Bedienungsanleitung Kalorik KA CV 15 (Seite 6 von 24) (Englisch, Portugiesisch, Spanisch)

491358

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

6 KA CV 15 - 070711

Assembly page 6/24

Fax +32 2 359 95 50

TECHNICAL SPECIFICATIONS

MODEL

FINS

POWER

MEDIUM

HIGH

KA CV 15-6

600W

900W

KA CV 15-8

800W

1200W

KA CV 15-10

1000W

1500W

CONNECTION TO THE MAIN SUPPLY

Caution: We cannot be held responsible for any damage due to the wrong use or the non-

observance of this instruction manual.

The convection heater should only be connected to an earthed socket installed in

accordance with the regulations. Make sure that the supply voltage corresponds with the

voltage marked on the rating label.

This product complies with CE-directives.

BEFORE THE FIRST USE

Before using the convection heater for the first time, you must either attach the feet to the

base of the unit or mount the appliance on the wall.

Floor-standing (see page 4)

Attach each foot underneath the appliance by tightening the two small screws provided in

the holes foreseen to this effect as indicated on page 3. Make sure to install the appliance at a

minimum distance of 50 cm to other objects or walls.

Wall-mounting (see pictures page 4)

Caution:

 There should be a distance of at least 15 cm between the lower part of the

appliance and the floor. This distance should not exceed 30 cm. Make sure you

mount the heater at a minimum distance of 15 cm from other objects.

 Feet must be removed before mounting the appliance on the wall

1. Fit the 2 upper brackets inside the holes located at the 2 far ends of the back of the

appliance (see Fig. 1).

2. Measure the distance between the slots of the two brackets (see Fig. 2).

3. Mark 2 dots at the same distance on the wall. Place the brackets facing the dots (larger

side towards the wall) and mark two other dots for the lower slots of the upper brackets.

Drill 4 holes in the wall and insert a plug in each hole you just drilled. Make sure the

distance between the 2 dots you marked for one bracket is the same as the one between

the 2 slots (see Fig. 3).

4. Attach the two brackets on the wall with the screws supplied

5. Attach the appliance on the wall. To do so, hold it in such way that the holes are facing

the brackets and slide it down until it rests on the 2 upper brackets.

6. As soon as the appliance is positioned correctly, attach the two lower brackets

underneath the appliance, take a pencil and mark a dot in the slot of each bracket

situated underneath the appliance.

7. Then take off the appliance.

8. Drill a hole in the wall on each dot you just marked and insert a plug in each hole.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kalorik KA CV 15 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info