Bedienungsanleitung Kalkhoff 2021 (Seite 37 von 70) (Englisch)

778421

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Originalbetriebsanleitung Allgemein EN-37

24. Bicycle shifter

Warning

Seriousfallsandaccidentscausedbyinsucientbicycle

control.

▪If the shifter parts are loose, worn, damaged,

incorrectly adjusted, make unusual noises, the

gearchange does not work properly or other problems

occur, have the shifter checked and if necessary

repaired in a specialist workshop.

You can use the gear shift to change the transmission ratio

of the drive, so that you can ride at a comfortable pace with

less eort. You can change gears by moving the control el-

ements (gear levers, twist grips, buttons, …) on the handle-

bars. The lower the number shown on the control element,

the easier it is to pedal. The higher the number shown on

the control element, the greater the pedalling resistance.

Low gears are useful for riding up a mountain, so that you

can reach the peak with little eort. On a straight level

stretch, medium gears are the right choice to achieve and

maintain a higher speed without having to pedal too much.

High gears are recommended for downhill stretches.

Fig. 58a Uphill:

low gears

Fig. 58b Level:

medium gears

Fig. 58c Downhill:

high gears

away. It therefore makes sense to perform regular visual

checks of the state of wear. You can recognise the state of

wear with a marking, e.g., grooves in the brake lining. On

Shimano brake shoes, a wear line is visible on the brake

pads. This must not be shorter than a certain minimum

length. With Magura, the grooves in the lining must still be

visible from the outside. If the wear line or grooves are no

longer visible, the brake pads must be replaced. Have this

done in a specialist workshop.

Fig. 57 Shimano brake shoeFig. 56 Magura brake shoe

23.7 Cleaning and care

The brake grips can be cleaned with a slightly damp cloth.

Rim brake: The rims can be cleaned with a sponge and

soapy water.

Disc brakes: Clean the disc brakes with a sponge and soapy

water. If they are very dirty, we recommend using a little

brake cleaner on a rag.

24.1 Adjusting the position of the control

elements

Information

The gear levers should be positioned at the same angle

as the brake levers.

1. Loosen the fastening screw by turning it one or

two turns counterclockwise.

2. To move the control element, move it to the left or

right into the desired position.

3. To adjust the angle of the control element, place

one or two ngers on the gear lever. Now turn the

grip downward until your nger, wrist and forearm

are in a line.

4. Then tighten the fastening screw clockwise to the

specied torque using a torque wrench

 13. Tightening torques for threaded connections

Page EN-19.

Fastening

screw

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kalkhoff 2021 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kalkhoff 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info