Bedienungsanleitung JVC kd-g402 (Seite 17 von 155) (Deutsch, Englisch, Holländisch, Französisch)

163273

Zoom out

Zoom in

Vorherige Seite

1/155

Nächste Seite

ENGLISH

Setting the TA volume level

You can preset the volume level for TA Standby

Reception. When a traffic programme is received,

the volume level automatically changes to the

preset level.

• See also “Changing the general settings

(PSM)” on page 30.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2 Press ¢ or 4 to select “TA VO L”

(volume).

3 Turn the control dial to set to the desired

volume.

You can set it from “VOL 00” to “VOL 30” or

“VOL 50” (depending on the amplifier gain

control setting: see page 32).

4 Press SEL (select) to finish the setting.

Automatic clock adjustment

When shipped from the factory, the clock built in

this unit is set to be readjusted automatically

using the CT (Clock Time) data in the RDS

signal.

If you do not want to use automatic clock

adjustment, follow the procedure below.

• See also “Changing the general settings

(PSM)” on page 30.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2 Press ¢ or 4 to select “AUTO

ADJ” (adjustment).

3 Turn the control dial counterclockwise to select

“OFF.”

Now automatic clock adjustment is canceled.

4 Press SEL (select) to finish the setting.

To reactivate clock adjustment, repeat the

same procedure and select “ON” in step 3 by

turning the control dial clockwise.

Note:

You must stay tuned to the same station for more than

2 minutes after setting “AUTO ADJ” to “ON.”

Otherwise, the clock time will not be adjusted. (This is

because the unit takes up to 2 minutes to capture the

CT data in the RDS signal.)

Other convenient RDS

functions and adjustments

Automatic selection of the station

when using the number buttons

Usually when you press the number button, the

preset station is tuned in.

However, when the preset station is an RDS

station, something different will happen. If the

signals from that preset station are not sufficient

for good reception, this unit, using the AF data,

tunes in to another frequency broadcasting the

same programme as the original preset station is

broadcasting. (Programme search)

• The unit takes some time to tune in to another

station using programme search.

To activate programme search, follow the

procedure below.

• See also “Changing the general settings

(PSM)” on page 30.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2 Press ¢ or 4 to select

“P(Programme)-SEARCH.”

3 Turn the control dial clockwise to select “ON.”

Now programme search is activated.

4 Press SEL (select) to finish the setting.

To cancel programme search, repeat the same

procedure and select “OFF” in step 3 by turning

the control dial counterclockwise.

EN12-18_KD-G401[E_EX_EU]f.p65 7/11/03, 7:12 PM17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC kd-g402 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info