Bedienungsanleitung JVC RX-5062 (Seite 24 von 71) (Englisch, Französisch)

57256

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

English

You can also use the remote control for

adjusting the speaker output level using

the test tone.

•You can also adjust the effect level

for DAP modes and Mono Film.

To adjust the speaker output level:

1Press SOUND.

The number buttons are activated

for sound adjustments.

2Press TEST to check if you can

hear the sounds through all the speakers at equal level.

Test tone (TEST TONE) comes out of the speakers in the

following order.

• No test tone comes out of the speakers for which the

speaker setting is set to “NONE” (or “SUBWOOFER NO”

for the subwoofer).

L (Left front)

C (Center)

R (Right front)

RS (Right surround)

LS (Left surround)

SW (Subwoofer)

(Back to the beginning)

3 Adjust the speaker output level (–10 dB to +10 dB).

•For the left front speaker: Press FRONT L, then LEVEL +/–.

•For the center speaker: Press CENTER, then LEVEL +/–.

•For the right front speaker: Press FRONT R, then

LEVEL +/–.

•For the right surround speaker: Press SURR R, then

LEVEL +/–.

•For the left surround speaker: Press SURR L, then

LEVEL +/–.

•For the subwoofer: Press SUBWFR, then LEVEL +/–.

Note:

When you press LEVEL +/– once, the current level for the

selected speaker appears on the display, and the test tone

comes out of the selected speaker.

If no adjustment is done for about 4 seconds, the adjustment

mode for the selected speaker is canceled.

4Press TEST again to stop the test tone.

To adjust the effect level:

1Press SOUND.

The number buttons are activated for sound adjustments.

2Press EFFECT repeatedly to select the effect level

(EFFECT 1 to EFFECT 5).

The source indication resumes about 4 seconds after the

adjustment.

Adjusting the Equalization Patterns

You can adjust the equalization patterns to your preference.

• Once you have made adjustment, it is memorized for each source.

Equalization adjustment—DEQ 63HZ, DEQ250HZ,

DEQ 1KHZ, DEQ 4KHZ, DEQ16KHZ

You can adjust five frequencies (63 Hz, 250 Hz, 1 kHz,

4 kHz, 16 kHz) within the range of –8 dB to +8 dB in 2 dB

steps.

•When adjustment is made, the DIGITAL EQ indicator lights

up on the display.

To flat the equalization pattern, set all the frequencies to

“0 (0 dB)” in step 4 of “Basic Procedure” (on page 21). The

DIGITAL EQ indicator goes off from the display.

Note:

The equalization patterns affect the front speaker sounds only.

Adjusting the Speaker Output Levels

You can adjust the speaker output levels.

• Once you have made adjustment, it is memorized for each source.

Adjustable speakers—SUBWFR LEVEL,

FRONT L LEVEL, FRONT R LEVEL, CENTER LEVEL,

SURR L LEVEL, SURR R LEVEL

You can adjust the connected speakers’ output levels within the

range of –10 dB to +10 dB.

Note:

If you have deactivated a speaker (see page 18), the output level

adjustment for the speaker is not adjustable.

Adjusting the Sound Parameters for the

Surround and DSP Modes

You can adjust the Surround and DSP sound parameters to your

preference. (For Surround and DSP modes, see pages 23 and 26.)

Adjustable parameters

You can adjust the following parameters:

For DAP modes and Mono Film

• Once you have made adjustment, it is memorized for each

mode.

EFFECT: Adjust the effect level. As the number increases,

the effect becomes stronger. (Adjustable range: 1

to 5. Normally select “3.” )

For Surround and DSP modes (when the center speaker is

connected)

CENTER TONE: Adjust the center tone. As the number

increases, the dialogue becomes clearer so

that the human voices change from soft to

sharp. (Adjustable range: 1 to 5. Normally

select “3.”)

Note:

This setting is common to all Surround modes, and is memorized

separately for DSP modes.

Adjusting Sound

TEST

EFFECT

LEVEL

DISC

REC PAUSE

SURR R

SURR L

SUBWFR

CENTER

FRONT R

FRONT L

REW

TA/NEWS/INFO

For Pro Logic II Music only

PANORAMA CTRL: Select “PANORAMA ON” to add

“wraparound” sound effect with side-wall image.

•To cancel it, select “PANORAMA OFF.”

21-22_RX-5060B[C].p65 05.12.24, 12:2522

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-5062 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC RX-5062

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info