Bedienungsanleitung JVC RX-E100RSL (Seite 42 von 50) (Englisch)

469766

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

Press ADJUST.

The CONTROL buttons now work for sound

adjustments.

Press CONTROL ∞ (or 5) repeatedly until one

of the following indications (with the current

setting)

* appears.

REAR L : To adjust the left rear speaker output level

(from –10 to +10).

REAR R : To adjust the right rear speaker output level

(from –10 to +10).

EFFECT : To adjust the DSP effect level. As the number

increases, the effect becomes stronger (normally set

it to “EFFECT 3”).

* “0” is the initial setting for the speaker output levels, and

“EFFECT 3” is for the DSP effect level.

If you have already changed the setting, another setting will be

shown.

Press CONTROL 3 (or 2) to make an

adjustment.

• When adjusting the speaker output levels, make adjustments

so that the sound level of the selected speaker is set at the

same level as that of the front speakers.

Repeat steps

and

to make other

adjustments.

To cancel DAP Mode

Press DSP MODE repeatedly so that “STEREO” appears on the

display. The DSP indicator goes off.

CENTER : To adjust the center speaker output level

(from –10 to +10).

REAR L : To adjust the left rear speaker output level

(from –10 to +10).

REAR R : To adjust the right rear speaker output level

(from –10 to +10).

EFFECT : To adjust the DSP effect level. As the number

increases, the effect becomes stronger (normally set

it to “EFFECT 3”).

* “0” is the initial setting for the speaker output levels, and

“EFFECT 3” is for the DSP effect level.

If you have already changed the setting, another setting will be

shown.

Press CONTROL 3 (or 2) to make an

adjustment.

• When adjusting the speaker output levels, make adjustments

so that the sound level of the selected speaker is set at the

same level as that of the front speakers.

Repeat steps

and

to make other

adjustments.

To cancel Theatre Surround

Press DSP MODE repeatedly until “STEREO” appears on the

display. The PRO LOGIC and DSP indicators go off.

Using DAP Modes (Front Panel)

A DAP mode cannot be used with another DSP mode. Once one of

the DAP modes is activated, the other DSP mode in use will be

canceled.

• You have to make this adjustment for each source.

• You cannot use the DAP modes if no rear speakers are connected.

Select and play stereo analogue software or

Linear PCM digital software.

Press DSP MODE repeatedly until one of the

DAP modes appears on the display.

The DSP indicator lights up on the display.

Ex.: When adjusting the left rear speaker output level

Creating Realistic Sound Fields

ANALOG

PRO LOGIC

SUBWFR LFE

VOL

DGTL AUTO

INPUT ATT

DSP

LCR

LS S RS

LPCM

DOLBY D

DTS

Ex.: When adjusting the center speaker output level

CONTROL

ADJUST

ANALOG

PRO LOGIC

SUBWFR LFE

VOL

DGTL AUTO

INPUT ATT

DSP

LCR

LS S RS

LPCM

DOLBY D

DTS

CONTROL

ANALOG

SUBWFR

VOL

DSP

LS S RS

(back to the begining)

DSP

MODE

ANALOG

PRO LOGIC

SUBWFR LFE

VOL

DGTL AUTO

INPUT ATT

DSP

LCR

LS S RS

LPCM

DOLBY D

DTS

CONTROL

EN30-39.RX-E100RSL[B]_4 01.3.7, 8:33 PM39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC RX-E100RSL Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC RX-E100RSL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info