Bedienungsanleitung JVC SP-UXDM8 (Seite 39 von 48) (Englisch)

56519

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Setting Playback Timer

You can use Playback Timer for all the sources.

• You can store three timer settings in total of Recording

Timer (see page 34) and Playback Timer.

• To exit from the timer setting, press CLOCK/TIMER as

required.

• To correct a mis-entry during process, press CANCEL.

You can go back to the previous step.

1 Prepare the playback source.

• When you want to play back the radio broadcast (FM

or AM):

Preset the desired station. (See “To preset the stations”

on page 7.)

• When you want to play back the disc:

Insert a disc. (See “To insert a disc” on page 8.)

• When you want to play back the USB device:

Connect the USB device (see page 8).

• When you want to play back an iPod:

Before connecting the iPod, switch the charge mode to

“ON.”

Connect an iPod (see page 10), and pause playback at

the beginning of the desired track (see “To play back an

iPod” on page 10).

• When you want to play back the portable audio

device:

Connect the portable audio device to the AUX jack (see

page 11), and set the timer on that device.

2 Make the timer setting, following steps 2 to 7 of

Recording Timer on page 36 to 37.

3 Select “PLAY TIMER.”

4 Select the source to play.

• When you want to listen to the radio broadcast (FM

or AM):

Select the preset number of the desired station.

• You can also use the number buttons to select the

preset number.

• When you want to play back a disc, built-in memory

or USB device:

Select the group number, then the track number of the

desired track.

• When the loaded disc is an audio CD, simply select the

track number, then press SET.

5 Adjust the playback volume.

• You can also use the number buttons to adjust the

playback volume.

6 Turn off the System.

To cancel Playback Timer

In step 2 on page 34, select the timer number you want to

cancel, then press CANCEL.

• Even when you cancel Playback Timer, the setting remains

stored.

To activate Playback Timer again

In step 2 on page 34, select the timer number you want to

activate, then press ENTER. The settings appear on the

display. After you confirm it, turn off the unit.

How Playback Timer works

Once the Playback Timer has been set, the indicator

and timer number (1, 2, or 3) indicator are lit on the

display. Playback Timer is activated at the same time

everyday until the timer is turned off manually.

• Playback Timer starts working only when the System is

turned off (on standby).

When the start time comes

The System turns on, tunes in to the specified station or

starts playing the specified source, and sets the volume

level gradually to the preset level after about 30 seconds.

When the end time comes

The System stops playback, and turns off (standby).

• The timer setting remains in memory until you change it.

Remote

ONLY

INFO

UX-DM8[U].book Page 36 Monday, June 4, 2007 8:20 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC SP-UXDM8 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info