Bedienungsanleitung JVC HRJ470 (Seite 51 von 56) (Englisch)

31011

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Filename [HRJ670EU3.fm]

Masterpage:Right

RECORDING

TIMER RECORDING

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Recording cannot be started.

●

There is no cassette loaded, or the

cassette loaded has had its record safety

tab removed.

Insert a cassette, or using adhesive tape,

reseal the slot where the tab was removed.

2. TV broadcasts cannot be recorded.

●

“L-1”, “L-2” or “SAT” has been selected

as the input mode.

Set to the desired channel.

3. Tape-to-tape editing is not possible.

●

The source (another video recorder,

camcorder) has not been properly

connected.

Confirm that the source is properly

connected.

●

All necessary power switches have not

been turned on.

Confirm that all units’ power switches are

turned on.

●

The input mode is not correct. Set the input mode to “L-1”, “L-2” or

“SAT”.

4. Camcorder recording is not possible.

●

The camcorder has not been properly

connected.

Confirm that the camcorder is properly

connected.

●

The input mode is not correct. Set the input mode to “L-1”, “L-2” or

“SAT”.

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Timer recording won’t work.

●

The clock and/or the timer have been set

incorrectly.

Re-perform the clock and/or timer

settings.

●

The timer is not engaged. Press

# and confirm that “#” is

displayed on the front display panel.

2. Timer programming is not possible.

●

Timer recording is in progress. Timer programming can’t be performed

while a timer recording is in progress.

Wait until it finishes.

3. “

#” and “[” on the front display

panel won’t stop blinking.

●

The timer is engaged but there’s no

cassette loaded.

Load a cassette with the record safety tab

intact, or cover the hole using adhesive

tape.

4. The cassette is automatically ejected,

and “

#” and “[” on the front

display panel won’t stop blinking.

●

The loaded cassette has had its record

safety tab removed.

Remove the cassette and cover the hole

with adhesive tape, or insert a cassette

with the record safety tab intact.

5. “

#” blinks for 10 seconds and the

Timer mode is disengaged.

●

# has been pressed when there are no

programs in memory, or the timer

record information has been

programmed incorrectly.

Check the programmed data and re-

program as necessary, then press

# again.

6. The cassette is automatically ejected,

the power shuts off and “

#” and

“

[” won’t stop blinking.

●

The end of the tape was reached during

timer recording.

The programme may not have been

recorded in its entirety. Next time make

sure you have enough time on the tape to

record the entire programme.

7. The S

HOW

IEW

system does not timer-

record properly.

●

The recorder’s channel positions have

been set incorrectly.

Refer to “Guide Program Number Set”

(

੬

pg. 47) and re-perform the procedure.

HRJ670EU3.fm Page 51 Thursday, December 9, 1999 3:51 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HRJ470 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info