474089
47
Zoom out
Zoom in
Vorherige Seite
1/53
Nächste Seite
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / All Cover
Cover02
LCT1537-001A-U_Cover.fm Page 2 Thursday, September 25, 2003 10:00 AM
1
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Thank you for buying this JVC colour television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
Avoid improper installation and never position the unit
where good ventilation is unattainable.
When installing this television, distance recommendations
must be maintained between the floor and wall, as well as
installation in a tightly enclosed area or piece of furniture.
Adhere to the minimum distance guidelines shown for safe
operation.
Failure to heed the following precautions may result in damage to the TV or
remote control.
DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)
DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)
DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT place any naked flame sources, such as lighted candles, on the TV.
CAUTION:
Operate only from the power source specified
(AC 220 – 240 V, 50 Hz) on the unit.
Avoid damaging the AC plug and power cord.
When you are not using this unit for a long
period of time, it is recommended that you
disconnect the power cord from the main
outlet.
The main power button on the TV does not
fully isolate the TV from the AC supply. If you
are not going to use this TV for a long period
of time, be sure to disconnect the AC plug from
the AC socket.
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.
Never use any cleaner or detergent on it.
In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it
yourself or remove the rear cover.
D.I.S.T. demonstration
To start the D.I.S.T. demonstration:
Press the H button to display the menu bar. Then press the yellow button.
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.
To quit the D.I.S.T. demonstration:
Press the yellow button, b button, p p buttons or any of the number buttons.
HV-36P38SUE_Eng.book Page 1 Friday, September 26, 2003 11:10 AM
3
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Setting up your TV
Caution
Turn off all the equipment including the TV before connecting anything.
Connecting the aerial and VCR
The connecting cables are not provided.
For further details, refer to the manuals provided with the devices to be connected.
If connecting a VCR, follow A
AA
A
B
BB
B
C
CC
C.
If not connecting a VCR, follow 1
11
1.
To operate T-V LINK functions, a T-V
LINK compatible VCR must be connected to
the EXT-2 terminal on the TV. For details
about T-V LINK functions, see “T-V LINK
FUNCTIONS” on page 9.
A video can be viewed from the VCR
without performing C. For details, refer
to your VCR instruction manual.
To connect additional external devices,
please see “Connecting the external
devices” on page 40.
To connect additional audio equipments,
see “Connecting Speakers/Amplifier” on
page 42.
When a decoder is connected to a T-V
LINK compatible VCR, set the
DECODER (EXT-2) function to ON. For
details, see “DECODER (EXT-2)” on
page 36. Otherwise, you will not be able
to view scrambled channels.
EXT-1
EXT-
4
EXT-2
S
EXT-3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
75-ohm
Coaxial
Cable
21-pin
SCART
Cable
Back of the TV
75-ohm
Coaxial
Cable
AV IN/OUT
Terminal
To Aerial
Output
To Aerial
Input
VCR
Aerial
EXT-1
EXT-
4
EXT-2
S
EXT-3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
75-ohm
Coaxial
Cable
21-pin
SCART
Cable
Back of the TV
75-ohm
Coaxial
Cable
AV IN/OUT
Terminal
To Aerial
Output
To Aerial
Input
Aerial
HV-36P38SUE
HV-32P37SUE/HV-28P37SUE
VCR
HV-36P38SUE_Eng.book Page 3 Friday, September 26, 2003 11:10 AM
4
Setting up your TV
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Rear Panel
1 Aerial socket (page 3)
2 Woofer terminal (pages 5)
3 EXT-1 terminal (pages 3, 37, 40)
4 EXT-2 terminal (pages 3, 9, 37, 40)
5 EXT-3 terminal (pages 37, 40)
6 EXT-4 terminal (pages 37, 40)
7 AUDIO OUT terminal (page 42)
1 Aerial socket (page 3)
2 EXT-1 terminal (pages 3, 37, 40)
3 EXT-2 terminal (pages 3, 9, 37, 40)
4 EXT-3 terminal (pages 37, 40)
5 EXT-4 terminal (pages 37, 40)
6 AUDIO OUT terminal (page 42)
EXT-
1
EXT-
4
EXT-
2
S
EXT-
3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
HV-36P38SUE
EXT-1
EXT- 4
EXT-2
S
EXT-3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
HV-32P37SUE/HV-28P37SUE
HV-36P38SUE_Eng.book Page 4 Friday, September 26, 2003 11:10 AM
Setting up your TV
5
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Connecting and placing the
woofer unit (HV-36P38SUE
only)
Connect the supplied woofer connector to the
woofer terminal on the back of the TV.
If the woofer unit is not connected, you will
not be able to enjoy the bass sound.
Connect so that the lever is raised.
When disconnecting the woofer
connector, do so while pushing the lever.
Placing the woofer unit
As shown in the diagram, affix the
supplied stoppers to the four corners
of the side of the woofer unit that will
be used as the base.
The woofer unit can be used either standing
up or lying down.
There is no difference between the top and
bottom of the woofer unit irrespective of
whether it is being used standing up or lying
down.
Place the woofer unit within the range
of the connection cable.
It is recommended that the woofer unit be
placed with the speaker facing forwards.
Pay attention to the following in order
to prevent unnatural colours from
appearing in the corner of the screen.
Place the woofer unit at least 20 cm away
from either side of the TV.
Do not place the woofer unit on top of the
TV.
When the TV is used on a TV stand or
table, do not place the woofer unit
underneath the TV.
E
X
T
-
1
EXT-
4
E
X
T
-
2
S
E
X
T
-
3
S
A
U
D
IO
O
U
T
L
P
r
Pb
R
L
Y
R
Lever
HV-36P38SUE_Eng.book Page 5 Friday, September 26, 2003 11:10 AM
6
Setting up your TV
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Connecting the power cord to
the AC outlet
Caution
Operate only from the power source specified
(AC 220 – 240 V, 50 Hz) on the unit.
Putting the batteries into the
Remote control
Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.
Follow the warnings printed on the
batteries.
Battery life is about six months to one
year, depending on your frequency of use.
The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as necessary.
If the remote control does not work
properly, replace the batteries.
Initial settings
When the TV is first turned on, it enters the
initial setting mode, and the JVC logo is
displayed. Follow the instructions on the on-
screen display to make the initial settings.
1 Press the Main power button on the
TV
The Power lamp lights red (for power on),
then green (for TV on) and the JVC logo
is displayed.
If the power lamp stays red and does
not change to green:
Your TV is in the standby mode. To
turn the TV on, set the VCR/TV/DVD
switch on the remote control to the TV
position and press the # button. (See
page 13.)
Yellow button
Blue button
7 button
s
Main power
button
Power lamp
HV-36P38SUE
Main power
button
Power lamp
HV-32P37SUE/HV-28P37SUE
HV-36P38SUE_Eng.book Page 6 Friday, September 26, 2003 11:10 AM
8
Setting up your TV
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
6 Press the a
aa
a button to display the
T-V LINK menu
If you do not have a T-V LINK
compatible VCR connected:
Press the b button to exit the T-V LINK
menu.
The T-V LINK menu disappears.
If you have a T-V LINK compatible
VCR connected to the EXT-2
terminal:
Follow the operating procedure
“Downloading the data to VCR” on
page 9 to transmit the Programme number
(PR) data.
Now, the initial settings are complete,
and you can watch the TV
When your TV can detect the TV channel
name from the TV channel broadcast
signal, it automatically registers the TV
channel name (ID) to the Programme
number (PR) in which the TV channel has
been registered.
If a TV channel you want to view is not
set to a Programme number (PR),
manually set it using the MANUAL
function. For details, see “EDIT/
MANUAL” on page 32.
The TV channel is not registered in
Programme number PR 0 (AV). When
you want to register a TV channel to PR 0
(AV), manually set it using the
MANUAL function. For details, see
“EDIT/MANUAL” on page 32.
ACI function
This TV has an ACI function which decodes
the ACI (Automatic Channel Installation)
data.
Using the ACI function allows all TV
channels transmitted from the cable TV
station to be properly registered quickly
according to the data from the cable TV
station.
If “ACI START/ACI SKIP” appears in
the AUTO PROGRAM menu:
You can use the ACI (Automatic Channel
Installation) function to decode the ACI data
and complete the registration of all the TV
channels in a short period of time.
Press the 6
66
6 buttons to choose ACI
START. Then press the a
aa
a button to
start the ACI function
Depending on your cable TV station, there
may be a broadcast selection menu set up by
the cable TV station.
Follow the menu indications and use the
5 and 6 buttons to operate the menu.
After you have made the setting, press the
a button.
If you have any questions about the items
in the Broadcast Selection menu or how to
operate the menu, please contact your
cable TV station.
If you don’t want to use the ACI function,
press the 6 buttons to choose ACI
SKIP and then press a.
When the cable TV broadcast reception is
poor, the ACI function will not work
properly.
If there is an error in the ACI data itself,
the TV channel cannot be registered
properly. If this happens, turn the ACI
function off (ACI SKIP) and use the
AUTO PROGRAM function.
Alternatively, use the EDIT/MANUAL
function to correct the Programme
number (PR) setting.
D0005-EN
DOWNLOAD TV VCR
T-V LINK
OK
EXIT
HV-36P38SUE_Eng.book Page 8 Friday, September 26, 2003 11:10 AM
Setting up your TV
9
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
If “ACI ERROR” is displayed in the
AUTO PROGRAM menu:
“ACI ERROR” denotes that the ACI function
is not working properly. Press the 2 button
to start the ACI function again.
If “ACI ERROR” still appears even after you
have tried to start the ACI function several
times, press the 3 button to start the AUTO
PROGRAM function. It does not cause any
problem because all the TV channels are
registered to the Programme numbers (PR)
by the AUTO PROGRAM function.
Downloading the data to VCR
You can transmit to the latest Programme
numbers (PR) data to the VCR with the T-V
LINK function.
Caution
Only when the T-V LINK compatible
VCR is connected to the EXT-2
terminal, this operation is enabled.
Only when the T-V LINK menu is being
displayed, this operation is enabled.
1 Turn on the VCR
2 Press the a
aa
a button
The data transmission begins.
The T-V LINK menu disappears once the
data transmission ends.
When the T-V LINK menu is
changed over to another menu:
The TV has finished its menu. This new
menu is operated from the VCR. See the
VCR instruction manual for what to do
next.
If “FEATURE NOT AVAILABLE”
appears at the T-V LINK menu:
Check the following three items. Then
press the 2
22
2 button to retry data
transmission.
Has the T-V LINK compatible VCR
been connected to the EXT-2
terminal?
Has the VCR power been turned on?
Does the SCART cable that is
connected to the EXT-2 terminal to T-
V LINK compatible VCR have all
proper connections?
T-V LINK FUNCTIONS
When a T-V LINK compatible VCR is
connected to the EXT-2 Terminal on the TV,
it is easier to set up the VCR and to view
videos. T-V LINK uses the following
features:
To use T-V LINK functions:
A T-V LINK compatible VCR is necessary.
The VCR must be connected to the EXT-2
terminal on the TV by a fully wired SCART
cable.
A “T-V LINK compatible VCR” means a
JVC VCR with the T-V LINK logo or a VCR
with one of the following logos. However,
these VCRs may support some or all of the
features described below. For details, refer to
your VCR instruction manual.
“Q-LINK” (a trademark of Panasonic
Corporation)
“Data Logic” (a trademark of Metz
Corporation)
“Easy Link” (a trademark of Phillips
Corporation)
“Megalogic” (a trademark of Grundig
Corporation)
“SMARTLINK” (a trademark of Sony
Corporation)
D0005-EN
DOWNLOAD TV VCR
T-V LINK
OK
EXIT
D0037-EN
TRANSFER. . . . .
DOWNLOAD TV VCR
HV-36P38SUE_Eng.book Page 9 Friday, September 26, 2003 11:10 AM
11
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
TV buttons and functions
Refer to the pages in parentheses for details.
1 Remote control sensor
2 Power lamp (pages 6, 12)
3 Main power button (pages 6, 12)
4 Headphone jack (mini jack) (page 40)
5 P p buttons/ q buttons (page 12)
6 r (Volume) button (page 12)
7 EXT-5 terminal (pages 37, 40)
Refer to the pages in parentheses for details.
1 Remote control sensor
2 Power lamp (pages 6, 12)
3 Main power button (pages 6, 12)
4 Headphone jack (mini jack) (page 40)
5 P p buttons/ q buttons (page 12)
6 r (Volume) button (page 12)
7 EXT-5 terminal (pages 37, 40)
R
P
L
S
EXT-5
R
P
L
S
EXT-5
HV-36P38SUE
R
L
S
P
E
X
T
5
R
L
S
P
E
X
T
5
EXT-1
EXT-
4
EXT-2
S
EXT-3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
HV-32P37SUE/HV-28P37SUE
HV-36P38SUE_Eng.book Page 11 Friday, September 26, 2003 11:10 AM
12
TV buttons and functions
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Turn the Main power on
Press the Main power button on the
TV.
The Power lamp lights red and your TV is in
the standby mode.
If the Power lamp lights green, the TV is
already on.
To turn the Main power off:
Press the Main power button again.
The Power lamp goes off.
Caution
The main power button on the TV does
not fully isolate the TV from the AC
supply. If you are not going to use this TV
for a long period of time, be sure to
disconnect the AC plug from the AC
socket.
Turn the TV on from standby
mode
Press the P p
pp
p buttons to turn the TV
on from standby mode
Choose a TV channel
Press the P p
pp
p buttons to choose a
programme number (PR) or an EXT
terminal
Adjust the volume
1 Press the r
rr
r (Volume) button
The volume level indicator appears.
2 Press the q
qq
q buttons while the
volume level indicator is displayed
HV-36P38SUE_Eng.book Page 12 Friday, September 26, 2003 11:10 AM
13
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Remote control buttons and functions
1 Muting button
2 Number buttons
3 Information button
4 c button
5 3 sound button
6 b button
7 7 buttons
8 g (Text) button
9 p p buttons
0 VCR/DVD/Teletext control buttons
- p buttons
= # (Standby) button
~ VCR/TV/DVD switch
! G button
@ Colour button
# X (Multi) button
$ f/g (Freeze/Swap) button
% H button
^ a button
& b button
* r (Volume) q buttons
Turn the TV on or off from
standby mode
Press the #
##
# (Standby) button to turn
the TV on or off.
When the TV is turned on, the power lamp
changes from red to green.
The power can be turned on by pressing
the b button, p p buttons or Number
buttons.
=
~
0
3
4
5
9
6
7
8
-
#
!
^
&
@
*
$
%
1
2
To turn the TV on or off, set the VCR/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the VCR/TV/DVD switch on the remote
control is set to a position other than TV,
the TV will not be turned on or off even if
the # button is pressed.
HV-36P38SUE_Eng.book Page 13 Friday, September 26, 2003 11:10 AM
14
Remote control buttons and functions
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Choose a TV channel and
watch images from external
devices
If the picture is tilted, correct it. See
“PICTURE TILT” on page 36.
Use the number buttons:
Enter the programme number (PR)
of the channel using the number
buttons.
Example:
•PR 6 press 6
PR 12 press 1 and 2
Use the p
pp
p p
pp
p buttons:
Press the p
pp
p p
pp
p buttons to
choose the programme number
(PR) you want or an EXT terminal.
Use the AV button:
Press the AV button to choose an
EXT terminal.
You can choose a video input signal
from the S-VIDEO signal (Y/C signal)
and regular video signal (composite
signal). For details, see “S-IN (S-
VIDEO input)” on page 37.
If you do not have a clear picture or no
colour appears, change the colour
system manually. See “COLOUR
SYSTEM” on page 26.
If you choose an EXT terminal with no
input signal, the EXT terminal number
becomes fixed on the screen.
This TV set has a function which can
automatically change over the input
according to a special signal output
from an external device. (The EXT-4
and EXT-5 terminals do not support
this function.)
Since this TV is designed to make full
use of the resolution of the original
video source, the motion may appear
unnatural when the video source is
input with 625p progressive-scanning
component signals.
If this occurs, change the output setting
of the connected device to 625i
interlace-scanning component signal
output.
To return to a TV channel:
Press the b button, the p
p
buttons or
the Number buttons.
To use the Programme number PR 0
(AV):
When the TV and VCR are connected only
by the Aerial cable, choosing the Programme
number PR 0 (AV) allows you to view
images from the VCR. Set the VCR RF
channel to the Programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL” on page 32.
Pressing the G button changes the choice as
follows:
The VCR RF channel is sent as the RF
signal from the VCR.
Also refer to your VCR instruction
manual.
EXT-1
EXT-5
EXT-2
EXT-4
EXT-3
E3
S3
TV mode EXT modes
Programme
numbers
PR 1 – PR 99
or
or
or
EXT-1
EXT-5
EXT-2
EXT-4
EXT-3
E3
S3
TV mode
EXT modes
Programme
numbers
PR 1 – PR 99
or
PR 0
or
or
HV-36P38SUE_Eng.book Page 14 Friday, September 26, 2003 11:10 AM
16
Remote control buttons and functions
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
ZOOM function
You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.
AUTO:
When a WSS (Wide Screen Signalling)
signal, which shows the aspect ratio of the
picture, is included in the broadcast signal or
the signal from an external device, the TV
automatically changes the ZOOM mode to
16:9 ZOOM mode or FULL mode according
to the WSS signal.
If a WSS signal is not included, the picture is
displayed in accordance with the ZOOM
mode set with the 4:3 AUTO ASPECT
function.
For details of the 4:3 AUTO ASPECT
function, see “4:3 AUTO ASPECT” on
page 27.
When the AUTO (WSS) mode does not
function correctly due to poor WSS signal
quality or when you want to change the
ZOOM mode, press the c button
and change to another ZOOM mode.
REGULAR:
Use to view a normal picture (4:3 aspect
ratio) as its original size is.
PANORAMIC:
This mode stretches the left and right sides of
a normal picture (4:3 Aspect Ratio) to fill the
screen, without making the picture appear
unnatural.
The top and bottom of the picture are
slightly cut off.
14:9 ZOOM:
This mode zooms up the Wide Picture (14:9
Aspect Ratio) to the upper and lower limits
of the screen.
16:9 ZOOM:
This mode zooms up the Wide Picture (16:9
Aspect Ratio) to the full screen.
16:9 ZOOM SUBTITLE:
This mode zooms up the Wide Picture (16:9
Aspect Ratio) with subtitles to the full
screen.
FULL:
This mode uniformly stretches the left and
right sides of a normal picture (4:3 aspect
ratio) to fill the wide TV screen.
Use for pictures with a 16:9 aspect ratio that
have been squeezed into a normal picture
(4:3 aspect ratio), you can restore their
original dimensions.
Choose the ZOOM mode
1 Press the c
cc
c button to display
the ZOOM menu
•The c button does not work in
the twin pictures mode.
D0009-EN
AUTO
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL
ZOOM
OK
HV-36P38SUE_Eng.book Page 16 Friday, September 26, 2003 11:10 AM
18
Remote control buttons and functions
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
To cancel the FREEZE function:
Press the f button, the p p buttons or
the number buttons.
The FREEZE function does not work
while a sub-picture is displayed.
The still picture cannot be output from
the TV.
The FREEZE function does not work
for pictures of 625p, 525p and 1125i
signals.
Using the MULTI-PICTURE
function
1 Press the X
XX
X button
The MULTI-PICTURE menu appears.
2 Press the 5
55
5 buttons to choose
the number of screens and then
press the a
aa
a button
2-pictures multi:
12-pictures multi:
When set to 2-pictures multi, you can
view a TV picture and a picture from
an external device. You can not view a
TV picture on more than one screen at
the same time.
When 12-pictures multi is set, pictures
from external devices are not
displayed.
When set to 2-pictures multi, the main-
picture can be changed by pressing the
p p buttons. The sub-picture screen
can be changed by pressing the p
buttons.
When set to 12-pictures multi and
there are more than 12 pictures, the
next or previous 12 screens can be
displayed by pressing the p buttons.
When set to 2-pictures multi, press the
g (swap) button to switch the main-
picture and sub-picture.
2-pictures multi function does not
work for a picture of 1125i signal.
A picture of 625p or 525p signal
cannot be displayed as the sub-picture.
Pay attention to the following.
- When the EXT-4 picture is a picture
of 625p or 525p signal, you cannot
choose EXT-4 with the p buttons.
- When the EXT-4 picture signal is
changed to 625p, 525p or 1125i
signal while the EXT-4 picture is
displayed as the sub-picture, the 2-
pictures multi function is cancelled.
1
D0101-EN
212
D0102
1
D0103
2
D0104
12
Choose to return to one screen.
Choose to change to 2-pictures multi.
Choose to change to 12-pictures multi.
D0056-EN
Main-
picture
Sub-
picture
D0058-EN
Still
pictures
Moving
picture
Changing the sub-picture
Displaying the next or
previous 12 screens
HV-36P38SUE_Eng.book Page 18 Friday, September 26, 2003 11:10 AM
Remote control buttons and functions
19
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
- The pictures cannot be swapped
when a picture of 625p or 525p
signal from EXT-4 is being
displayed as the main picture.
Do not press the g (swap) button
while you are recording the TV output
on the VCR. If you do, the TV output
signal will change.
You cannot view a scrambled channel
in the sub-picture. If the g (swap)
button is pressed when viewing a
scrambled channel in the main-picture
using an external decoder, the channel
you have been viewing in the sub-
picture will appear in both the main-
picture and sub-picture.
When set to 2-pictures multi and the
headphones are connected, the sound
for the main-picture is output from the
TV speakers and the sound from the
sub-picture is output from the
headphones.
- Adjust the volume of the sub-picture
sound from the headphones with
“HEADPHONE VOLUME” in the
“SOUND” menu (see page 28).
- The main-picture sound can not be
heard through the headphones.
When set to 12-pictures multi, press
the 7 buttons to choose the
screen you want to view and the press
the a button to display that picture
on the whole screen.
The BLUE BACK function does not
work when the MULTI-PICTURE
function is being used.
The ZOOM function does not work
when the MULTI-PICTURE function
is being used.
To return the multi-picture to one
screen:
Press the M button, press the 5
buttons to choose one screen, and then
press the a button.
Pressing the b button will also return
the display to one screen.
Operating a JVC brand VCR or
DVD player
You can operate a JVC brand VCR or DVD
player. Pressing the button having the same
appearance as the original remote control
button of a device makes the function work
in the same way as the original remote
control.
1 Set the VCR/TV/DVD Switch to the
VCR or DVD position
VCR:
When you are operating the VCR, set the
switch to the VCR position.
You can turn the VCR on or off with
the # (Standby) button.
DVD:
When you are operating the DVD player,
set the switch to the DVD position.
You can turn the DVD player on or off
with the # (Standby) button.
2 Press the VCR/DVD Control Button
to control your VCR or DVD player
If your device is not made by JVC,
these buttons cannot be used.
Even if your device is made by JVC,
some of these buttons or any one of the
buttons may not work, depending on
the device.
You can use the p buttons to choose
a TV channel. The VCR will receive or
choose the chapter the DVD player
plays back.
Some DVD player models use the p
buttons for both operating of Fast
forward/backward functions and
choosing the chapter. In this case, the
253 buttons do not work.
You cannot turn the TV on or off when the
VCR/TV/DVD switch is set to the VCR or
DVD position.
When you turn the TV on or off, set the
VCR/TV/DVD switch to the TV position.
HV-36P38SUE_Eng.book Page 19 Friday, September 26, 2003 11:10 AM
20
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Teletext function
Basic operation
You can view three types of teletext
broadcasts on the TV:
FLOF (Fastext), TOP and WST.
1 Choose a TV channel with a teletext
broadcast
2 Set the VCR/TV/DVD switch to the
TV position
3 Press g
gg
g (Text) button to display
the teletext
Pressing g (Text) button changes the
mode as follows:
4 Choose a teletext page by pressing
the p
pp
p p
pp
p buttons, Number buttons
or Colour buttons
To return to the TV mode:
Press the b button or g (Text) button.
If you have trouble receiving teletext
broadcasts, consult your local dealer or
the teletext station.
The ZOOM function will not operate
in the TV and text mode or Text mode.
No menu operations are possible when
viewing a teletext programme.
Language display depends on the
country which was set on the
COUNTRY menu. If characters on a
Teletext programme do not appear
properly, change the COUNTRY
setting to other country’s. To change
the COUNTRY setting, perform steps
1 and 2 of the “AUTO PROGRAM”
procedure on page 32 and then press
the a button.
Using the List Mode
You can store the numbers of your favourite
teletext pages in memory and call them up
quickly using the colour buttons.
To store the page numbers:
1 Press B
BB
B button to engage the
List mode
The stored page numbers are displayed at
the bottom of the screen.
2 Press a Colour button to choose a
position. Then press the Number
buttons to enter the page number
VCR/TV/
DVD
TV mode
TV and text mode
Text mode
HV-36P38SUE_Eng.book Page 20 Friday, September 26, 2003 11:10 AM
Teletext function
21
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
3 Press and hold down A
AA
A (Store)
button
The four page numbers blink white to
indicate that they are stored in memory.
To call up a stored page:
1 Press the B
BB
B button to engage
the List mode
2 Press a colour button to which a
page has been assigned
To exit the List mode:
Press the B button again.
Hold
You can hold a teletext page on the screen for
as long as you want, even while several other
teletext pages are being received.
Press the C
CC
C (Hold) button
To cancel the Hold function:
Press C (Hold) button again.
Sub-page
Some teletext pages include sub-pages that
are automatically displayed.
1 Choose a teletext page that
includes sub-pages
Sub-page numbers that can be viewed are
automatically displayed at the top of the
screen.
2 Press the 5
55
5 buttons to choose a
sub-page number
Reveal
Some teletext pages include hidden text
(such as answers to a quiz).
You can display the hidden text.
Each time you press the E
EE
E (Reveal)
button, text is hidden or revealed
Size
You can double the height of the teletext
display.
Press the F
FF
F (Size) button
Index
You can return to the index page instantly.
Press G
GG
G (Index) button
Returns to page 100 or a previously specified
page.
Hold indication
HV-36P38SUE_Eng.book Page 21 Friday, September 26, 2003 11:10 AM
22
Teletext function
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Cancel
You can search for a teletext page while
watching TV.
1 Press the Number button to enter a
page number, or press a Colour
button
The TV searches for a teletext page.
2 Press H
HH
H (Cancel) button
The TV programme appears. When the
TV finds the teletext page, its page
number appears in the upper left of the
screen.
3 Press H
HH
H (Cancel) button to return
to a teletext page when the page
number is on the screen
The TV mode cannot be resumed even
by pressing the H (Cancel) button. A
TV programme is temporarily
displayed instead of the teletext
programme.
HV-36P38SUE_Eng.book Page 22 Friday, September 26, 2003 11:10 AM
23
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Using the TV’s menu
This TV has a number of functions which
you can operate using menus. To fully utilize
your TV’s functions, you need to fully
understand the basic menu operating
techniques.
Buttons used to operate the menus
Basic operation
1 Press the H
HH
H button to display
the menu bar
2 Press the 5
55
5 buttons to choose
the menu you want to use and then
press the a
aa
a button
3 Press the 6
66
6 buttons to choose
the item to be set, press the 5
55
5
buttons to set the item, and then
press the a
aa
a button
If there are sub-menus, use the 7
buttons to operate them.
Press the b button to return to
the previous menu.
Press the b or H button to exit
from the menu.
Types of menu
The menu guide area can be made to appear
and disappear for some menus.
While the menu is displayed, press the h
button to change between the guide area
being displayed and not displayed.
The guide area for some menus will still
be displayed even if the h button is
pressed. This is not a malfunction.
D0105-EN
PICTURE
D1105-EN
PICTURE
Chosen
menu name
Chosen
menu
PICTURE menu
Choose to set the screen
settings.
SOUND menu
Choose to set the sound settings.
FEATURES menu
Choose to set the sleep timer
and child lock settings.
SET UP menu
Choose to edit the channels or
set the display language
settings.
D0106
D0107
D0108
D0109
D0017-EN
>> 4:3 AUTO ASPECT
OK
PANORAMIC
REGULAR
14:9 ZOOM
D1017-EN
>> 4:3 AUTO ASPECT
PANORAMIC
REGULAR
14:9 ZOOM
Guide area
HV-36P38SUE_Eng.book Page 23 Friday, September 26, 2003 11:10 AM
24
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
PICTURE menu
While the PICTURE menu is displayed,
pressing the blue button will set the
CONTRAST, BRIGHT, SHARP,
COLOUR, HUE settings to their default
settings.
PICTURE MODE
You can choose one of three PICTURE
MODEs to adjust the picture settings
automatically.
BRIGHT:
Heightens contrast and sharpness.
STANDARD:
Standardizes picture adjustment.
SOFT:
Softens contrast and sharpness.
CONTRAST
You can adjust the picture contrast.
2 :lower
3 : higher
BRIGHT
You can adjust the picture brightness.
2 : darker
3 : brighter
SHARP
You can adjust the picture sharpness.
2 : softer
3 :sharper
COLOUR
You can adjust the picture colour.
2 : lighter
3 :deeper
HUE
You can adjust the picture tint.
2 : reddish
3 :greenish
You can change the HUE setting (picture
hue) when the colour system is NTSC
3.58, NTSC 4.43.
COLOUR TEMP.
You can select one of three COLOUR
TEMP. modes (three tones of white) to adjust
the white balance of the picture. Since white
is the colour which is used as a reference for
all the other colours, changing the COLOUR
TEMP. mode affects the appearance of all
the other colours on the screen.
COOL:
A bluish white. Using this mode when
watching bright pictures allows you to enjoy
a more vivid and bright picture.
NORMAL:
The normal white colour.
WARM:
A reddish white. Using this mode when
watching films allows you to enjoy colours
that are characteristic of films.
PICTURE MODE
CONTRAST
BRIGHT
SHARP
COLOUR
HUE
COLOUR TEMP.
FEATURES
COOL
STANDARD
PICTURE
D0014-EN
OK
RESET
HV-36P38SUE_Eng.book Page 24 Friday, September 26, 2003 11:10 AM
PICTURE menu
25
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
FEATURES
Choose FEATURES and press the a or 3
button to display the sub-menu.
DIGITAL VNR
The DIGITAL VNR function cuts down the
amount of noise in the original picture.
You can choose from the four DIGITAL
VNR function settings of AUTO(LOW),
AUTO(HIGH), MIN and MAX.
AUTO(LOW)/AUTO(HIGH):
The TV will automatically adjust the level of
the DIGITAL VNR effect to match the
amount of noise in the picture, giving you the
best possible picture.
If you set the DIGITAL VNR effect too
high it can make the picture less sharp. It
is recommended to use the AUTO(LOW)
setting if you can. If you set the DIGITAL
VNR function to AUTO(LOW)but still
notice some noise, change the setting
from AUTO(LOW) to AUTO(HIGH).
MIN:
The level of the DIGITAL VNR effect is set
to the minimum. If you set the DIGITAL
VNR function to AUTO(LOW) but feel that
the sharpness of the original picture has not
been reproduced fully, change the setting
from AUTO(LOW) to MIN.
The MIN setting is not suitable for low-
quality pictures which contain a lot of
noise.
MAX:
The level of the DIGITAL VNR effect is set
to the maximum. If you set the DIGITAL
VNR function to AUTO(HIGH) but still
notice some noise, change the setting from
AUTO(HIGH) to MAX.
The MAX setting is not suitable for high-
quality pictures which contain very little
noise.
Super DigiPure
The Super DigiPure function uses the latest
in digital technology to give you a natural-
looking picture. The Super DigiPure function
includes the following two functions.
DigiPure function:
This function helps to create a natural-
looking picture by eliminating unnecessary
edges from high-contrast and crisp images.
For images with low-contrast, edges are
added to produce a sharper, more detailed
picture.
You can choose from the three DigiPure
function settings of AUTO, MIN and MAX.
If you set the DigiPure effect too high on
a low-quality picture that contains a lot of
noise, this may actually make the noise
worse. We recommend you use the
AUTO setting if you can.
Picture motion compensation
function:
This function displays fast-moving pictures
(for example, the players or ball in a football
game) more smoothly and naturally on the
screen.
The effect level of the picture motion
compensation function cannot be
changed. The effect level is the same no
matter which of the AUTO, MIN or MAX
settings is used.
AUTO:
The TV will automatically adjust the level of
the DigiPure effect to match the amount of
noise in the picture, giving the best possible
picture.
D1015-EN
DIGITAL VNR
Super DigiPure
MOVIE THEATRE
Colour DigiPure
COLOUR SYSTEM
4:3 AUTO ASPECT
AUTO(LOW)
AUTO
AUTO
> FEATURES
ON
OK
HV-36P38SUE_Eng.book Page 25 Friday, September 26, 2003 11:10 AM
26
PICTURE menu
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
MIN:
The level of DigiPure effect is set to the
minimum. When you set the Super DigiPure
function to AUTO and notice some noise,
change the setting from AUTO to MIN.
The MIN setting is not suitable for high-
quality pictures which contain very little
noise.
MAX:
The level of DigiPure effect is set to the
maximum. If you set the Super DigiPure
function to AUTO but feel that the original
picture quality has not been reproduced fully,
change the setting from AUTO to MAX.
The MAX setting is not suitable for low-
quality pictures which contain a lot of
noise.
OFF:
The Super DigiPure function is turned off.
MOVIE THEATRE
The MOVIE THEATRE function displays a
cinema film picture more smoothly and
naturally on the screen.
AUTO:
The television automatically recognizes the
type of signal and turns the function on and
off.
ON:
This function is turned on.
OFF:
This function is turned off.
The motion may appear unnatural when
viewing images with the NTSC colour
system. When the MOVIE THEATRE
function is set to AUTO or ON, the
motion may appear unnatural when
viewing images with the NTSC colour
system.
Colour DigiPure
Makes the colour outline stand out and
increases the sharpness giving a clearer
picture.
ON:
Colour DigiPure works. Normally use with
this function turned on.
OFF:
Colour DigiPure doesn't work. This gives a
less clear picture than when this function is
turned on.
COLOUR SYSTEM
The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.
1 Choose COLOUR SYSTEM. Then
press the a
aa
a or 3
33
3 button
The sub-menu of the COLOUR SYSTEM
function appears.
2 Press the 5
55
5 buttons to choose
MAIN or SUB
MAIN:
You can change the colour system of the
main-picture.
SUB:
You can change the colour system of the
sub-picture.
Choose MAIN when a sub-picture is
not displayed.
3 Press the 6
66
6 buttons to choose
the appropriate colour system.
Then press the a
aa
a button
PAL:
PAL system
SECAM:
SECAM system
NTSC 3.58:
NTSC 3.58 MHz system
NTSC 4.43:
NTSC 4.43 MHz system
D0016-EN
>> COLOUR SYSTEM
MAIN
SUB
PAL
AUTO
OK
HV-36P38SUE_Eng.book Page 26 Friday, September 26, 2003 11:10 AM
PICTURE menu
27
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
AUTO:
This function detects a colour system
from the input signal. You can only use
this when you are viewing a picture from
programme number PR 0 (AV), or an
EXT terminal.
The AUTO function may not function
properly if you have poor signal quality.
If the picture is abnormal in the AUTO
function, choose another colour system
manually.
When in the Programme numbers PR 0
(AV) to PR 99, you cannot choose NTSC
3.58 or NTSC 4.43.
“COLOUR SYSTEM” cannot be chosen
when you are watching the EXT-4
picture.
4:3 AUTO ASPECT
You can choose one of three ZOOM modes,
REGULAR, PANORAMIC or 14:9 ZOOM,
as the ZOOM mode for the normal picture
(4:3 aspect ratio).
1 Choose 4:3 AUTO ASPECT then
press the a
aa
a button
2 Press the 6
66
6 buttons to choose a
ZOOM mode
D0017-EN
>> 4:3 AUTO ASPECT
OK
PANORAMIC
REGULAR
14:9 ZOOM
HV-36P38SUE_Eng.book Page 27 Friday, September 26, 2003 11:10 AM
28
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
SOUND menu
Functions in the “SOUND” menu other
than “HEADPHONE VOLUME” work
for the TV speakers. They do not work for
the sound from the headphones.
When the headphones are connected and
only one screen is displayed, only
“HEADPHONE VOLUME” can be used.
STEREO / I • II
When you are viewing a bilingual broadcast
programme, you can choose the sound from
Bilingual I (Sub I) or Bilingual II (Sub II).
When the stereo broadcasting is received
poorly, you can change from stereo to mono
sound so that you can hear the broadcast
more clearly and easily.
The sound mode you can choose differs
depending on the TV programme.
This function does not work in the EXT
modes.
BASS
You can adjust the low tone of the sound.
2 : weaker
3 :strong
TREBLE
You can adjust the high tone of the sound.
2 : weaker
3 :strong
BALANCE
You can adjust the volume balance between
the left and right speaker.
2 : turn the left speaker’s volume level up.
3 : turn the right speaker’s volume level up.
HEADPHONE VOLUME
Adjust the volume of the sub-picture sound
which is heard through the headphones when
set to 2-pictures multi.
2 : Reduce volume
3 : Increase volume
When not set to 2-pictures multi, the
headphone volume is adjusted with the
r q (volume) buttons.
3D CINEMA SOUND
Press the 3 button to set the 3D CINEMA
SOUND effect when 3D CINEMA SOUND
is set to ON or MONO.
Choose 3D CINEMA SOUND. Then
press the a
aa
a or 3
33
3 button to display
the sub-menu.
SURROUND
Adjust the surround effect.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the surround
effect and choosing HIGH will increase the
surround effect.
BASS BOOST
Adjust the bass sound.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the bass sound
and choosing HIGH will increase the bass
sound.
s: Stereo sound
v : mono sound
t : Bilingual I (sub I)
u : Bilingual II (sub II)
D0019-EN
STEREO/
BASS
TREBLE
BALANCE
HEADPHONE VOLUME
3D CINEMA SOUND
SOUND
OK
D0111-EN
SURROUND
BASS BOOST
> 3D CINEMA SOUND
OK
MID
MID
HV-36P38SUE_Eng.book Page 28 Friday, September 26, 2003 11:10 AM
29
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
FEATURES menu
SLEEP TIMER
You can set the TV to automatically turn off
after a specified period of time.
1 Choose SLEEP TIMER. Then press
the a
aa
a or 3
33
3 button
A Sub-menu of the SLEEP TIMER
function appears.
2 Press the 5
55
5 buttons to set the
period of time.
Then press the a
aa
a button
You can set the period of time a
maximum of 120 minutes (2 hours) in 10
minute increments.
One minute before the SLEEP TIMER
function turns off the TV, “GOOD
NIGHT!” appears.
The SLEEP TIMER function cannot
be used to turn off the TV’s main
power.
When the SLEEP TIMER function is
on, you can display the Sub-menu of
the SLEEP TIMER function again to
confirm and/or change the remaining
period of time of the SLEEP TIMER
function. Press the a button to exit
the menu after confirming and / or
changing the remaining time.
To cancel the SLEEP TIMER
function:
Press the 2 button to set a period of time
to “OFF”.
CHILD LOCK
When there is a TV channel you wish your
children not to watch, you can use the
CHILD LOCK function to lock out the TV
channel. Even when a child chooses a
Programme number (PR) in which a locked
TV channel has been registered, the screen
will change to blue and displays n (CHILD
LOCK) so the TV channel cannot be viewed.
Unless you enter a pre-set ID number by a
special operation, the lock cannot be released
and the child cannot view the TV channel
programmes.
To set the CHILD LOCK function
1 Choose CHILD LOCK, then press
the 0
00
0 button
“SET ID NO.” (ID number setting screen)
appears.
2 Set the ID number to your liking
1 Press the 6
66
6 buttons to choose
a number.
2 Press the 5
55
5 buttons to move
the cursor.
D0023-EN
SLEEP TIMER
CHILD LOCK
APPEARANCE
BLUE BACK
TYPE A
ON
FEATURES
OK
D0024-EN
OFF
0120
> SLEEP TIMER
OK
D0025-EN
>> SET ID NO.
0
040
OK
HV-36P38SUE_Eng.book Page 29 Friday, September 26, 2003 11:10 AM
30
FEATURES menu
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
3 Press the a
aa
a button
The Sub-menu of CHILD LOCK appears.
4 Press the 6
66
6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
Programme number (PR) changes, and the
picture of the TV channel registered in the
Programme number (PR) is displayed on
the screen.
5 Press the blue button and set the
CHILD LOCK function.
Then press the a
aa
a button
n (CHILD LOCK) appears and the TV
channel is locked.
To reset the CHILD LOCK function:
Press the blue button again.
n (CHILD LOCK) disappears.
To disable easy resetting of the CHILD
LOCK function, the menu disappears by
choosing the CHILD LOCK function and
pressing the a button as in the ordinary
menu operation.
To view a locked TV channel
1 Choose a Programme number (PR)
in which a TV channel locked with
the Number buttons or PR LIST
The screen changes to blue and the n
(CHILD LOCK) appears. You cannot
view the TV channel.
2 Press the
h
hh
h
(Information) button to
display “ID NO.” (ID NO. input
screen)
3 Press the Number buttons to enter
the ID number
The lock is temporarily released so you
can view the TV channel.
If you have forgotten the ID
number:
Perform step 1 of “To set the CHILD
LOCK function”. After confirming the ID
number, press the b button to exit the
menu.
Even if you reset the lock temporarily,
it does not mean that the CHILD
LOCK function set for the TV channel
is cancelled. The next time anyone
attempts to view the TV channel, it
will be locked again.
When you would like to cancel the
CHILD LOCK function, you must
perform the operation “To set the
CHILD LOCK function” again.
To disable easy choosing of a
Programme number (PR) in which a
locked TV channel has been
registered, the Programme number
(PR) has been set that it cannot be
chosen by the 6 buttons or the
operation buttons at the TV.
To disable easy resetting of the lock,
“ID NO.” (ID NO. input screen) is set
so that it cannot appear unless you
press the
h
(Information) button.
D0026-EN
> CHILD LOCK
OK
LOCK
CH
PR ID
AV
01
02
03
04
05
06
07
08
09
CH/CC
BBC1
31
CH 31
CH
32
D0027-EN
5
D0028-EN
ID NO. :
5
HV-36P38SUE_Eng.book Page 30 Friday, September 26, 2003 11:10 AM
FEATURES menu
31
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
APPEARANCE
Press the 5 button and choose the format
in which the channel number is displayed
from the three types: TYPE A, TYPE B and
TYPE C.
BLUE BACK
You can set the TV to automatically change
to a blue screen and mute the sound if the
signal is weak or absent, or when there is no
input from an external device.
ON:
This function is turned on.
OFF:
This function is turned off.
HV-36P38SUE_Eng.book Page 31 Friday, September 26, 2003 11:10 AM
32
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
SET UP menu
AUTO PROGRAM
The AUTO PROGRAM function TV
channel automatic registration which was
performed in the “Initial settings” (page 6)
can be preformed again.
1 Choose AUTO PROGRAM, then
press the a
aa
a or 3
33
3 button
The COUNTRY menu appears as a sub-
menu of the AUTO PROGRAM function.
There are two COUNTRY menus.
Pressing the yellow button changes the
COUNTRY menu as follows:
2 Press the 5
55
5 and 6
66
6 buttons to
choose the country where you are
now located
3 Perform steps 5 and 6 of the “Initial
settings” (page 7).
EDIT/MANUAL
The EDIT/MANUAL functions are divided
into two types: editing of the current
Programme numbers (PR) (EDIT functions)
and manual registration of a TV channel you
want to view to the Programme number (PR)
(MANUAL function). The details about
these functions are as follows:
MOVE:
This function changes a Programme number
(PR) of a TV channel.
ID:
This function registers a Channel name (ID)
to a TV channel.
INSERT:
This function adds a new TV channel in the
current Programme numbers (PR) list by
using the CH/CC number.
You cannot use the INSERT function if
you do not know a Channel number of a
TV channel. Use the MANUAL function
to register a TV channel in the
Programme number (PR).
DELETE:
This function deletes an unnecessary TV
channel.
MANUAL:
This function manually registers a new TV
channel in a Programme number (PR).
Caution
Using the MOVE, DELETE or INSERT
function rewrites the current Programme
numbers (PR) list. Resultingly, the
Programme number (PR) of some of the
TV channels will change.
Using the MANUAL function for a TV
channel for which the CHILD LOCK
function has been set cancels the CHILD
LOCK function for the TV channel.
Using the MANUAL function for a TV
channel for which the DECODER (EXT-2)
function has been set to ON returns the
setting of the DECODER (EXT-2) function
for the TV channel to OFF.
When a TV channel has already been
registered in PR 99, using the INSERT
function deletes the TV channel.
D0029-EN
SET UP
AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
PICTURE TILT
DECODER(EXT-2)
EXT SETTING
OK
ON
MORE
START
D0003-EN
OK
MORE
START
OK
> COUNTRY
> COUNTRY
HV-36P38SUE_Eng.book Page 32 Friday, September 26, 2003 11:10 AM
SET UP menu
33
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Basic operation
1 Choose EDIT/MANUAL, then press
the a
aa
a or 3
33
3 button
The EDIT menu appears.
2 Follow the operation description of
a function you want to use and
operate the function
3 Press the a
aa
a button to complete
the settings
The T-V LINK menu appears.
If you do not have a T-V LINK
compatible VCR connected:
Press the b button to exit the T-V LINK
menu.
The T-V LINK menu disappears.
If you have a T-V LINK compatible
VCR connected to the EXT-2 terminal:
Follow the operating procedure
“Downloading the data to VCR” on page 9 to
transmit the Programme number (PR) data.
For Programme number PR 0, “AV”
appears in the Programme numbers (PR)
list.
An EXT terminal number does not appear
in the Programme numbers (PR) list.
The CH/CC number is a number unique to
the TV and corresponding to the Channel
number of a TV channel. For the
relationship of a Channel number and a
CH/CC number, see “CH/CC numbers”
on page 43.
MOVE
1 Press the 6
66
6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
Programme number (PR) is changed over,
and the picture of the TV channel
registered in the Programme number (PR)
appears on the screen.
2 Press the 3
33
3 button to start the
MOVE function
3 Press the 6
66
6 buttons to choose a
new Programme number (PR)
To cancel the MOVE function:
Press the b button.
4 Press the 2
22
2 button to change the
Programme number (PR) of a TV
channel to a new Programme
number (PR)
> EDIT
PR ID
AV
01
02
03
04
05
06
07
08
09
BBC1
31
32
D0038-EN
OK
DELETE
MANUAL
ID
MOVE
INSERT
CH/CC 31
CH/CC
CH/CC
CH/CC
D0005-EN
DOWNLOAD TV VCR
T-V LINK
OK
EXIT
D0030-EN
CHBBC1 31
> EDIT
OK
CH/CC
PR ID
AV
01
02
03
04
05
06
07
08
09
CH/CC 31
CH/CC
32
STORE
HV-36P38SUE_Eng.book Page 33 Friday, September 26, 2003 11:10 AM
34
SET UP menu
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
DELETE
1 Press the 6
66
6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
Programme number (PR) is changed over,
and the picture of the TV channel
registered in the Programme number (PR)
appears on the screen.
2 Press the yellow button to delete
the TV channel
The TV channel is deleted from the
Programme numbers (PR) list.
ID
1 Press the 6
66
6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
Programme number (PR) is changed over,
and the picture of the TV channel
registered in the Programme number (PR)
appears on the screen.
2 Press the red button to start the ID
function
3 Press the 6
66
6 buttons to choose
the first character of a Channel
name (ID) you want to attach to the
TV channel
4 Press the blue button to display the
ID LIST (channel name list)
5 Press the 6
66
6 buttons to choose
the Channel name (ID)
To cancel the ID function:
Press the b button.
6 Press the a
aa
a button to register a
Channel name (ID) to a TV channel
You can register your unique Channel
name (ID) to the TV channel. When
step 3 is completed, do not go to step
4, but press the 5 buttons to move
the cursor and the 6 buttons to
choose a character for completing the
Channel name (ID). Then press the
a button to register the Channel
name (ID) to the TV channel.
Before performing INSERT or
MANUAL operation
If you register the TV channel (SECAM-
L system) from a French station, be sure
to set the COUNTRY setting to
FRANCE. If the COUNTRY setting is
not set to FRANCE, perform steps 1 and 2
of the “AUTO PROGRAM” (page 32)
procedure and set the COUNTRY setting
to FRANCE before pressing the a
button.
A CH/CC number unique to this TV and
corresponding to the Channel number of a
TV channel is required. Find the
corresponding CH/CC number from a
table “CH/CC numbers” on page 43 based
on the Channel number of the TV
channel.
D0031-EN
> EDIT
OK
ID LIST
CH/CC
PR ID
AV
01
02
03
04
05
06
07
08
09
CH/CC
BBC1
31
CH/CC 31
CH/CC
32
D0032-EN
> EDIT
OK
ID LIST
CH/CC
PR ID
AV
01
02
03
04
05
06
07
08
09
CH/CC
BBC1
31
CH/CCM31
CH/CC
32
D0033-EN
ID LIST
M6
MBC
MCM
MDR
MOVIE
MTV
MTV3
> EDIT
OK
CH/CC
PR ID
AV
01
02
03
04
05
06
07
08
09
CH/CC
BBC1
31
CH/CCM31
CH/CC
32
HV-36P38SUE_Eng.book Page 34 Friday, September 26, 2003 11:10 AM
SET UP menu
35
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
When the COUNTRY setting is not
FRANCE, use a two-digit CH/CC
number. When the COUNTRY setting is
FRANCE, use a three-digit CH/CC
number.
INSERT
1 Press the 6
66
6 buttons to choose a
Programme number (PR) for which
you will register a new TV channel
2 Press the green button and start
the INSERT function
3 Press the 6
66
6 buttons to choose
“CC” or “CH” according to the CH/
CC number of the TV channel
When the COUNTRY setting is
FRANCE:
Choose “CH1”, “CH2”, “CC1” or “CC2”.
To cancel the INSERT function:
Press the b button.
4 Press the Number buttons to enter
the remaining CH/CC number
The TV shifts to registration mode.
When the registration is completed, the
picture of the TV channel appears on the
screen.
The CH/CC number is a number
indicating the broadcast frequency to
the TV. If the TV cannot detect the TV
channel corresponding to the broadcast
frequency indicated by the CH/CC
number, a picture in the no-signal state
appears.
MANUAL
1 Press the 6
66
6 buttons to choose a
Programme number (PR) to which
you want to register a new TV
channel
2 Press the blue button to activate
the MANUAL function
At the right side following the CH/CC
number, the SYSTEM (broadcasting
system) of the TV channel appears.
To cancel the MANUAL function:
Press the b button.
3 Press the 3
33
3 button to choose the
SYSTEM (broadcasting system) for
a TV channel you want to register
TV channel (SECAM-L system)
from a French station:
Set the SYSTEM to “L”. If it is set to one
other than “L”, you cannot receive the TV
channel of the SECAM-L system.
Other TV channels:
If you do not know the correct
broadcasting system, set the SYSTEM to
“B/G”. If “B/G” is not correct, it results in
the fact that you will not hear the sound
normally when the TV detects a TV
channel. In this case, retry to set the
SYSTEM again correctly so that no
problem arises.
4 Press the green or red button to
search for a TV channel
Scanning stops when the TV finds a TV
channel. Then the TV channel is
displayed.
D0034-EN
> EDIT
CH/CC
PR ID
AV
01
02
03
04
05
06
07
08
09
CH/CC
BBC1
31
CH/CC
CH/CC 31
09
CH/CC 32
OK
CH/CC
D0035-EN
> MANUAL
CH/CC
PR ID
AV
01
02
03
04
05
06
07
08
09
CH/CC
BBC1
31
CH/CC
32
OK
CH/CC 31
SYSTEM
FINE+
FINE-
SEARCH+
SEARCH-
(
B / G
)
HV-36P38SUE_Eng.book Page 35 Friday, September 26, 2003 11:10 AM
36
SET UP menu
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
5 Press the green or red button
repeatedly until the TV channel you
want appears
If the TV channel reception is poor:
Press the blue or yellow button to fine-
tune the TV channel.
If you cannot hear the normal
sound even when the picture of the
TV channel appears normally:
The SYSTEM setting is wrong. Press the
3 button and choose a SYSTEM that has
normal sound.
6 Press the a
aa
a button and register
the TV channel to a Programme
number (PR)
The normal EDIT menu is resumed.
LANGUAGE
The LANGUAGE setting which was
performed in the “Initial settings” (page 6)
can be changed.
1 Choose LANGUAGE, then press
the a
aa
a or 3
33
3 button
A sub-menu of the LANGUAGE function
appears.
2 Press the 5
55
5 and 6
66
6 buttons to
choose a language. Then press the
a
aa
a button
PICTURE TILT
There are cases where the Earth’s magnetic
force may make the picture tilt or make
unnatural colours appear in the corner of the
screen. If this happens, you can correct it.
1 Choose PICTURE TILT, then press
the a
aa
a or 3
33
3 button
The sub-menu of the PICTURE TILT
function appears.
2 Press the 6
66
6 buttons until the
picture becomes level. Then press
the a
aa
a button
DECODER (EXT-2)
When connecting a Decoder with a T-V
LINK compatible VCR connected to the
EXT-2 terminal, use the DECODER (EXT-
2) function to unscramble the scrambled TV
channels.
1 Turn on the Decoder power
2 Display the TV channel capable of
being unscrambled with the
Decoder on the TV
Even if the Decoder is functioning, a
scrambled picture appears at this time.
3 Display the SET UP menu and
choose DECODER (EXT-2)
D0002(E)-EN
> LANGUAGE
OK
D0018-EN
>> PICTURE TILT
OK
D0029-EN
SET UP
AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
PICTURE TILT
DECODER(EXT-2)
EXT SETTING
OK
ON
HV-36P38SUE_Eng.book Page 36 Friday, September 26, 2003 11:10 AM
SET UP menu
37
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
4 Press the 5
55
5 buttons to choose
ON
An unscrambled picture appears.
To cancel the DECODER (EXT-2)
function:
Press the 5 buttons to choose OFF.
5 Press the a
aa
a button to complete
the setting
The T-V LINK menu appears.
You can send the programme numbers
data to a VCR with the T-V LINK
function.
6 Turn on the VCR, and then press
the a
aa
a button to transmit the data
to VCR
The T-V LINKmenu disappears once the
data transmission ends.
7 If you have another TV channel
capable of being unscrambled with
a Decoder, repeat steps 2 through 6
If for some reason the DECODER (EXT-
2) function has been set to “ON” but the
TV channel cannot be unscrambled, check
the following:
Has the Decoder been connected to the
VCR properly according to the VCR
and Decoder Instruction Manuals?
Has the Decoder power been turned
on?
Can the TV channel be unscrambled
with a Decoder?
Is it necessary to change the VCR
settings in order to connect the
Decoder? Confirm that the VCR is set
properly by rechecking the VCR
Instruction Manual.
EXT SETTING
1 Choose EXT SETTING, then press
the a
aa
a or 3
33
3 button
The EXT SETTING menu appears.
2 Follow the operation description of
a function you want to use and
operate the function
S-IN:
You can enjoy high-quality picture of the
2 S-VIDEO signal (Y/C signal).
ID LIST:
You can have a name corresponding to
the devices connected for each EXT
terminal.
DUBBING:
You can choose a signal source to be
output from an EXT-2 terminal.
S-IN (S-VIDEO input)
When connecting a device (such as S-VHS
VCR) which enables an S-VIDEO signal (Y/
C signal) to be output, you can enjoy high-
quality picture of the S-VIDEO signal (Y/C
signal).
D0005-EN
DOWNLOAD TV VCR
T-V LINK
OK
EXIT
D0020-EN
S-IN
ID LIST
OK
EXT-1
EXT-3
DUBBING
EXT-2
EXT-4
EXT-5
TV
> EXT SETTING
HV-36P38SUE_Eng.book Page 37 Friday, September 26, 2003 11:10 AM
38
SET UP menu
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Preparation:
At first, read the Device Instruction
Manual and “Additional preparation” on
page 40 to connect the device to the TV
properly. Second, follow the Device
Instruction Manual to set the device so
that an S-VIDEO signal (Y/C signal) can
be output to the TV.
Do not set S-IN (S-VIDEO input) to the
EXT terminal connected to a device
which cannot output an S-VIDEO (Y/C
signal). If it is set wrongly, a picture
cannot appear.
1 Press the 5
55
5 or 6
66
6 buttons to
choose an EXT terminal
2 Press the yellow button and set the
S-IN (S-VIDEO input).
Then press the a
aa
a button
An S-IN (S-VIDEO input) mark is
displayed. You can view an S-VIDEO
signal (Y/C signal) instead of the regular
video signal (composite signal).
To cancel the S-IN (S-VIDEO input)
setting:
Press the yellow button and turn off S-IN (S-
VIDEO input) mark. The regular video
signal (composite signal) pictures are
resumed.
The EXT-1 terminal does not support S-
VIDEO signal (Y/C signal) and you
cannot set S-IN (S-VIDEO input) in the
EXT-1 terminal.
Setting S-IN (S-VIDEO input) changes
the head character from “E” to “S”. For
example, “E2” is changed to “S2”.
Even a device which enables the S-
VIDEO signal (Y/C signal) to be output
may output a regular video signal
(composite signal) depending on the
device setting. If a picture cannot appear
because S-IN (S-VIDEO input) setting
has been made, read the device Instruction
Manual carefully again to check for the
device settings.
ID LIST
You can have a name corresponding to the
devices connected for each EXT terminal.
Giving a name to an EXT terminal makes the
EXT terminal number appear on the screen,
together with the name.
1 Press the 5
55
5 or 6
66
6 buttons to
choose an EXT terminal
2 Press the blue button to display the
name list (ID LIST)
D0110-EN
S-IN
ID LIST
OK
EXT-1
EXT-3
DUBBING
EXT-2
EXT-4
EXT-5
TV
> EXT SETTING
D0021-EN
ID LIST
VHS
S-VHS
DVC
CAM
SAT
STB
GAME
DVD
DVR
EXT-1
EXT-3
DUBBING
EXT-2
EXT-4
EXT-5
TV
> EXT SETTING
OK
HV-36P38SUE_Eng.book Page 38 Friday, September 26, 2003 11:10 AM
SET UP menu
39
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
3 Press the 6
66
6 buttons to choose a
name. Then press the a
aa
a button
The ID LIST disappears and the name is
assigned to the EXT terminal.
You cannot assign an EXT terminal
name not found in the name list (ID
LIST).
To erase a name assigned to the
EXT terminal:
Choose a blank space.
4 Press the a
aa
a button to complete
the setting
DUBBING
You can choose a signal source to be output
from an EXT-2 terminal.
You can choose any one of the output signal
of the device connected to the EXT terminal
and the picture and sound from a TV channel
you are currently viewing to output it to the
EXT-2 terminal.
1 Press the 5
55
5 buttons to choose
the arrow from the menu
2 Press the 6
66
6 buttons to choose an
EXT terminal or TV.
Then press the a
aa
a button
The arrow in the menu represents a signal
flow. The left side of the arrow denotes a
signal source output from the EXT-2
terminal.
EXT-1/EXT-3/EXT-5:
The output signal of the device connected
to an EXT terminal passes through the TV
and is output from the EXT-2 terminal.
TV:
The picture and sound of the TV channel
you are currently viewing are output from
the EXT-2 terminal.
During dubbing, you cannot turn off
the TV. Turning off the TV also turns
off the output from the EXT-2
terminal.
When you choose an EXT terminal as
an output, you can view a TV
programme or a picture from the other
EXT terminal while dubbing the
picture from a device connected to the
EXT terminal onto a VCR connected
to the EXT-2 terminal.
The RGB signals from the TV games
cannot be output. Teletext programmes
cannot be output.
D0022-EN
OK
EXT-1
EXT-3
DUBBING
EXT-2
EXT-4
EXT-5
TV
> EXT SETTING
HV-36P38SUE_Eng.book Page 39 Friday, September 26, 2003 11:10 AM
40
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Additional preparation
Connecting the external devices
Connect the devices to the TV, paying
attention to the following connection
diagram.
Before connecting anything:
Read the manuals provided with the
devices. Depending on the devices, the
connection method may differ from the
figure. In addition, the device settings
may be changed depending on the
connection method to secure proper
operation.
Turn off all the devices including the TV.
The “Specifications” on page 48 contains
the details of the EXT terminals. If you
are connecting a device not listed in the
following connection diagram, see the
table to choose the best EXT terminal.
Note that connecting cables are not
supplied.
1 VCR (composite signal)
2 VCR (composite signal/S-VIDEO signal)
3 T-V LINK compatible VCR (composite
signal/S-VIDEO signal)
4 Decoder
5 DVD player (composite signal/S-VIDEO
signal)
6 DVD player (composite signal/RGB
signal)
7 DVD player (component video signals;
Pr/Pb/Y)
8 TV game (composite signal/RGB signal)
9 TV game (composite signal/S-VIDEO
signal)
0 Headphones
- Camcorder (composite signal/S-VIDEO
signal)
= SCART cable
~ Audio cable
! Video cable
@ S-VIDEO cable
# Component cable
EXT-1
EXT-
4
EXT-2
S
EXT-3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
R
P
L
S
EXT-5
R
P
L
S
EXT-5
Back of the TV
Front of the TV
HV-36P38SUE
HV-36P38SUE_Eng.book Page 40 Friday, September 26, 2003 11:10 AM
Additional preparation
41
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
EXT-1
EXT-
4
EXT-2
S
EXT-3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
R
L
S
P
E
X
T
5
EXT-
1
EXT-
4
EXT-
2
S
EXT-
3
S
AUDIO OUT
L
Pr
Pb
R
L
Y
R
R
L
S
P
E
X
T
5
Back of the TV
Back of the TV
HV-32P37SUE/HV-28P37SUE
HV-36P38SUE_Eng.book Page 41 Friday, September 26, 2003 11:10 AM
42
Additional preparation
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Devices which can output the S-
VIDEO signal (Y/C signal) such as
a S-VHS VCR
Connect the device to an EXT terminal other
than the EXT-1 terminal.
You can choose a video input signal from the
S-VIDEO signal (Y/C signal) and regular
video signal (composite signal). For details
of how to operate the device, see “S-IN (S-
VIDEO input)” on page 37.
T-V LINK compatible VCR
Be sure to connect the T-V LINK compatible
VCR to the EXT-2 terminal. If not, the T-V
LINK function will not work properly.
When connecting a T-V LINK compatible
VCR to the EXT-2 terminal, be sure to
connect the Decoder to the VCR. If not,
the T-V LINK function may not work
properly. After you have registered TV
channels to the Programme numbers (PR),
set the DECODER (EXT-2) function for
the Programme number (PR) to ON in
order to unscramble a scrambled TV
channel. For details of operation, see
“DECODER (EXT-2)” on page 36.
Connecting headphones
Connect the headphones with a stereo mini-
jack (of 3.5 mm in diameter) to the
headphone jack at the TV rear panel.
No sound comes out from the TV
speakers when the headphones are
connected and only one screen is
displayed.
Video/sound signal output from
the EXT-2 terminal
You can arbitrarily change over the output of
the video/sound signal from the EXT-2
terminal. It is useful when you want to dub
the video/sound from another device on the
VCR connected to the EXT-2 terminal. For
details on how to do this operation, see
“DUBBING” on page 39.
TV output from the EXT-1 terminal
The output of video/sound signal of a TV
channel you are currently viewing is always
output from the EXT-1 terminal.
Changing over a Programme number (PR)
also changes over the TV output from the
EXT-1 terminal.
The video/sound signal from an EXT
terminal cannot be output.
Teletext programmes cannot be output.
Connecting Speakers/Amplifier
While referring to the Audio equipment
connection diagram, connect the audio
equipment you desire to the TV.
You can use external front speakers to listen
to the TV sound instead of the TV speakers.
Before connecting anything:
Read the manuals provided with the
amplifier and speakers.
Turn the TV and Amplifier off.
To prevent magnetism from the speakers
adversely effecting the TV screen, use
magnetic-shielded speakers for the front
speakers.
Note that connecting cables are not
supplied.
The output from the AUDIO OUT
terminal is not interrupted by headphone
connection to the TV. You cannot cut the
sound from the front speaker even if you
connect a headphone to the TV.
Adjust the volume of the external
speakers with the amplifier.
L
R
Back of the TV
1 Amplifier
2 Front speakers (Magnetic-shielded type)
HV-36P38SUE_Eng.book Page 42 Friday, September 26, 2003 11:10 AM
44
CH/CC numbers
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
When two CH/CC numbers correspond to one Channel number, choose either one according to
the current COUNTRY setting. When the COUNTRY setting is other than FRANCE, choose a
two-digit CH/CC number. When the COUNTRY setting is FRANCE, choose a three-digit CH/
CC number.
Find the CH/CC number (CC110 to CC161) corresponding to the TV channel (SECAM-L
system) from a French cable TV station, based on the broadcast frequency of the TV channel.
When you do not know the broadcast frequency, please contact the cable TV station.
The CH/CC numbers of CH102-CH169 and CC110-CC161 correspond to the TV channels
being broadcast by a SECAM-L system. The other CH/CC numbers correspond to the TV
channels being broadcast by a method other than a SECAM-L system.
HV-36P38SUE_Eng.book Page 44 Friday, September 26, 2003 11:10 AM
45
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Troubleshooting
If a problem arises while you are using the TV, please read this “Troubleshooting” well before
you request having the TV repaired. You may be able to fix it easily by yourself. For example, if
the AC plug is disconnected from the AC outlet, or the TV aerial has problems, you may think
there is a problem with the TV itself.
Important:
This Troubleshooting guide only covers problems whose cause are not easy to determine. If a
question arise when you are operating a function, read the page(s) corresponding to the
operation of the function well, not this Troubleshooting guide.
After you have followed the Troubleshooting description or the operating description of the
functions concerned without any success, remove the AC plug from the AC outlet and request
a repair of your TV. Do not attempt to repair the TV by yourself or remove the rear cover of
the TV.
If you cannot turn on the TV
Is the AC plug connected to the AC
outlet?
Is the Power lamp lit? If not, press the
Main power button.
Make sure to set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV on when the VCR/TV/DVD
switch is set to the VCR or DVD position.
If you cannot turn off the TV
Make sure to set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV off when the VCR/TV/DVD
switch is set to the VCR or DVD position.
No picture/No sound
Have you chosen a TV channel whose
reception is extremely bad? In this case,
the BLUE BACK function will be
activated, the entire screen becomes blue,
and the sound is muted. In spite of this, if
you want to view the TV channel, follow
the description “BLUE BACK” on
page 31 to try to change the BLUE BACK
function setting to OFF.
If the SYSTEM setting for a TV channel
is incorrect, it may prevent the sound
from being issued. Follow the description
“EDIT/MANUAL” on page 32 to use the
MANUAL function to try to change the
SYSTEM setting.
Poor picture
If noise totally obscures the picture
(snow), the aerial or aerial cable may have
trouble. Check the following to try to
solve the trouble:
Has the TV and aerial been connected
properly?
Has the aerial cable been damaged?
Is the aerial pointed to the right
direction?
Is the aerial itself faulty?
If the TV or aerial receives interference
from the other devices, stripes or noise
may appear in the picture. Move such
devices as an amplifier, personal
computer, or a hair drier that can cause
interference away from your TV, or try
changing its location. If the aerial suffers
interference from a radio tower or high-
voltage wire, please contact your local
dealer.
If the TV receives interference from
signal reflecting from mountains or
building, double-pictures (ghosting) will
occur. Try to change the aerial’s direction
or replace the antenna with the one with
better directionality.
Are your COLOUR SYSTEM settings for
the TV channels correct? Follow the
description “COLOUR SYSTEM” on
page 26 to try to solve the trouble.
HV-36P38SUE_Eng.book Page 45 Friday, September 26, 2003 11:10 AM
Troubleshooting
47
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
It takes a short period of time from the
time an operation such as changing
channels is performed until an image is
displayed. This is not a malfunction. This
is the time required for the image to
stabilize before it can be displayed.
The TV may emit a crackling sound due
to a sudden change in temperature. It does
not matter if a picture or sound does not
show any abnormality. If you hear
crackling sounds frequently while you are
viewing the TV, other causes may be
assumed. For precautionary purposes,
request your service technician to inspect
it.
Touching the screen may cause you feel a
slight electric shock due to its static
electricity. It is an unavoidable
phenomenon due to the construction of
the picture tube. It is not a problem with
the TV. You can rest assured that this
static discharge does not have harmful
influence over the human body.
When set to 2-pictures multi, adjust the
headphone sound with HEADPHONE
VOLUME in the SOUND menu.
HV-36P38SUE_Eng.book Page 47 Friday, September 26, 2003 11:10 AM
Specifications
49
ENGLISH
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English
Design and specifications subject to change without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of the
owners of copyright of the original picture sources, as this constitutes an infringement of copyright.
Model
Item
HV-32P37SUE HV-28P37SUE
Broadcasting systems CCIR B/G, I, D/K, L
Colour systems PAL, SECAM
The EXT terminals also support the NTSC 3.58/4.43 MHz system.
Channels and frequencies E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY
H+2, F2-F10, F21-F69, R1-R12, R21-R69
French cable TV channel of broadcast frequencies 116 - 172 MHz and 220 -
469 MHz
Sound-multiplex systems A2 (B/G, D/K), NICAM (B/G, I, D/K, L) system
Teletext systems FLOF (Fastext), TOP, WST (World Standard System)
Power requirements 220 - 240 V AC, 50 Hz
Power consumption 137 W, Standby: 2.0 W 127 W, Standby: 2.0 W
Picture tube size Viewable area 76 cm
(measured diagonally)
Viewable area 66 cm
(measured diagonally)
Audio output Rated Power output: 10 W + 10 W
Speakers (13 cm × 6.5 cm) oval × 2
EXT-1 terminal Euroconnector (21-pin, SCART)
Video input, Audio L/R inputs and RGB inputs are available.
TV broadcast outputs (Video and Audio L/R) are available.
EXT-2 terminal Euroconnector (21-pin, SCART)
Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are
available.
Video and Audio L/R outputs are available.
T-V LINK functions are available.
EXT-3 terminal Euroconnector (21-pin, SCART)
Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
EXT-4 terminal RCA connectors × 5
Component video (Pr, Pb, Y) inputs (625p, 525p, 1125i) and Audio L/R inputs
are available.
EXT-5 terminal RCA connectors × 3
S-VIDEO connector × 1
Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
AUDIO OUT terminal RCA connectors × 2
Audio L/R outputs are available.
Output level 0.5 Vrms.
Headphone jack Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D) 948 mm × 562 mm × 550 mm 854 mm × 508 mm × 493 mm
Weight 54.0 kg 38.0 kg
Accessories Remote control unit × 1 (RM-C1800)
AA/R6 dry cell battery × 2
HV-36P38SUE_Eng.book Page 49 Friday, September 26, 2003 11:10 AM
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / All Cover
Cover04
LCT1537-001A-U
0903-T-CR-JMUK
LCT1537-001A-U_Cover.fm Page 6 Thursday, September 25, 2003 10:00 AM
47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC HV28P37SUE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von JVC HV28P37SUE

JVC HV28P37SUE Bedienungsanleitung - Deutsch - 52 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info