Bedienungsanleitung JVC HRDD868 (Seite 31 von 68) (Englisch)

30997

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

EN 31

Auto SP

→

LP Timer

If, when timer-recording in SP mode, there is not enough tape to

record the entire programme, the recorder automatically

switches to LP mode to allow complete recording.

For Example . . .

Recording a programme of 210 minutes in length onto a 180-

minute tape

NOTES:

●

If you have programmed the recorder to timer-record 2 or

more programmes, the second programme and those

thereafter may not fit on the tape if you set "AUTO SP

→

TIMER" to "ON". In this case, make sure the mode is not

engaged, then set the tape speed manually during timer

programming.

●

In order to ensure that the recording fits on the tape, this

feature may leave a slight non-recorded section at the end of

the tape.

●

There may be some noise and sound disturbance at the point

on the tape where the recorder switches from SP to LP mode.

●

The Auto SP

→

LP Timer feature is not available during ITR

(Instant Timer Recording), and the feature will not work

properly with any tapes longer than E-180 or with some tapes

of shorter lengths.

●

If you perform timer recording with both VPS/PDC and the

Auto SP

→

LP Timer activated, and the programme goes

beyond its originally scheduled length, there may be times

when the programme cannot be recorded in its entirety.

Total 210 minutes

Approximately 150 minutes Approximately 60 minutes

SP mode LP mode

Make sure you set "AUTO SP→LP TIMER" to "ON" at the Mode

Set screen before the timer-recording starts.

ACCESS MAIN MENU SCREEN

Press MENU.

ACCESS MODE SET SCREEN

Press %ﬁ to move the highlight bar (pointer) to "MODE

SET", then press OK or

SELECT MODE

Press %ﬁ to move the

highlight bar (pointer) to

"AUTO SP→LP TIMER",

then press OK or

to select

"ON".

RETURN TO NORMAL SCREEN

Press MENU.

MODE SET

B. E. S. T. ON

PICTURE CONTROL AUTO

AUTO TIMER OFF

O. S. D. ON

DIRECT REC ON

AUTO SP=LP TIMER ON

POWER SAVE OFF

[5∞] =

[MENU] : EXIT

1 2 3

4 5 6

7 8 9



Auto Timer

When the Auto Timer is set to ON the timer is automatically

engaged when the recorder power is turned off and automati-

cally disengaged when the recorder is powered back on.

ACCESS MAIN MENU SCREEN

Press MENU.

ACCESS MODE SET SCREEN

Press %ﬁ to move the

highlight bar (pointer) to

"MODE SET", then press

OK or

SELECT MODE

Press %ﬁ to move the

highlight bar (pointer) to

"AUTO TIMER", then press

OK or

to select either

"ON" or "OFF".

RETURN TO NORMAL SCREEN

Press MENU.

NOTE:

For safety, when Auto timer is set to "OFF", all other recorder

functions are disabled while the Timer mode is engaged. To

disengage the timer, press

‰

(TIMER).

MODE SET

B. E. S. T. ON

PICTURE CONTROL AUTO

AUTO TIMER ON

O. S. D. ON

DIRECT REC ON

AUTO SP=LP TIMER OFF

POWER SAVE OFF

[5∞] =

[MENU] : EXIT

MAIN MENU

MODE SET

AUTO CH SET

MANUAL CH SET

INITIAL SET

REC LEVEL CTL

[

∞

] =

[MENU] : EXIT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HRDD868 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info