Bedienungsanleitung JVC LT-20A60 SU (Seite 22 von 33) (Englisch)

537208

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

ENGLISH - 21 -

In stereo transmission it yields a phase differ-

ence between left and right channels. Hyper

Sound selection will be displayed on the

screen when the TV Status button is pressed

or programme is changed.

Picture Mode

Picture mode OSD is displayed when BLUE

button is pressed. Picture mode can be

changed to standard, soft, and bright.

Sleep Timer

Sleep Timer mode OSD is displayed when

YELLOW button is pressed.

The Sleep Timer is used to turn the TV off after

a defined period of time after selecting this

item. The timer can be programmed between

Off and 120 minutes in steps of 10 minutes.

(OFF, 010, 020, 030, 040, ... , 120)

If sleep timer is activated, at the end of the

selected the time, the TV goes automatically

to stand-by mode.

Mute Indicator

It is placed in the upper middle of the screen

when enabled, and it stays there until it is dis-

abled.

To cancel mute, there are two alternatives; the

first one is by pressing the "

" button, this

volume is set to the preceding value, and the

second one is increasing the volume level. By

decreasing the volume level in mute state,

mute will not be ignored, only the volume level

will decrease.

No-Signal Detection (TV mode)

If no valid signal detected, it takes 5 minutes

to switch to the Stand-By mode unless any

signal detected or any Remote Control com-

mand is accessed.

After a Remote Control command (if No-Sig-

nal Timer is active) the timer stops and if no

signal detected again the timer is initialized to

5 minutes and starts 3 seconds later again to

count down.

It is not valid in EXT modes.

No-Signal and Out Of Range

Detection (PC mode)

In PC Mode,as no menu is displayed,in case

that there is no PC input to the TV,it is dis-

played an OSD message:

No input signal detected

then the power lamp turns to amber and PC

will be in PC standby mode. Press AV button,

digit buttons or   /   buttons to exit

standby mode.

In PC Mode,as no menu is displayed,in case

that there is no PC input to the TV, but the reso-

lution and the vertical frequency is not sup-

ported by the concept, it is displayed an OSD

message:

Signal out of range

Volume Bar

It is displayed in the lower middle of the screen.

When a volume command is received (press-

ing 

+ or  - by Remote Control or

Control panel at the top of the TV) and no menu

is active, it stays on the screen for 3 seconds,

after the last volume command or until an-

other command is received in between.

EXT Modes

By pressing the AV button you can switch

your TV to EXT modes (except being in Tele-

text). Pressing this button will consecutively

switch the TV in one of the optional EXT

modes: EXT-1, EXT-2, EXT-2 S, EXT-3,

EXT-4, EXT-4 S and PC.

LT_20A60_SU.p65 31.08.2005, 08:1721

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC LT-20A60 SU Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC LT-20A60 SU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info