Bedienungsanleitung JVC KW-V235DBT (Seite 63 von 80) (Englisch)

663442

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH 63

CONNECTION/INSTALLATIONCONNECTION/INSTALLATION

Before installing the unit

V WARNING

• If you connect the ignition wire (red) and the

battery wire (yellow) to the car chassis (ground),

you may cause a short circuit, that in turn may

start a fire. Always connect those wires to the

power source running through the fuse box.

• Do not cut out the fuse from the ignition wire (red)

and the battery wire (yellow). The power supply

must be connected to the wires via the fuse.

V Precautions on installation and connection

• Mounting and wiring this product requires

skills and experience. For best safety, leave the

mounting and wiring work to professionals.

• Make sure to ground the unit to a negative 12V

DC power supply.

• Do not install the unit in a location exposed to

direct sunlight or excessive heat or humidity. Also

avoid places with too much dust or the possibility

of water splashing.

• Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

• If the power is not turned on (“Miswiring DC Offset

Error”, “Warning DC Offset Error” is displayed),

the speaker wire may have a short circuit or

have touched the chassis of the vehicle and the

protection function may have been activated.

Therefore, the speaker wire should be checked.

• Keep all cables away from heat dissipating metal

parts.

• If your car’s ignition does not have an ACC

position, connect the ignition wires to a power

source that can be turned on and off with the

ignition key. If you connect the ignition wire to a

power source with a constant voltage supply, such

as with battery wires, the battery may be drained.

• If the fuse blows, first make sure the wires are not

touching to cause a short circuit, then replace the

old fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or

other similar material. To prevent a short circuit,

do not remove the caps on the ends of the

unconnected wires or the terminals.

• Connect the speaker wires correctly to the

terminals to which they correspond. The unit may

be damaged or fail to work if you share the ·

wires or ground them to any metal part in the car.

• When only two speakers are being connected to

the system, connect both connectors either to

the front output terminals or to the rear output

terminals (do not mix front and rear). For example,

if you connect the ª connector of the left speaker

to a front output terminal, do not connect the ·

connector to a rear output terminal.

• After the unit is installed, check whether the brake

lamps, blinkers, wipers, etc. on the car are working

properly.

• Mount the unit so that the mounting angle is 30°

or less.

• Do not press hard on the panel surface when

installing the unit to the vehicle. Otherwise

scratches, damage, or failure may result.

V CAUTION

Install this unit in the console of your vehicle.

Do not touch the metal parts of this unit during

and shortly after the use of the unit. Metal parts

such as the heat sink and enclosure become hot.

❏ Supplied accessories for installation

1 Wiring harness x 1

2 Trim plate x 1

3 Extension wire (2 m) x 1

4 Extraction keys x 2

5 Microphone (3 m) x 1

❏ Installation procedure

1 To prevent a short circuit, remove the key

from the ignition and disconnect the

battery.

2 Make the proper input and output wire

connections for each unit.

3 Connect the speaker wires of the wiring

harness.

4 Take Connector B on the wiring harness

and connect it to the speaker connector in

your vehicle.

5 Take Connector A on the wiring harness

and connect it to the external power

connector in your vehicle.

6 Connect the wiring harness connector to

the unit.

7 Install the unit in your car.

• Make sure that the unit is installed securely

in place. If the unit is unstable, it may

malfunction (eg, the sound may skip).

8 Reconnect the · battery.

9 Press the reset button. (Page3)

10 Configure <Initial Settings>. (Page4)

2017_KW-V_Entry_E.indb 632017_KW-V_Entry_E.indb 63 2016/09/27 17:412016/09/27 17:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC KW-V235DBT Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC KW-V235DBT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info