Bedienungsanleitung JVC HR-XVC20U (Seite 33 von 68) (Englisch)

658633

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Timer recording

Press SET UP MENU. Select the

TIMER REC SET option, then press

ENTER.

Press SET + or – to select the date,

then press ENTER.

Press SET + or – to select one of the

program line, then press ENTER.

Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode.

Load a cassette tape with the erase prevention tab intact.

Press OSD to verify time and date are correct (see page 31).

Preparation:

•

Timer recording can be programmed

on-screen with the remote control.

The built-in timer allows automatic

unattended recording of up to 8

programs within 1 month.

Set the start time, end time, channel

and tape speed as in step 3.

Example: Program a timer recording for the 26th day, channel 125

(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP).

NOTES:

If the programmed start time is over the

present time, the program will be canceled

after pressed ENTER.

•

To enter other programs, repeat step

2 through 4.

• To return to the normal screen,

press SET UP MENU twice.

Press TIMER. The clock symbol ( ) will appear on the

display and the VCR stands by for recording. At the same

time, VCR mode will change to DVD mode automatically. You

can use DVD even if the VCR is in the timer recording mode.

If you do not use the DVD, turn the power off.

The timer recording will start at 5 seconds before the time you

predetermined.

NOTES:

If the clock symbol (

) does not appear on the display in spite

of the pressing of TIMER, the cassette may not have been

loaded yet (see page 26).

If the cassette is ejected in spite of the pressing of TIMER , the

erase prevention tab of the cassette may have been removed

(see page 26).

•

NOTES:

If the clock symbol ( ) blinks when

the timer recording ended, the TV

program has not been completely

recorded because of an insufficient

tape supply. In this case, press TIMER

to cancel the timer program or press

EJECT to remove the cassette tape.

During timer recording standby mode,

the VCR mode cannot be selected. To

use the VCR, press TIMER at first,

then press VCR to change to VCR

mode. After you use the VCR, press

TIMER again to put the VCR into timer

recording standby mode.

If you press TIMER during timer

recording, the recording operation will

be interrupted. If you press TIMER

again within the programmed time, the

recording operation will start again.

After a power failure or disconnection

of the power plug, all programmed

recording settings and time display

will be lost upon resumption of power.

In this case, reset the clock (see pages

23-25) and reprogram any timer

recordings.

•

Press CANCEL to move cursor backward for correction.

To record from external source set the channel to “L”. “L” will appear

next to CH 125 (or 69).

2C50101BE(30-35) 13/5/03, 3:33 PM33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-XVC20U Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info