Bedienungsanleitung JVC KD-T822BT (Seite 27 von 140) (Englisch, Holländisch, Portugiesisch, Spanisch)

804006

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

ENGLISH 19

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Audio Settings

[SUB.W LEVEL]*1 [SPK-OUT]*2 (Not applicable when 3-way crossover is selected.)

[SUB.W00] to [SUB.W+06] ([SUB.W+03]): Adjusts

the output level of the subwoofer connected via speaker

lead. (Page 31)

[PRE-OUT]*3 [SUB.W–50] to [SUB.W+10] ([SUB.W00]): Adjusts

the output level of the subwoofer connected to the

lineout terminals (REAR/SW) through an external

amplifier. (Page 31)

[SUBWOOFER

SET]*3

[ON]: Turns on the subwoofer output. ; [OFF]: Cancels.

[FADER] (Not applicable when 3-way crossover is selected.)

[POSITIONR15] to [POSITIONF15] ([POSITION00]): Adjusts the front

and rear speaker output balance.

[BALANCE]*4 [POSITIONL15] to [POSITIONR15] ([POSITION00]): Adjusts the left and

right speaker output balance.

[VOLUME

ADJUST]

[LEVEL–15] to [LEVEL+06] ([LEVEL00]): Presets the initial volume level

of each source by comparing to the FM volume levels.

(Before adjustment, select the source you want to adjust.)

[AMPGAIN] [LOWPOWER]: Limits the maximum volume level to 25. (Select if the

maximum power of each speaker is less than 50 W to prevent damaging

the speakers.) ; [HIGHPOWER]: The maximum volume level is 35.

[SPK/PREOUT] (Not applicable when 3-way crossover is selected.)

Depending on the speaker connection method, select the appropriate

setting for the desired output. (See “Speaker output settings” on

page 20.)

[SPEAKER SIZE] Depending on the crossover type you have selected (see the following

[X'OVER TYPE]), 2-way crossover or 3-way crossover setting items will be

shown. (See “Crossover settings” on page 21.)

By default, 2-way crossover type is selected.

[X ' OVER]

[DTA SETTINGS] For settings, see “Digital Time Alignment settings” on page 23.

[CAR SETTINGS]

[X ‘ OVER TYPE] Caution: Adjusts the volume before changing the [X ‘ OVER TYPE] to avoid

the sudden increase or decrease of the output level.

• Once you have changed the crossover type, the next time when you turn

on the power, the display shows:

“2-WAY X’OVER” or “3-WAY X’OVER” “PRESS” “VOLUME KNOB”

“TO CONFIRM”

Press the volume knob to acknowledge in order to proceed to the next

desired operation.

[2-WAY] (Displayed only when [3-WAY] is selected.)

[YES]: Selects two way crossover type. ; [NO]: Cancels.

[3-WAY] (Displayed only when [2-WAY] is selected.)

[YES]: Selects three way crossover type. ; [NO]: Cancels.

*1 Displayed only when [SUBWOOFER SET] is set to [ON].

*2 For 2-way crossover: Displayed only when [SPK/PREOUT] is set to [SUB.W/SUB.W].

(Page 20)

*3 For 2-way crossover: Displayed only when [SPK/PREOUT] is set to [REAR/SUB.W] or

[SUB.W/SUB.W]. (Page 20)

*4 This adjustment will not affect the subwoofer output.

KD_T822BT_E_B5A-3833-00_EN_4th Draft.indd 19KD_T822BT_E_B5A-3833-00_EN_4th Draft.indd 19 6/7/2021 12:00:51 AM6/7/2021 12:00:51 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC KD-T822BT Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC KD-T822BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info