Bedienungsanleitung JVC RX-5062S (Seite 35 von 39) (Englisch)

708111

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s

components are preset in the remote control.

Tuner

You can always perform the following operations:

FM/AM: Alternate between FM and AM (MW).

After pressing FM/AM, you can perform the following operations

on a tuner:

1 – 10, +10: Select a preset channel number directly.

For channel number 5, press 5.

For channel number 15, press +10, then 5.

For channel number 20, press +10, then 10.

PTY SEARCH: Search for a program by PTY codes.

PTY 9,( PTY: Select the PTY codes.

DISPLAY MODE: Show the Radio Data System signals.

TA/NEWS/INFO: Select the Enhanced Other Networks data

type (TA, NEWS, INFO).

FM MODE: Change the FM reception mode.

CD player

After pressing CD, you can perform the following operations on a

CD player:

3: Start playing.

4: Return to the beginning of the current (or previous)

track.

¢: Skip to the beginning of the next track.

7: Stop playing.

8: Pause playing. To resume, press 3.

1 – 10, +10: Select a track number directly.

For track number 5, press 5.

For track number 15, press +10, then 5.

For track number 20, press +10, then 10.

For track number 30, press +10, +10, then 10.

Operating Audio Components

Sound control section (Amplifier)

You can always perform the following operations:

STANDBY/ON

AUDIO:

Turn on or off the receiver.

VOLUME +/–: Adjust the volume level.

MUTING: Turn on or off sound muting.

ANALOG/DIGITAL: Switch the analog and digital input

alternately.

DIMMER: Dim or brighten the display.

SLEEP: Set the Sleep Timer.

SURROUND: Turn on and select Surround modes.

DSP: Turn on and select DSP modes.

SURROUND/DSP OFF:

Turn off the Surround and DSP mode.

After pressing SOUND, you can perform the following operations

by using the number buttons:

FRONT L then LEVEL +/–: Adjust the left front speaker output

level.

FRONT R then LEVEL +/–: Adjust the right front speaker output

level.

CENTER then LEVEL +/–: Adjust the center speaker output level.

SURR L then LEVEL +/–: Adjust the left surround speaker

output level.

SURR R then LEVEL +/–: Adjust the right surround speaker

output level.

SUBWFR then LEVEL +/–: Adjust the subwoofer output level.

EFFECT: Adjust the effect level.

TEST: Turn on or off test tone output.

Note:

After adjusting sounds, press the corresponding source selection

button to operate your target source by using the number buttons;

otherwise, the number buttons cannot be used for operating your

target source.

IMPORTANT:

To operate JVC’s audio and video components using the supplied remote control:

• When using the remote control, aim the remote control directly at the remote sensor on each component, not on the receiver.

• Refer also to the manuals supplied with your components.

• Some JVC’s VCRs can accept two types of the control signals— remote code “A” and “B.” Before using this remote control, make sure

that the remote control code of the target VCR is set to code “A.”

Continued on the next page

31-34_RX-5062S[B].p65 05.12.16, 21:3831

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-5062S Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC RX-5062S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info