Bedienungsanleitung JVC LT-26DA20 (Seite 20 von 32) (Englisch)

512784

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English - 19 -

for the channels. For each valid channel number, signal

level and signal quality are shown on the screen.

In both manual and auto search any existing channel

in the database is not re-stored to avoid redundant

duplicates of that channel.

Clear Service List (*)

(*) This setting is visible only when the Country option

is set to Denmark, Sweden, Norway or Finland.

Use this setting to clear channels stored. Press “

” or “ ”

button to select Clear Service List and then press OK. The

following OSD message will be displayed on the screen:

Press OK to cancel. Select Yes by pressing “ ” or “ ”

button and press OK to delete all of the channels.

First Time Installation

The user can use this item to load default settings,

which were loaded to the receiver at the factory.

To install factory settings, highlight “First Time

Installation” menu item and press “OK” button,

then you will be asked whether or not to delete the

settings. Selecting “Yes” by pressing “OK” button

while the “Yes” is highlighted will delete the existing

channel table.

Then you will be asked to conﬁ rm for deleting all

channels and settings:

By selecting Yes and pressing the “OK” button, the

existing channel table will be deleted. After factory

settings are loaded, “First Time Installation” menu

will be displayed.

The menu which is displayed for language selection

appears on the screen at ﬁ rst. By using “

” or “ ”

buttons, select the desired language option, and press

OK button to activate.

After then, “First time installation” OSD will appear

on the screen. By pressing “

” or “ ” buttons, select

the Country you want to set and press “OK” button

(* only for EU countries).

Press the “OK” button to start installation. After search

is completed for digital channels, a message asking

whether to search for analogue channels appears

on the screen.This process is same as described in

Automatic Search section..

Analogue TV Menu System

Picture Menu

Mode

For your viewing requirements, you can set the related

mode option.

Press “

” or “ ” button to select Mode. Press “

” or “ ” button to choose from one of these options:

Cinema, Dynamic and Natural.

Brightness/Contrast/Colour/Sharpness/

Hue

Press “ ” or “ ” button to select the desired option.

Press “ ” or “ ” button to set the level.

Note: Hue option can only be visible when the TV receives

an NTSC signal.

Colour Temp

Press “ ” or “ ” button to select Colour Temp. Press

“ ” or “ ” to choose from one of these options: Cool,

Normal and Warm.

Note:

• Setting Cool option gives white colours a slight blue

stress.

• Setting Warm option gives white colours a slight red

stress.

• For normal colours, select Normal option.

Noise Reduction

If the broadcast signal is weak and the picture is

noisy, use Noise Reduction setting to reduce the

noise amount.

Press “

” or “ ” button to select Noise Reduction.

Press “ ” or “ ” to choose from one of these options:

Low, Medium, High or Off.

A01_[GB]_MB45M_26741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067199_50162791.indd 19A01_[GB]_MB45M_26741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067199_50162791.indd 19 08.04.2010 08:47:4408.04.2010 08:47:44

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC LT-26DA20 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info