protected, you
will not be able to copy the disc. It is not permitted to copy
Macrovision encoded DVDs (or Discs). “LOCK” is displayed
in the display window.
You must stop the copy process manually when the DVD
movie ends, or the unit may replay and record over and over
again.
When you stop the DVD playback during copying, the
recording on VCR is stopped automatically.
VJ9033CP1Z_E-EK.book Page 27 Friday, March 11, 2005 9:53 AM
28
Operation with DVD and Video CD
Playback Setup
1. Turn on the TV and select the video input source
connected to the DVD+VCR.
2. Turn on the audio system (if applicable) and select
the input source connected to the DVD+VCR.
3. Press OPEN/CLOSE (<) to open the disc tray and
load your chosen disc in the tray, with the playback
side down.
4. Press OPEN/CLOSE (<) to close the tray.
Playback starts automatically. If playback does not
start, press
1
.
In some cases, the disc menu might appear instead.
5. To stop the playback, press .
The unit records the stopped point, depending on
the disc. “;∫” appears on the screen briefly. Press
1
to resume playback (from the scene point). If
you press again or unload the disc (“” appears
on the screen.), the unit will clear the stopped point.
Press OPEN/CLOSE (<) to remove the disc.
Press OPEN/CLOSE (<) to close disc tray or press
Í/I, the disc tray closes automatically and unit turns
off.
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD or Video CD which offer a menu.
Use the 2 1 3 4 buttons to select the title/chapter
you want to view, then press ENTER/OK to start.
Press TITLE or DISC MENU to return to the menu
screen.
Use the number buttons to select the track you want
to view and press RETURN to return to the menu
screen. Menu settings and operating procedures
may differ. Follow the instructions on each menu
screen. You also may set PBC to Off (See “PBC” on
page 18).
Notes:
If parental control is set and the disc is not within the rating
settings you must input the password.
(See “LOCK” on page 19).
DVDs may have a region code. Your player will not play discs
that have a region code different from your player. The region
code for this player is 2 (two).
In some cases, playback of discs recorded in the NTSC
system may be jerky.
General Features
Notes:
Unless stated otherwise, all operations described use
the remote control. Some features may also be available
on the Setup menu.
Moving to another TITLE
When a disc has more than one title, you can move to
another title. Press DISPLAY and select desired title by
using number (0-9) or 2 / 1 then press ENTER/OK to
move to another title.
Moving to another CHAPTER / TRACK
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
Press 9 or : briefly during playback to select
the next chapter/track or to return to the beginning of
the current chapter/track.
Press : twice in quick successions to step back to
the previous chapter/track.
To go directly to any chapter during DVD playback,
press DISPLAY and press 3 / 4 to select the
chapter/track icon. Input the chapter/track number (0-
9) or use 2 / 1.
Note:
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use this function (See “PBC” on page 18).
Slow Motion
1. Press 5 during still mode.
The DVD+VCR will now go into SLOW mode.
2. Use 5 to select the required speed:
F 1/7, F 1/6, F 1/4, or F 1/2 (forward).
3. To exit Slow Motion mode, press
1
.
Note:
Slow motion playback in reverse is not possible.
DVD
VCD
DVD
DVD VCD
DVD VCD
VJ9033CP1Z_E-EK.book Page 28 Friday, March 11, 2005 9:53 AM
29
Operation with DVD and Video CD
OPERATION
Still Picture and Frame-by-Frame Playback
1. Press ; during playback. Advance the picture
frame-by-frame by pressing ; repeatedly.
2. To exit still motion mode, press
1
.
Search
1. Press 6 or 5 during playback.
2. Press 6 or 5 repeatedly to select the required
speed:
DVD disc; X2, X4, X16 or X100
Video CD; X2, X4, X8
3. To exit SEARCH mode, press
1
.
Time Search
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback. The time search
box shows the elapsed playing time.
2. Press 3/4 to select the time clock icon and
“ -:--:-- ” appears.
3. Input the required start time in hours, minutes, and
seconds from left to right. If you enter the wrong
numbers, press CLEAR ( ) to remove the
numbers you entered. Then input the correct
numbers.
4. Press ENTER/OK to confirm. Playback starts from
the selected time.
Note:
On a Video CD with PBC, you must set PBC to Off on the setup
menu to use this function (See “PBC” on page 18).
Marker Search
To enter a Marker
You can start playback from up to nine memorized points.
To enter a marker, press MARKER at the desired point
on the disc. The Marker icon appears on the TV screen
briefly. Repeat to enter up to nine markers.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The marker
search menu appears on the screen.
2. Within 10 seconds, press 2/1 to select a marker
number that you want to recall or clear.
3. Press ENTER/OK and playback starts from the
marked scene. Or, Press CLEAR ( ) and the
marker number is erased from the list.
4. You can play any marker by inputting its number on
the marker search menu.
Repeat
You can repeat a title/chapter/all/track on a disc.
Press REPEAT during playback to select a desired
repeat mode.
DVD Video Discs - Repeat Chapter/Title/Off
Chapter: repeats the current chapter.
Title: repeats the current title.
Off: does not play repeatedly.
Video CDs - Repeat Track/All/Off
Track: repeats the current track
All: repeats all the tracks on a disc.
Off: does not play repeatedly.
Note:
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use this function (See “PBC” on page 18).
If you press 9 once during Repeat Chapter (Track)
playback, the repeat playback cancels.
Repeat A-B
To repeat a sequence.
1. Press REPEAT A-B at your chosen starting point.
“A- ” appears briefly on the TV screen.
2. Press REPEAT A-B again at your chosen end point.
“A- B” appears briefly on the TV screen and the
repeat sequence begins.
3. Press REPEAT A-B again to cancel.
Zoom
Use zoom to enlarge the video image.
1. Press ZOOM during playback or still playback to
activate the Zoom function. The square frame
appears briefly in the right bottom of the picture.
2. Each press of the ZOOM button changes the TV
screen in the sequence:
100% size 150% size 200% size 300% size
400% size 100% size.
3. Use the 2 134 buttons to move through the
zoomed picture.
4. To resume normal playback, press ZOOM
repeatedly or CLEAR ( ) button.
Note:
Zoom may not work on some DVDs.
DVD VCD
DVD VCD
DVD VCD
DVD VCD
1/9#5
123------
DVD VCD
DVD VCD
DVD VCD
VJ9033CP1Z_E-EK.book Page 29 Friday, March 11, 2005 9:53 AM
30
Operation with DVD and Video CD
Changing the Audio Channel
Press AUDIO repeatedly during playback to hear a
different audio channel (Stereo, Left, Right).
Last Scene Memory
This player memorizes last scene from the last disc that
is viewed. The last scene remains in memory even if you
remove the disc from the player or switch off the player.
If you load a disc that has the scene memorized, the
scene is automatically recalled.
Note:
This player does not memorize the scene of a disc if you switch
off the player before commencing to play the disc.
Instant Replay
Press AUX during playback and the disc will reverse
picture search through 10 seconds of playback. And then
the playback will start from the point again.
Screen Saver
The screen saver appears when you leave the
DVD+VCR in Stop mode for about five minutes.
Special DVD Features
Checking the contents of DVD discs: Menus
DVDs may offer menus that allow you to access special
features. To use the disc menu, press DISC MENU.
Input the corresponding number or use the 2 134
buttons to highlight your selection.
Then press ENTER/OK.
Title Menu
1. Press TITLE. If the current title has a menu, the
menu appears on the screen. Otherwise, the disc
menu may appear.
2. The menu offers features such as camera angles,
spoken language and subtitle options, and chapters
for the title.
3. Press TITLE to exit.
Disc Menu
Press DISC MENU and the disc menu is displayed.
Press DISC MENU again to exit.
Camera Angle
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback. Press ANGLE repeatedly during
playback to select a desired angle. Note that the number
of the current angle appears on the display.
Tip:
The Camera Angle icon is displayed on the TV screen when
alternate angles are available.
Changing the Audio Language
Press A.MONITOR repeatedly during playback to hear a
different audio language or audio track.
Subtitles
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
Note:
If there is no information, is displayed.
VCD
DVD CD VCD
DVD
DVD
DVD
DVD
DVD
DVD
VJ9033CP1Z_E-EK.book Page 30 Friday, March 11, 2005 9:53 AM
31
OPERATION
Operation with Audio CD and MP3 Disc
On-Screen Display - DVD
You can display the general playback status on the TV
screen. Some items can be changed using the menu.
To use the on-screen display:
1. Press DISPLAY during playback.
2. Press 3 / 4 to select an item.
The selected item is highlighted.
3. Press 2 / 1 to change the setting. You can also use
the number buttons if appropriate (e.g. inputting the
title number). For some functions, press ENTER/OK
to execute the setting.
Notes:
Some discs may not provide all of the features shown below.
If no button is pressed for 10 seconds, the on-screen display
disappears.
If is displayed, action prohibited or not available.
Example: On-Screen Display during playing
DVD Video
Example: On-Screen Display during playing
VCD
Maintenance and Service
Refer to the information in this chapter before contacting
a service technician.
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally packed at
the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit.
Do not leave rubber or plastic products in contact with
the unit for a long period of time. since they leave
marks on the surface.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the surfaces
are extremely dirty, use a soft cloth lightly moistened with
a mild detergent solution.
Do not use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the unit.
Maintaining the Unit
The DVD+VCR is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or worn,
the picture quality could be diminished.
Depending on the operating environment, regular
inspection and maintenance are recommended after
every 1,000 hours of use.
For details, please contact your nearest authorized
service center.
Items Selection Method
Title Number
2 / 1, Numbers
ENTER/OK
Chapter Number
2 / 1, Numbers
ENTER/OK
Time search
Numbers
ENTER/OK
Items Selection Method
Track Number
(or PBC mode)
2 / 1, Numbers
ENTER/OK
Time search
Numbers
ENTER/OK
1 / 1
1 / 18
-:--:--
1 / 1
-:--:--
VJ9033CP1Z_E-EK.book Page 31 Friday, March 11, 2005 9:53 AM
32
Playing an Audio CD or MP3 Disc
The DVD+VCR can play MP3 formatted recordings on
CD-ROM, CD-R, or CD-RW discs.
Audio CD
Once you insert an audio CD a menu appears on the TV
screen. Press 3 / 4 to select a track then press
1
or
ENTER/OK and playback starts.
MP3
1. Press 3 / 4 to select a folder, and press ENTER/
OK to see the folder contents.
2. Press 3 / 4 to select a track then press
1
or
ENTER/OK. Playback starts.
ID3 TAG
When playing a file containing information such as
track titles, you can see the information by pressing
DISPLAY. [ Song, Artist, Album, Comment, Genre ]
If there is no information, “No ID3 TAG” appear on the
menu screen.
Tips:
If you are in a file list on the “MUSIC” menu and want to
return to the Folder list, use the 3 / 4 to highlight and
press ENTER/OK.
To go directly to any track, input the track number (0-9).
On a CD with MP3 and JPEG you can switch MP3 and
JPEG. Press TITLE and “MUSIC” or “PHOTO” word on top of
the menu is highlighted.
Program
List
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
Track 7
Track 8
AUDIO CD
0:52:07
1 / 12
Clear All
PROGRAM
Edit
Program
List
0:00:00
1 / 12
Clear All
PROGRAM
Edit
DISPLAY
Info
MUSIC
2-Music2
1-Music1
3-Music3
4-Music4
5-Music5
6-Music6
7-Music7
MP3 disc compatibility with this player is limited
as follows:
Sampling frequency: within 8 - 48 kHz
Bit rate: within 32 - 320kbps
The player cannot read an MP3 file that has a file
extension other than “.mp3”.
CD-R physical format should be ISO 9660
If you record MP3 files using software that cannot
create a file system (eg. Direct-CD) it is impossible
to playback MP3 files. We recommend that you use
Easy-CD Creator, which creates an ISO 9660 file
system.
File names should have a maximum of 8 letters
and must incorporate an .mp3 extension.
They should not contain special letters such as / ?
* : “ < > l etc.
The total number of contens on the disc should be
less than 1500 files and 300 folders.
This DVD player requires discs and recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are many
different types of recordable disc formats (including
CD-R containing MP3 or WMA files) and these
require certain pre-existing conditions (see above) to
ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has no
right to grant such permission. Permission
should always be sought from the copyright
owner.
VJ9033CP1Z_E-EK.book Page 32 Friday, March 11, 2005 9:53 AM
33
Playing an Audio CD or MP3 Disc
OPERATION
Audio CD and MP3 Disc Features
Pause
1. Press ; during playback.
2. To return to playback, press
1
or press ; again.
Moving to another Track
1. Press 9 or : briefly during playback to go to
the next track or to return to the beginning of the
current track.
2. Press : twice in quick successions to go back to
the previous track.
3. You can play any track by inputting its number.
Repeat Track / All / Off
You can play a track/all on a disc.
1. Press REPEAT when playing a disc. The repeat icon
appears.
2. Press REPEAT to select a desired repeat mode.
Track: repeats the current track.
All: repeats all the tracks on a disc.
Off (No display): does not play repeatedly.
Note:
If you press 9 once during Repeat Track playback, the repeat
playback will be cancelled.
Search
1. Press 6 or 5 during playback.
2. Press 6 or 5 repeatedly to select the required
speed:
X2, X4 and X8 backward or forward.
3. To exit SEARCH mode, press
1
.
Random
1. Press RANDOM during playback. Random Playback
begins immediately and “Random” appears on the
menu screen.
2. To return to normal playback, press RANDOM
repeatedly until “Random” disappears from the
menu screen.
Tip:
By pressing 9 or : during random playback, the unit
selects another track and resumes random playback.
Repeat A-B
1. To repeat a sequence during disc playback press
REPEAT A-B at your chosen starting point. The
Repeat icon and “A -” appear on the menu screen.
2. Press REPEAT A-B again at your chosen end point.
The Repeat icon and “A-B” appear on the menu
screen, and the sequence begins to play repeatedly.
3. To exit the sequence and return to normal play,
press REPEAT A-B again. The Repeat icon
disappears from the menu screen.
CD MP3
CD MP3
CD MP3
CD MP3
CD MP3
CD
VJ9033CP1Z_E-EK.book Page 33 Friday, March 11, 2005 9:53 AM
34
Playing an Audio CD or MP3 Disc
Programmed Playback
The program function enables you to store your favourite
tracks from any disc in the player memory.
A program can contain 30 tracks.
1. Insert a disc.
AUDIO CD or MUSIC menu appears.
2. Press MNL.PROG.
The
E
mark will appear to the right of the word
“Program” on the right side of the menu screen.
Note:
Press MNL.PROG. again, the
E
mark will disappear to exit
the Program Edit mode.
3. Select a track on the “List”, then press ENTER/OK to
place the selected track on the “Program” list.
Repeat to place additional tracks on the list.
4. Press 1.
Select the track you want to start playing in the
“Program” list.
5. Press
1
or ENTER/OK to start. Playback begins in
the order in which you programmed the tracks.
Playback stops after all of the tracks on the
“Program” list have played once.
6. To resume normal playback from programmed
playback, select a track of AUDIO CD (or MUSIC) list
and then press
1
or ENTER/OK.
Note:
When you play the programmed track, the
E
mark will disappear
then the program edit mode will disable.
Repeat Programmed Tracks
1. Press REPEAT when playing a disc. The repeat icon
appears.
2. Press REPEAT to select a desired repeat mode.
Track: repeats the current track
All: repeats all the tracks on programmed list.
Off (No display): does not play repeatedly.
Note:
If you press 9 once during Repeat Track playback, the repeat
playback will be cancelled.
Erasing a Track from “Program” List
1. During STOP mode, press MNL.PROG. and
E
mark
will appear.
2. Use 1 / 3 / 4 to select the track that you wish to
erase from the Program list.
3. Press CLEAR ( ).
Repeat to erase additional tracks on the list.
Erasing the Complete Program List
1. During STOP mode, press MNL.PROG. and
E
mark
will appear.
2. Use 1 / 3 / 4 to select “Clear All” in the “Program”
list, then press ENTER/OK.
Note:
The programs are also cleared when the disc is removed.
Program
List
AUDIO CD
0:52:07
6 / 16
Clear All
PROGRAM
Edit
03-TRACK03
01-TRACK01
02-TRACK02
03-TRACK04
04-TRACK06
02-TRACK02
01-TRACK01
04-TRACK04
05-TRACK05
06-TRACK06
07-TRACK07
08-TRACK08
E
Audio CD Program Menu
Program
List
0:00:00
4 / 4
Clear All
PROGRAM
Edit
MUSIC
DISPLAY
Info
03 File 03
04 File 04
05 File 05
06 File 06
07 File 07
08 File 08
09 File 09
10 File 10
03 File 03
06 File 06
08 File 08
10 File 10
MP3
E
MP3 Program Menu
VJ9033CP1Z_E-EK.book Page 34 Friday, March 11, 2005 9:53 AM
35
OPERATION
Viewing a JPEG Disc
Using this DVD+VCR you can view discs with JPEG files.
1. Insert a disc and close the tray. The PHOTO menu
appears on the TV screen.
2. Press 3 / 4 to select a folder, and press ENTER/
OK. A list of files in the folder appears. If you are in a
file list and want to return to the previous Folder list,
use the 3 / 4 buttons on the remote to highlight
and press ENTER/OK.
3. If you want to view a particular file, press 3 / 4 to
highlight a file and press ENTER/OK or
1
.
The selected file will appear for viewing.
The on-screen messages displayed with the file can
be turned off by pressing the RETURN (Hide) button
on the remote control.
While viewing a file, you can press to move to the
previous menu (PHOTO menu).
Tips:
Information and user guidance regarding the current image
is displayed in the lower part of the screen. You can toggle
this bar on and off using RETURN.
There are three Slide Speed options :
>>> (Fast), >> (Normal) and > (Slow)
Use 342 1 to highlight the Speed. Then, use 2 / 1 to
select the option you want to use then press ENTER/OK.
On a disc with MP3 and JPEG you can switch MP3 and
JPEG. Press TITLE and MUSIC or PHOTO word on top of
the menu is highlighted.
Slide Show
Use 342 1 to highlight the (Slide Show) then
press ENTER/OK.
Still Picture
1. Press ; during slide show.
The player will now go into PAUSE mode.
2. To return to the slide show, press
1
or press ;
again.
Moving to another File
Press 9 or : or cursor (2 or 1) once while
viewing a picture to advance to the next or previous file.
Zoom
Use zoom to enlarge the photo image. (see page 29)
To rotate picture
Press 3 / 4 during showing a picture to rotate the
picture clockwise or counter clockwise.
Preview
List
Folder 00
Folder 01
Folder 02
Folder 03
Folder 04
01 FILE 01
02 FILE 02
03 FILE 03
>>>
PHOTO
/FILE 01
JPEG disc compatibility with this player is
limited as follows:
Depending upon the size and number of JPEG
files, it could take a long time for the DVD+VCR to
read the disc’s contents. If you don’t see an on-
screen display after several minutes, some of the
files may be too large — reduce the resolution of
the JPEG files to less than 5760 (Horizontal) x
4608 (Vertical) pixels and burn another disc.
The total number of contens on the disc should be
less than 1500 files and 300 folders.
Some discs may be incompatible due to a different
recording format or the condition of disc.
Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.
File names without “.jpg” extension will not be able
to be read by this DVD+VCR. Even though the files
are shown as JPEG image files in Windows
Explorer.
JPEG
JPEG
JPEG
JPEG
JPEG
VJ9033CP1Z_E-EK.book Page 35 Friday, March 11, 2005 9:53 AM
36
Language and Area Code List
Language Code List
Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu.
Area Code List
Choose a area code from this list.
Language Code Language Code Language Code Language Code
Abkhazian 6566 Fiji 7074 Lingala 7678 Singhalese 8373
Afar 6565 Finnish 7073 Lithuanian 7684 Slovak 8375
Afrikaans 6570 French 7082 Macedonian 7775 Slovenian 8376
Albanian 8381 Frisian 7089 Malagasy 7771 Somali 8379
Ameharic 6577 Galician 7176 Malay 7783 Spanish 6983
Arabic 6582 Georgian 7565 Malayalam 7776 Sudanese 8385
Armenian 7289 German 6869 Maltese 7784 Swahili 8387
Assamese 6583 Greek 6976 Maori 7773 Swedish 8386
Aymara 6588 Greenlandic 7576 Marathi 7782 Tagalog 8476
Azerbaijani 6590 Guarani 7178 Moldavian 7779 Tajik 8471
Bashkir 6665 Gujarati 7185 Mongolian 7778 Tamil 8465
Basque 6985 Hausa 7265 Nauru 7865 Tatar 8484
Bengali; Bangla 6678 Hebrew 7387 Nepali 7869 Telugu 8469
Bhutani 6890 Hindi 7273 Norwegian 7879 Thai 8472
Bihari 6672 Hungarian 7285 Oriya 7982 Tibetan 6679
Breton 6682 Icelandic 7383 Panjabi 8065 Tigrinya 8473
Bulgarian 6671 Indonesian 7378 Pashto, Pushto 8083 Tonga 8479
Burmese 7789 Interlingua 7365 Persian 7065 Turkish 8482
Byelorussian 6669 Irish 7165 Polish 8076 Turkmen 8475
Cambodian 7577 Italian 7384 Portuguese 8084 Twi 8487
Catalan 6765 Japanese 7465 Quechua 8185 Ukrainian 8575
Chinese 9072 Javanese 7487 Rhaeto-Romance 8277 Urdu 8582
Corsican 6779 Kannada 7578 Rumanian 8279 Uzbek 8590
Croatian 7282 Kashmiri 7583 Russian 8285 Vietnamese 8673
Czech 6783 Kazakh 7575 Samoan 8377 Volapük 8679
Danish 6865 Kirghiz 7589 Sanskrit 8365 Welsh 6789
Dutch 7876 Korean 7579 Scots Gaelic 7168 Wolof 8779
English 6978 Kurdish 7585 Serbian 8382 Xhosa 8872
Esperanto 6979 Laothian 7679 Serbo-Croatian 8372 Yiddish 7473
Estonian 6984 Latin 7665 Shona 8378 Yoruba 8979
Faroese 7079 Latvian, Lettish 7686 Sindhi 8368 Zulu 9085
Area Code Area Code Area Code Area Code
Afghanistan AF Ethiopia ET Malaysia MY Saudi Arabia SA
Argentina AR Fiji FJ Maldives MV Senegal SN
Australia AU Finland FI Mexico MX Singapore SG
Austria AT France FR Monaco MC Slovak Republic SK
Belgium BE Germany DE Mongolia MN Slovenia SI
Bhutan BT Great Britain GB Morocco MA South Africa ZA
Bolivia BO Greece GR Nepal NP South Korea KR
Brazil BR Greenland GL Netherlands NL Spain ES
Cambodia KH Islands HM
Netherlands Antilles
AN Sri Lanka LK
Canada CA Hong Kong HK New Zealand NZ Sweden SE
Chile CL Hungary HU Nigeria NG Switzerland CH
China CN India IN Norway NO Taiwan TW
Colombia CO Indonesia ID Oman OM Thailand TH
Congo CG Israel IL Pakistan PK Turkey TR
Costa Rica CR Italy IT Panama PA Uganda UG
Croatia HR Jamaica JM Paraguay PY Ukraine UA
Czech Republic CZ Japan JP Philippines PH United States US
Denmark DK Kenya KE Poland PL Uruguay UY
Ecuador EC Kuwait KW Portugal PT Uzbekistan UZ
Egypt EG Libya LY Romania RO Vietnam VN
El Salvador SV Luxembourg LU
Russian Federation
RU Zimbabwe ZW
VJ9033CP1Z_E-EK.book Page 36 Friday, March 11, 2005 9:53 AM
37
REFERENCE
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Symptom Cause Correction
No power. The power cord is disconnected. Plug the power cord into the wall outlet
securely.
The power is on, but the
DVD+VCR does not
work.
DVD or VCR button is not switched
properly.
Refer to page 5.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
No picture. The TV is not set to receive DVD+VCR
signal output.
Select the appropriate video input
mode on the TV so the picture from the
DVD+VCR player appears on the TV
screen.
The video cable is not connected securely. Connect the video cable into the jacks
securely.
Mismatch setting between TV and this
unit.
Select the correct Video Output in
SETUP menu.
Wrong connection. Check the connection.
No sound. The equipment connected with the audio
cable is not set to receive DVD+VCR
signal output.
Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
The audio cables are not connected
securely.
Connect the audio cable into the jacks
securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The AUDIO options are set to the wrong
position.
Set the AUDIO options to the correct
position.
The playback picture is
poor.
The disc is dirty. Clean the disc.
The TV channels are not tuned in
properly.
Check tuning, carry out tuning again.
Tape heads are dirty. Clean video heads.
Tape is a rental or was recorded on
another VCR.
Use PR/TRK (3/4) for manual
tracking adjustment while tape is
playing.
VJ9033CP1Z_E-EK.book Page 37 Friday, March 11, 2005 9:53 AM
38
Troubleshooting (Continued)
Symptom Cause Correction
The DVD+VCR does not
start playback.
An unplayable disc is inserted. Insert a playable disc. (Check the disc
type and Regional code.)
The disc is placed upside down. Place the disc with the playback side
down.
The disc is not placed within the guide. Place the disc on the disc tray correctly
inside the guide.
The disc is dirty. Clean the disc.
The Rating level is set. Cancel the Rating function or change
the rating level.
Video tape cannot be
inserted.
Is the cassette compartment empty? Eject the tape in.
No Hi-Fi sound Audio mode is not set properly. Select STEREO by repeatedly pressing
AUDIO on the remote control.
No NICAM sound
recording
NICAM mode is not set properly. Make sure NICAM in the menu is set to
AUTO for the station to be recorded.
The remote control does
not work properly.
There is an obstacle in the path of the
remote control and this unit.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
The remote control is not pointed at the
remote sensor of the DVD+VCR.
Point the remote control at the remote
sensor of the DVD+VCR.
The remote control is too far from the
DVD+VCR.
Operate the remote control within 23ft
(7 m).
This remote control use the same buttons
for VCR and DVD functions (ex.PLAY).
When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
Timer recording is not
possible.
Clock in DVD+VCR is not set to correct
time.
Set clock to correct time.
Timer has been programmed incorrectly. Reprogram Timer.
indicator light does not appear after
programming timer.
Reprogram Timer and turn DVD+VCR
off to enable timer.
VJ9033CP1Z_E-EK.book Page 38 Friday, March 11, 2005 9:53 AM
39
REFERENCE
Specification
General
System
Inputs (VCR)
Outputs (DVD)
Outputs (VCR/DVD)
Designs and specifications are subject to change without notice.
Power requirements AC 200-240 V, 50 Hz
Power consumption 17 W
Dimensions (approx.) 430 X 78.5 X 265 mm (w/h/d)
Mass (approx.) 4.2 kg
Operating temperature 5°C to 35°C (41°F to 95°F)
Operating humidity 5 % to 90 %
Timer 24 hours display type
RF Modulator UHF 22-68 (Adjustable)
Laser Semiconductor laser, wavelength 650 nm
Video Head system Double azimuth 6 heads, helical scanning.
Signal system PAL
Frequency response DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio More than 100 dB (ANALOG OUT connectors only)
Harmonic distortion Less than 0.008%
Dynamic range More than 100 dB (DVD)
More than 95 dB (CD)
Audio -6.0 dBm, more than 10 kohms (SCART)
-6.0 dBm, more than 47 kohms (RCA)
Video 1.0 V (p-p), 75 ohms, unbalanced (SCART/RCA)
VIDEO OUT 1 Vp-p 75 ohms, sync negative
Audio output (digital audio) 0.5 V (p-p), 75 ohms, RCA jack x 1
Audio output (analog audio) 2.0 Vrms (1 kHz, 0 dB), 600 ohms, RCA jack (L, R) x 1/SCART (TO TV)
Audio -6.0 dBm, less than 1 kohms (SCART)
Video 1.0 V (p-p), 75 ohms, unbalanced (SCART)
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
DTS and DTS Digital Out are trademarks of Digital Theater Systems, Inc.
VJ9033CP1Z_E-EK.book Page 39 Friday, March 11, 2005 9:53 AM
40
Precautions
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these
batteries must be followed strictly.
Failure to heed the following precautions may result in damage to the unit, remote control or disc.
1. DO NOT
place the unit —
— in an environment prone to extreme temperatures or humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are generated.
— on a surface that is unstable or subject to vibration.
2. DO NOT
block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
3. DO NOT
place heavy objects on the unit or remote control.
4. DO NOT
place anything which might spill on top of the unit or remote control.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
5. DO NOT
expose the apparatus to dripping or splashing.
6. DO NOT
use this equipment in a bathroom or places with water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit.
7. DO NOT
place any naked flame sources, such as lighted candles, on the apparatus.
8. AVOID
violent shocks to the unit during transport.
Some Do's And Don'ts On The Safe Use Of Equipment
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment,
care must be taken if you are to obtain the best results and safety is to be assured.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly
made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way—switch off, withdraw the
mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby
mode. Switch off using the switch on the equipment and make sure that your family knows how to do this. Special arrangements may need to be made
for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of road safety. It is illegal to watch
television whilst driving.
DON’T listen to headphones at high volume, as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause damage and shorten the life of
the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the manufacturer’s approved stand or legs
with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL...
IMPORTANT
Connection to the mains supply in the United Kingdom.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety
approved extension lead or consult your dealer.
In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to
replace the fuse cover. If the fuse fails again consult your nearest JVC dealer.
If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent
connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow the instructions given below:
DO NOT make any connection to the Larger Terminal coded E or Green.
The wires in the mains lead are coloured in accordance with the following code:
If these colours do not correspond with the terminal identifications of your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured Black.
Brown wire to terminal coded L (Live) or coloured Red.
If in doubt — consult a competent electrician.
NEVER let anyone especially children push anything into holes, slots or any other opening in the case—this could result in a fatal electrical
shock;
NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!
Blue to N (Neutral) or Black
Brown to L (Live) or Red
VJ9033CP1Z_E-EK.book Page 40 Friday, March 11, 2005 9:53 AM
41
VJ9033CP1Z_E-EK.book Page 41 Friday, March 11, 2005 9:53 AM
42
VJ9033CP1Z_E-EK.book Page 42 Friday, March 11, 2005 9:53 AM
43
VJ9033CP1Z_E-EK.book Page 43 Friday, March 11, 2005 9:53 AM
© 2005 Victor Company of Japan, Limited
HR-XV28S
EN
Printed in Indonesia
0305MNH-AL-OT
EK
VJ9033CP1Z_E-EK.book Page 92 Friday, March 11, 2005 9:53 AM
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

jvc-hr-xv28
  • Hallo,
    wo finde ich einen UsB 2.0 Video capture Treiber für Windows 8.1? Vielen Dank für Ihre Hilfe Eingereicht am 24-6-2019 15:15

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC HR-XV28 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von JVC HR-XV28

JVC HR-XV28 Bedienungsanleitung - Deutsch - 40 seiten

JVC HR-XV28 Bedienungsanleitung - Holländisch - 40 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info