Bedienungsanleitung JVC RX-5060 (Seite 14 von 71) (Englisch, Französisch)

57258

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

English

When playing software encoded with Dolby Digital or DTS, the

following symptoms may occur:

• Sound does not come out at the beginning of playback.

• Noise comes out while searching for or skipping chapters or

tracks.

In this case, press INPUT DIGITAL repeatedly to select

“DOLBY DIGITAL” or “DTS SURROUND.”

• Each time you press INPUT DIGITAL, the input mode changes as

follows:

•When using the remote control, press ANALOG/DIGITAL

repeatedly to select “DOLBY DIGITAL” or “DTS SURROUND.”

Each time you press ANALOG/DIGITAL on the remote control,

the input mode changes as follows:

DIGITAL AUTO=DOLBY DIGITAL=DTS SURROUND

=ANALOG=(back to the beginning)

When “DOLBY DIGITAL” or “DTS SURROUND” is selected,

the DIGITAL AUTO indicator goes off, and the corresponding

digital signal format indicator lights up on the display.

• If the incoming signal does not match the selected digital signal

format, the indicator of the selected signal format will flash.

Note:

When you turn off the power or select another source, “DOLBY

DIGITAL” and “DTS SURROUND” settings are canceled and the digital

input mode is automatically reset to “DIGITAL AUTO.”

To select the analog input mode

Press INPUT ANALOG (or ANALOG/DIGITAL on the remote

control repeatedly until “ANALOG” appears on the display). The

ANALOG indicator lights up.

Changing the Display Brightness

You can dim the display.

Press DIMMER.

• Each time you press the button, the display dims and brightens

alternately.

Attenuating the Input Signal

When the input level of the analog source is too high, the sounds

will be distorted. If this happens, you need to attenuate the input

signal level to prevent the sound distortion.

• Once you have made adjustment, it is memorized for each analog

source.

Press and hold INPUT ATT (INPUT ANALOG) so that the

INPUT ATT indicator lights up on the display.

• Each time you press and hold the button, the input attenuator

mode turns on (“INPUT ATT ON”) and off (“INPUT

NORMAL”).

Changing the Source Name

When you have connected a CD recorder to the TAPE/CDR jacks on

the rear panel, change the source name which will be shown on the

display.

When changing the source name from “TAPE” to “CDR”:

1Press TAPE/CDR (SOURCE NAME).

• Make sure “TAPE” appears on the display.

2Press and hold SOURCE NAME (TAPE/CDR) until

“ASSIGN CDR” appears on the display.

To change the source name back to “TAPE,” repeat the same

procedure above.

Note:

Without changing the source name, you can still use the connected

components. However, there may be some inconvenience.

–“TAPE” will appear on the display when you select the CD recorder.

–You cannot use the digital input (see page 11) for the CD recorder.

DIGITAL AUTO DOLBY DIGITAL

DTS SURROUND

Remote

NOT

Remote

NOT

Basic Operations

09-13_RX-5060B[C].p65 05.12.24, 12:2012

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-5060 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC RX-5060

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info