Bedienungsanleitung JVC RX-8020VBK (Seite 25 von 64) (Englisch)

546765

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

1 Setting the Speakers

To obtain the best possible surround sound from the Surround and

DSP modes, you have to register the setting about the speaker

arrangement after all connections are completed.

Subwoofer setting—SUBWOOFER

[On-screen display] [Front panel]

Select whether you have connected a subwoofer or not.

YES : Select this when a subwoofer is connected.

NO : Select this when no subwoofer is used.

Note:

If you have selected “NO” for the subwoofer, you cannot use

SUBWOOFER OUT ON/OFF on the front panel.

Sizes for front speakers, center speaker, surround

speakers, and surround back speakers–—FRONT

SPK, CENTER (CNTR) SPK, SURR SPK, S BACK

(SBACK) SPK

[On-screen display] [Front panel]

Select the sizes for each connected speaker.

LARGE : Select this when the speaker size is relatively large.

SMALL : Select this when the speaker size is relatively small.

NONE : Select this when you have not connected a speaker.

(Not selectable for the front speakers)

Notes:

• Keep the following comments in mind as reference when

adjusting.

– If the size of the cone speaker unit built in your speaker is

larger than 12 cm (4

inches), select “LARGE,” and if it is

smaller than 12 cm (4

inches), select “SMALL.”

• If you have selected “NO” for the subwoofer setting, you can

only select “LARGE” for the front speakers.

• If you have selected “SMALL” for the front speakers, you

cannot select “LARGE” for the center, surround, and surround

back speakers.

• If you have selected “SMALL” for the surround speakers, you

cannot select “LARGE” for the surround back speakers.

• If you have selected “NONE” for the surround speakers, the

surround back speakers are fixed to “NONE.”

Surround back speakers quantity—S BACK (SBACK)

OUT

[On-screen display] [Front panel]

Select the surround back speakers quantity.

2SPK : Select this to use 2 surround back speakers.

1SPK : Select this to use 1 surround back speaker.

Notes:

• If you have selected “NONE” for the surround back speakers

(see the left), this setting cannot be available.

• If you have selected “1SPK” for the surround back speaker

quantity, connect the surround back speaker to the PRE OUT

SURR BACK L (left) jack.

Selecting surround speakers to use—SURR CH (OUT)

[On-screen display] [Front panel]

Select the surround speakers to activate when playing back

5.1-multi-channel software.

SURR : Select this to use only the left and right

surround speakers.

SBACK : Select this to use only the surround back

speakers.

SURR+SBK : Select this to use both the surround speakers

(S+SBK) and surround back speakers.

Notes:

• If you have selected “NONE” for the surround back speakers

(see the left), this setting is skipped.

• If you have selected “1SPK” for the surround back speaker

quantity, this setting is skipped. The surround channels’ signals

are output through the surround speakers.

• This setting is ignored when performing 6.1-channel

reproduction.

EN21-26.RX-8020V[UJ]_f 02.5.22, 9:47 AM22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-8020VBK Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info