Bedienungsanleitung JVC RX-6000VBK (Seite 26 von 39) (Englisch)

602848

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

English

4. Adjust the speaker output levels.

• To adjust the center speaker level, press

CENTER –/+ (from –10 dB to +10 dB).

• To adjust the left rear speaker level, press

REAR•L –/+ (from –10 dB to +10 dB).

• To adjust the right rear speaker level, press

REAR•R –/+ (from –10 dB to +10 dB).

5. Press TEST again to stop the test

tone.

JVC Theater Surround adjustments

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 12).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NONE.” See page 12.

• You cannot adjust the center speaker output level and center tone

when you have set “CENTER SPK” to “NONE.” See page 12.

From the remote control:

1. Press SURROUND MODE

repeatedly until “THEATER”

appears on the display.

• The Ÿ PRO LOGIC and DSP indicators

also light up on the display.

2. Press SOUND.

The 10 keys are activated for sound adjustments.

3. Press TEST to check the speaker

output balance.

“TEST TONE L” starts flashing on the

display, and a test tone comes out of the

speakers in the following order:

Notes:

• You can adjust the speaker output levels without outputting the

test tone.

• No test tone comes out of the center speaker when “CENTER

SPK” is set to “NONE” (see page 12).

• No test tone comes out of the rear speakers when “REAR SPK”

is set to “NONE” (see page 12).

+10

– REAR•R +

ENTER

– REAR•L +

– CENTER +

TEST

TEST TONE L

(Left front speaker)

TEST TONE LS

(Left rear speaker)

TEST TONE RS

(Right rear speaker)

TEST TONE C

(Center speaker)

TEST TONE R

(Right front speaker)

SURROUND

MODE

SOUND

TEST

SURROUND

On the front panel:

You can also use the buttons on the front panel to adjust the

Surround modes. However, no test tone is available when using the

buttons on the front panel. So, make adjustments while listening to

the sound of the source played back.

1. Press SURROUND to active an

appropriate Surround mode —

PRO LOGIC, DOLBY DIGITAL

or DTS SURROUND.

• Each time you press the button, the Surround mode turns on

and off alternately.

• When “PRO LOGIC” is selected, the Ÿ PRO LOGIC

indicator lights up on the display.

2. Adjust the speaker output levels.

1) Press ADJUST repeatedly until one of

the following indications appears on

the display.

“CENTER LEVEL”:

To adjust the center speaker level.

“REAR L LEVEL”:

To adjust the left rear speaker level.

“REAR R LEVEL”:

To adjust the right rear speaker level.

• Once you have pressed ADJUST,

MULTI CURSOR % / ﬁ can be also

used for selecting the speaker.

2) Press MULTI CURSOR @ / # to

adjust the selected speaker output level

(from –10 dB to +10 dB).

3) Repeat 1) and 2) to adjust the other

speaker output levels.

MULTI CURSOR

ADJUST

EN18_25.RX-6000V[J] 99.12.16, 1:10 PM23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-6000VBK Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info