Bedienungsanleitung JVC KW-M27DBT (Seite 23 von 36) (Englisch)

803999

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

English |

InstallationInstallation

Before Installation

Before installation of this unit, please note the

following precautions.

#WARNINGS

• If you connect the ignition wire (red) and the battery

wire (yellow) to the car chassis (ground), you may

cause a short circuit, that in turn may start a ﬁre.

Always connect those wires to the power source

running through the fuse box.

• Do not cut out the fuse from the ignition wire (red)

and the battery wire (yellow). The power supply

must be connected to the wires via the fuse.

#CAUTION

• Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during and

shortly after the use of the unit. Metal part such as

the heat sink and enclosure become hot.

✎NOTE

• Mounting and wiring this product requires skills and

experience. For best safety, leave the mounting and

wiring work to professionals.

• Make sure to ground the unit to a negative 12V DC

power supply.

• Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of water

splashing.

• Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

• If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that

can be turned on and oﬀ with the ignition key. If you

connect the ignition wire to a power source with a

constant voltage supply, such as with battery wires,

the battery may be drained.

• If the console has a lid, make sure to install the unit

so that the front panel will not hit the lid when

closing and opening.

• If the fuse blows, ﬁrst make sure the wires aren’t

touching to cause a short circuit, then replace the

old fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not

remove the caps on the ends of the unconnected

wires or the terminals.

• Secure the wires with cable clamps and wrap vinyl

tape around the wires that comes into contact with

metal parts to protect the wires and to prevent short

circuit.

• Connect the speaker wires correctly to the terminals

to which they correspond. The unit may be

damaged or fail to work if you share the ¤ wires or

ground them to any metal part in the car.

• When only two speakers are being connected to

the system, connect the connectors either to both

the front output terminals or to both the rear output

terminals (do not mix front and rear). For example,

if you connect the ¢ connector of the left speaker

to a front output terminal, do not connect the ¤

connector to a rear output terminal.

• After the unit is installed, check whether the brake

lamps, blinkers, wipers, etc. on the car are working

properly.

• Mount the unit so that the mounting angle is 30°

or less.

• Do not press hard on the panel surface when installing

the unit to the vehicle. Otherwise scars, damage, or

failure may result.

• Reception may drop if there are metal objects near

the Bluetooth antenna.

Bluetooth antenna unit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC KW-M27DBT Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC KW-M27DBT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info