Bedienungsanleitung JVC KW-DB92BTE (Seite 32 von 96) (Deutsch, Englisch, Französisch)

663479

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

INSTALLATION / CONNECTION

Warning

• The unit can only be used with a 12V DC power supply, negative ground.

• Disconnect the battery’s negative terminal before wiring and mounting.

• Do not connect Battery wire (yellow) and Ignition wire (red) to the car

chassis or Ground wire (black) to prevent a short circuit.

• Insulate unconnected wires with vinyl tape to prevent a short circuit.

• Be sure to ground this unit to the car’s chassis again after installation.

Caution

• For safety’s sake, leave wiring and mounting to professionals. Consult the

car audio dealer.

• Install this unit in the console of your vehicle. Do not touch the metal parts

of this unit during and shortly after use of the unit. Metal parts such as the

heat sink and enclosure become hot.

• Do not connect the

wires of speakers to the car chassis or Ground wire

(black), or connect them in parallel.

• Connect speakers with a maximum power of more than 50W. If the

maximum power of the speakers is lower than 50W, change the

[AMP GAIN]

setting to avoid damaging the speakers.

(



18)

• Mount the unit at an angle of less than 30º.

• If your vehicle wiring harness does not have the ignition terminal, connect

Ignition wire (red) to the terminal on the vehicle’s fuse box which provides

12 V DC power supply and is turned on and off by the ignition key.

• Keep all cables away from heat dissipate metal parts.

• After the unit is installed, check whether the brake lamps, blinkers, wipers,

etc. on the car are working properly.

• If the fuse blows, first make sure the wires are not touching car’s chassis,

then replace the old fuse with one that has the same rating.

Basic procedure

Remove the key from the ignition switch, then

disconnect the

terminal of the car battery.

2 Connect the wires properly.

See Wiring connection.

(



30)

3 Install the unit to your car.

See Installing the unit (in-dash mounting).

4 Connect the terminal of the car battery.

5 Press to turn on the power.

6 Reset the unit within 5 seconds.

(



Do the required wiring.

(



)

Dashboard of your car

Bend the appropriate tabs to hold

the mounting sleeve firmly in place.

Installing the unit (in-dash mounting)

When installing without the

mounting sleeve

1 Remove the mounting sleeve and

trim plate from the unit.

2 Align the holes in the unit (on

both sides) with the vehicle

mounting bracket and secure the

unit with screws (supplied).

How to remove the unit

Fit the catch pin on the

extraction keys into the holes on

both sides of the trim plate, then

pull it out.

2 Insert the extraction keys deeply

into the slots on each side, then

follow the arrows as shown

below.

Use only the specified screws. Using wrong

screws might damage the unit.

JS_JVC_KW_R920BT_DB92BT_E_EN_1.indd 28JS_JVC_KW_R920BT_DB92BT_E_EN_1.indd 28 3/11/2015 9:00:07 AM3/11/2015 9:00:07 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC KW-DB92BTE Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC KW-DB92BTE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info