Bedienungsanleitung JVC RX-5060 (Seite 35 von 71) (Englisch, Französisch)

57258

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

English

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s

service center.

SOLUTION

Plug the power cord into an AC outlet.

Check speaker wiring and reconnect if necessary.

(See page 5.)

Press SPEAKERS ON/OFF so that the sounds

come out of the speakers. (See page 11.)

Select the correct source.

Press MUTING to cancel the mute. (See page 13.)

Select the correct input mode (analog or digital).

(See pages 11 and 12.)

If subwoofer is connected, set “SUBWOOFER

YES” so that the SUBWOOFER OUT ON/OFF

button works.

Connect an outdoor FM antenna or contact your

dealer. (See page 4.)

Select a new station.

Check with your dealer to be sure you have the

correct antenna.

Check connections. (See pages 4 and 5.)

Move the antenna farther from automobile traffic.

1. Press STANDBY/ON

on the front panel to

turn off the receiver.

2. Stop the playback source.

3. Turn on the receiver again, and adjust the

volume.

Press STANDBY/ON

on the front panel to turn

off the receiver, then check the speaker wiring.

If “OVERLOAD” does not disappear, unplug the

AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your

dealer.

Press STANDBY/ON on the front panel to turn

off the receiver. After unplugging the AC power

cord, contact your dealer.

Press STANDBY/ON

on the front panel to turn

off the receiver. After unplugging the AC power

cord, contact your dealer.

Remove the obstruction.

Replace batteries. (See page 4.)

Select the correct remote control operation mode.

(See pages 29 to 32.)

POSSIBLE CAUSE

The power cord is not plugged in.

Speaker signal cables are not

connected.

The SPEAKERS ON/OFF button is

not set correctly.

An incorrect source is selected.

Muting is activated.

An incorrect input mode (analog or

digital) is selected.

The SUBWOOFER OUT ON/OFF

button is pressed while

“SUBWOOFER” is set to

“SUBWOOFER NO.”

Incoming signal is too weak.

The station is too far away.

An incorrect antenna is used.

Antennas are not connected properly.

Ignition noise from automobiles.

Speakers are overloaded because of

high volume.

Speakers are overloaded because of

short circuit of speaker terminals.

The built-in microcomputer is not

functioning correctly.

The receiver is overloaded because of

a high voltage.

There is an obstruction between the

remote sensor on the receiver and the

remote control.

Batteries are weak.

An incorrect remote control operation

mode is selected.

PROBLEM

The display does not light up.

No sound from speakers.

“NO SUBWOOFER” appears on the

display.

Continuous hiss or buzzing during FM

reception.

Noise is heard during FM/AM

reception.

“OVERLOAD” starts flashing on the

display.

“DSP NG” appears on the display.

The STANDBY lamp lights up after

turning on the power, and soon the

receiver turns off again (into standby

mode).

Remote control does not work.

Remote control does not work as you

intend.

28-34_RX-5060B[C].p65 05.12.24, 12:3333

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-5060 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC RX-5060

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info