Bedienungsanleitung Karcher B 110 R (Seite 24 von 452) (Alle Sprachen)

804757

Zoom out

Zoom in

Vorherige Seite

1/452

Nächste Seite

24 English

Note

The travel direction can be changed while

driving. This means that very dull spots can

be polished by moving back and forth sev-

eral times.

1. Assume a seated position.

2. Insert the Intelligent Key.

3. Turn the safety switch to "1".

4. Set the program selector switch to

"TRANSPORT MODE".

5. Set the direction of travel using the drive

direction button on the control panel.

6. Specify the travel speed by pressing the

accelerator pedal.

7. Release the accelerator pedal.

The device stops.

The driving motor is switched off in the event of

an overload. A fault message appears on the

display. If the controller overheats, the affected

power unit is switched off.

8. Allow the device to cool down for at least

15 minutes.

9. Set the program switch to “OFF”, wait

briefly and set to the desired program.

Filling with fresh water

Filling with fresh water via the filling

system

1. Connect the water hose to the connec-

tion nozzle of the filling system (maxi-

mum water temperature 50 °C).

2. Open the water inlet.

3. Monitor the device, the automatic filling

system interrupts the water supply when

the fresh water tank is full.

4. Close the water inlet.

5. Remove the water hose.

Filling with fresh water

1. Open the fresh water tank cap.

2. Fill fresh water (max. 50 °C) to the lower

edge of the filling nozzle.

Note: The fresh water hose can be

clamped with the hose holder during fill-

ing.

3. Close the fresh water tank lock.

Filling with detergent

Notes on detergents

몇WARNING

Unsuitable detergents

Health risk, damage to the device

Use only recommended detergents. The

operator carries all increased risks relating

to operational safety and increased risk of

accidents if using other detergents.

Use only detergents free of chlorine, sol-

vents, salt and hydrofluoric acid.

Adhere to the safety instructions stated on

the detergent packaging.

Note

Do not use heavily foaming detergent.

Recommended detergents

Filling detergent via the dosing device

Only with DOSE variant:

Detergent is added to the fresh water on

the way to the cleaning head by a dosing

device.

1. Unlock the waste water tank and pivot it up.

2. Fill the detergent canister with detergent.

3. Pivot the waste water tank forwards.

Note

A maximum of 3% detergent can be added

with the dosing device. If the dosage is

higher, the detergent must be added to the

fresh water tank.

Filling the detergent into the fresh water

tank

1. Fill the detergent into the fresh water tank.

Note: The lid for the filling hole of the

fresh water tank can be used to measure

the detergent. It has a measuring scale

marked on the inner side.

Adjusting parameters

1. Set the program switch to the desired

cleaning program.

2. Turn the Info button until the desired pa-

rameter is displayed.

3. Press the Info button.

The adjusted value flashes.

4. Set the desired value by turning the Info

button.

5. Confirm the changed setting by pressing the

Info button or wait until the set value is auto-

matically accepted after 10 seconds.

Yellow Intelligent Key

The yellow Intelligent Key authorizes func-

tions that are required for the cleaning task.

The parameters for the various cleaning pro-

grams are preset in the device. Individual pa-

rameters can be changed depending on the

authorization of the yellow Intelligent Key.

The display texts for parameter setting are

largely self-explanatory.

"FACT" parameters (only available with R

cleaning head):

●"Fine Clean": Low brush speed for re-

moving grey film from fine stone.

●"Whisper Clean": Medium brush speed

for maintenance cleaning with reduced

noise level.

●"Power Clean": High brush speed for

polishing, crystallizing and sweeping.

Adjusting the suction bar

Adjusting the inclination

The inclination must be adjusted so that the

suction lips of the suction bar make even

contact with the floor over the entire length

of the suction bar.

1. Park the device on a surface without a

slope.

2. Turn the program switch to the "Vacu-

um" position.

3. Drive the device a small distance for-

wards.

4. Read the spirit level.

1Screw

2Nut

3Spirit level

5. Unscrew the nut.

6. Adjust the screw so that the spirit level

indicator is between the two lines.

7. Tighten the nut.

8. To check the new setting, move the de-

vice forward again a short distance. Re-

peat the adjustment process if

necessary.

9. Turn the key-operated switch to "OFF".

Adjusting the height

The height adjustment affects the bending

of the suction lips on contact with the floor.

Note

Standard setting: 3 washers above, 3

washers below the suction bar.

Uneven floor: 5 washers above, 1 washer

below the suction bar.

Very smooth floor: 1 washer above, 5

washers below the suction bar.

1. Unscrew the nuts.

1Nut

2Washer

3Spacer roller with holder

Application Detergent

Maintenance cleaning of all

water-resistant floors

RM 746

RM 756

RM 780

Maintenance cleaning of

polished hard surfaces (e.g.

granite)

RM 755 es

Maintenance cleaning, in-

termediate cleaning and ba-

sic cleaning of industrial

floors

RM 69 ASF

Maintenance cleaning and

basic cleaning of fine stone

tiles

RM 753

Maintenance cleaning of

tiles in sanitary areas

RM 751

Coating removal on all alka-

line-resistant floors (e.g. PVC)

RM 752

Coating removal on linole-

um floors

RM 754

Karcher B 110 R Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info