Bedienungsanleitung Kalorik KA CV 9 (Seite 5 von 16) (Englisch, Französisch, Portugiesisch)

491352

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

5 KA CV 9 - 080529

Assembly page 5/16

Fax +32 2 359 95 50

CONNECTION TO THE MAINS SUPPLY

Caution: We cannot be held responsible for any damage due to the wrong use or the non-

observance of this instruction manual.

The convection heater should only be connected to an earthed socket installed in

accordance with the regulations. Make sure that the supply voltage corresponds with the

voltage marked on the rating label.

This product complies with CE-directives.

BEFORE THE FIRST USE

Before using the convection heater for the first time, you must either attach the feet to the

base of the unit or mount the appliance on the wall.

Floor-standing (see page 3)

Attach each foot underneath the appliance by tightening two screws provided in the holes

foreseen to this effect as indicated on page 3. Make sure to install the appliance at a minimum

distance of 50 cm to other objects or walls.

Wall-mounting (see pictures page 3)

Caution: - there should be a distance of at least 40 cm between the lower part of the

appliance and the floor.

- the feet must be removed before mounting the appliance on the wall

1. Measure the distance between the two slots situated at the back of the appliance (see

picture A)

2. Drill two holes at the same distance in the wall and insert a plug in each hole you just

drilled. Place the brackets facing the holes as indicated on picture B and attach them in

this position with the screws supplied.

3. Before attaching the appliance on the brackets, attach the two other brackets

underneath the appliance as indicated on picture C.

4. Attach the appliance on the wall. To do so, hold it in such way that the slots are facing the

brackets, insert the appliance halfway onto the brackets until the appliance can go down

into the grooves of the brackets.

5. As soon as the appliance is positioned correctly, take a pencil and mark a dot in the hole

of each bracket situated underneath the appliance.

6. Then take off the appliance by proceeding the other way around compared to point 4

above.

7. Drill a hole in the wall on each dot you just marked and insert a plug in each hole.

8. Attach the appliance back on the wall as indicated in point 4, insert screws through the

brackets underneath the appliance and tighten without forcing.

OPERATION

When the appliance is switched on for the first time, a slight smell may be emitted. Please

ensure sufficient ventilation. This smell will disappear very quickly.

With the power switches you can regulate the heating intensity. The thermostat allows you to

keep a constant room temperature.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kalorik KA CV 9 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info