Bedienungsanleitung Kalorik TKG VT 1000 (Seite 9 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

487926

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

9 TKG VT 1000 - 101124

Assembly page 9/36

Fax +32 2 359 95 50

ASSEMBLY

1. Place stand A (18) on stand B (19) to form an X-base.

2. Place the lower pipe (15) with pipe support (17) on the X-base and fix it with four screws

provided.

3. Loosen and remove the pipe connector (14) from the lower pipe (15). Slide the plastic

base cover (16) over the lower pipe on the base. Extend the upper (inner) pipe (13) and

slide the pipe connector (14) over the upper pipe onto the lower pipe and tighten.

4. Attach the motor (11) with speed regulator (12) onto the upper pipe (13). Ensure the

speed regulator is pushed fully onto the upper pipe and secured with the screws provided.

5. Loosen the guard mounting ring (6) from the motor housing (9).

6. Position the rear guard (7) firmly against the motor housing (9) and fasten by turning the

guard mounting ring (6) clockwise tightly.

7. Push the blade (5) along the motor shaft (8). Fasten it firmly with the cap (4) by turning

counter clockwise.

8. Hang the front guard (2) to the rear guard (7) with the position fixer (3) provided at the

front guard rim, and then clamp together with the clips provided.

9. To ensure that it is impossible to have access to the fan blade without using a tool, a screw

is provided with this appliance in order to attach both parts of the mesh guard together.

This screw must be tightened on the lower part of the guards. We will not be responsible

for any injuries in case this screw had not been tightened before using the appliance.

10. To change the height, loosen the pipe connector (13) and slide the upper pipe to a

suitable height. Then tighten the pipe connector (14) again.

OPERATION

 This appliance is equipped with 3 ventilation speeds. To switch on the appliance, press

one of the speed knobs. To switch it off, press “0”.

Speed settings:

0 = OFF

1 = Low

2 = Medium

3 = High

 This appliance also has an oscillation function:

 Push the oscillation knob (10) to switch on the oscillation.

 Pull the oscillation knob (10) to stop.

 It is also possible to tilt the upper part of the appliance in order to adjust the airflow

direction vertically.

CLEANING AND CARE

 Always disconnect the power supply cable from the power supply before carrying out any

cleaning operation.

 To remove dirt from the plastic surfaces, use a soft damp cloth. Use a vacuum cleaner to

remove the dust from the guards without having to disassemble them.

 Never immerse the fan in water or any other liquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kalorik TKG VT 1000 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info