Bedienungsanleitung JVC KW-M560BT (Seite 22 von 112) (Deutsch, Englisch, Holländisch, Französisch)

732201

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Connection/Installation

Before Installation

Before installation of this unit, please note the

following precautions.

# WARNINGS

• If you connect the ignition wire (red) and

the battery wire (yellow) to the car chassis

(ground), you may cause a short circuit, that

in turn may start a ﬁre. Always connect those

wires to the power source running through

the fuse box.

• Do not cut out the fuse from the ignition wire

(red) and the battery wire (yellow). The power

supply must be connected to the wires via

the fuse.

# CAUTION

• Install this unit in the console of your vehicle.

Do not touch the metal part of this unit during

and shortly after the use of the unit. Metal part

such as the heat sink and enclosure become

hot.

NOTE

• Mounting and wiring this product requires

skills and experience. For best safety, leave the

mounting and wiring work to professionals.

• Make sure to ground the unit to a negative 12V

DC power supply.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• If the power is not turned ON (“There is an

error in the speaker wiring. Please check

the connections.” is displayed), the speaker

wire may have a short-circuit or touched

the chassis of the vehicle and the protection

function may have been activated. Therefore,

the speaker wire should be checked.

• If your car’s ignition does not have an ACC

position, connect the ignition wires to a power

source that can be turned on and oﬀ with the

ignition key. If you connect the ignition wire

to a power source with a constant voltage

supply, such as with battery wires, the battery

may be drained.

• If the console has a lid, make sure to install the

unit so that the front panel will not hit the lid

when closing and opening.

• If the fuse blows, ﬁrst make sure the wires

aren’t touching to cause a short circuit, then

replace the old fuse with one with the same

rating.

• Insulate unconnected wires with vinyl tape

or other similar material. To prevent a short

circuit, do not remove the caps on the ends of

the unconnected wires or the terminals.

• Connect the speaker wires correctly to the

terminals to which they correspond. The unit

may be damaged or fail to work if you share

the ¤ wires or ground them to any metal part

in the car.

• When only two speakers are being connected

to the system, connect the connectors either

to both the front output terminals or to both

the rear output terminals (do not mix front

and rear). For example, if you connect the ¢

connector of the left speaker to a front output

terminal, do not connect the ¤ connector to

a rear output terminal.

• After the unit is installed, check whether the

brake lamps, blinkers, wipers, etc. on the car

are working properly.

• Do not press hard on the panel surface when

installing the unit to the vehicle. Otherwise

scars, damage, or failure may result.

• Reception may drop if there are metal objects

near the Bluetooth antenna.

Bluetooth antenna unit

!B5H-0357-04_QSG_JVC_KWM_E_EnFrDeNl.indb 22 2020/02/17 18:05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC KW-M560BT Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC KW-M560BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info