Bedienungsanleitung JVC UXH350 (Seite 19 von 28) (Englisch)

29948

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Tuning in to a Station

Press FM/AM to select either “FM”

or “AM.”

The unit automatically turns on and tunes in to

the previously received station—either FM or AM.

• Each time you press the button, the band alternates

between FM and AM.

• If the station previously selected is stored in a preset

number, the preset number will appear instead of “FM”

or “AM.”

Press and hold ¢ or 4 (or

UP ¢ or DOWN 4 on the

unit) for more than 1 second.

• ¢ (UP ¢): Increases the frequencies.

• 4 (DOWN 4): Decreases the frequencies.

The unit starts searching for stations and stops when a

station of sufficient signal strength is tuned in.

• If an FM program is broadcast in stereo, the ST (stereo)

indicator lights up on the display (only when the

reception is good).

Listening to FM and AM Broadcasts

FM/AM

PRESET

GROUP

PRESET

GROUP

DOWN

MHz

FM MODE

Setting the Tuner Interval Spacing

You can only change the FM or AM tuner interval spacing

while tuning in to a FM or AM station.

On the unit ONLY:

Press FM/AM to select either “FM”

or “AM.”

Turn the VOLUME + / –

control while pressing and

holding 7.

As you turn the VOLUME + / – control,

the interval spacing for the selected band

alternates as follows:

• For FM: 50 kHz* and 100 kHz

• For AM: 9 kHz* and 10 kHz

* Initial setting

When you change the setting

The preset stations for both FM and AM are erased. You will need to

preset the stations again. (See the right column.)

FM/AM

DOWN

4 7 ¢

VOLUME

To stop during searching, press ¢ or 4 (or UP ¢ or

DOWN 4 on the unit).

When you repeatedly press ¢ or 4 (or UP ¢ or

DOWN 4 on the unit)

The frequency changes step by step.

To change the FM reception mode

On the remote control ONLY:

When an FM stereo broadcast is hard to

receive or noisy, press FM MODE so that the

“MONO” appears on the display. The MONO

indicator also lights up. Reception will improve.

To restore the stereo effect, press FM MODE again so that

“STEREO” appears on the display and the MONO indicator

goes off. In stereo mode, you can hear stereo sound when a

stereo program is broadcast.

The stereo effect also restores when:

• Changing the band (FM or AM).

• Changing the station frequency.

• Changing the playing source.

• Turning off (or on) the unit.

Presetting Stations

You can preset 25 FM and 15 AM stations manually.

In some cases, test frequencies have been already stored

for the tuner since the factory examined the tuner preset

function before shipment. This is not a malfunction. You

can preset the stations you want into memory by following

the presetting method.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start again from step

On the remote control ONLY:

Tune in to the station you want to preset.

• See “Tuning in to a Station” on the left column.

Press SET.

“00” starts flashing on the display.

SET

MHz

PRGM

Continued

16-17_UX-H350[UJ]2.p65 5/19/04, 12:40 PM16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC UXH350 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info