Bedienungsanleitung Karcher BP 2.000-18 Barrel (Seite 11 von 124) (Alle Sprachen)

803812

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

English 11

Connecting the extension hose / accessories

1. Connect the extension hose with special accesso-

ries (not included in scope of delivery) to the hose

coupling.

Illustration I

Installing the battery pack

1. Open the protective bonnet upwards.

2. Push the battery pack into the mounting in the de-

vice until it audibly latches into place.

Illustration J

3. Close the protective bonnet.

Operation

DANGER

Danger of death from electric shock.

Danger of death from electric shock if live parts or the

feed fluids are touched.

Do not touch any live parts or the feed fluid.

Note

For the pump to suction independently, it must be at

least 3 cm in the liquid.

If the requirements for the pumping process (water level

position / level switch) are guaranteed, the pump starts

immediately after inserting the battery pack.

1. Press the unit trigger.

2. Pump switches on.

Ending operation

Note

Internal soiling can accumulate as deposits and lead to

malfunctions.

1. Flush the pump with clear water after each use.

This is especially true after transporting chlorinated

water or other liquids that leave residues.

2. Switch off the pump by pressing the trigger.

3. Remove the battery pack.

Transport

몇WARNING

Switch the device off, allow it to cool down and remove

the battery pack before storage or transportation.

Carry the device.

ATTENTION

Loose cable and hoses lying on the ground

Danger of tripping

Watch out the cables and hoses when relocating the de-

vice in mobile operation.

Transport the device in a vehicle.

a Secure the device against slipping and tipping

over.

Storage

ATTENTION

Danger of frost

Incompletely emptied devices can be destroyed by

frost.

Completely empty the device and accessories.

Protect the device from frost.

Care and service

The device is maintenance-free, i.e. you do not need to

perform periodic maintenance work.

Flushing the pump

1. Flush the pump with clear water if water with addi-

tives has been delivered.

Cleaning the pre-filter

Check the pre-filter for contamination and clean if nec-

essary.

Illustration K

1. Remove the pre-filter.

2. Clean the pre-filter under running water.

3. If necessary, flush any dirt residues out of the pump.

ATTENTION

Use of unsuitable lubricant

Damage to the seals

Use the grease (6.288-143.0) available from Kärcher

Service.

Use only grease free of mineral oil for the seals.

4. Lubricate the seals if the connections do not move

freely.

5. Fit the pre-filter into the filling nozzle without using

unnecessary force. Ensure the correct installation

position (cutouts).

Troubleshooting guide

Malfunctions often have simple causes that you can

remedy yourself using the following overview. When in

doubt, or in the case of malfunctions not mentioned

here, please contact your authorised Customer Service.

Pump is running, but not delivering

Dirt particles block the suction area.

1. Clean the suction area.

Air in the pump

1. Switch the pump switch on and off several times un-

til liquid is sucked in.

(Only for manual operation) water table level below min-

imum level

1. If possible, immerse pump deeper in feed fluids.

Compressed air hose blocked

1. Clean the compressed air hose.

The pump does not start up or stops suddenly dur-

ing operation.

Power supply interrupted

1. Check whether the battery is correctly inserted.

Battery can no longer be charged

1. Battery must be replaced with a new one.

Thermal protection switch in the motor has switched off

the pump due to overheating of the motor.

1. Let the pump cool down, clean the suction area, pre-

vent dry running.

Remove any dirt particles trapped in the suction area.

1. Clean the suction area.

Battery does not charge

Charger or mains cable not connected correctly

1. Check for correct connection between battery and

charger.

2. Check the connection of the mains cable to the

socket.

The battery can no longer be charged.

1. Battery must be replaced with a new one.

Pump capacity decreases

Suction area clogged

1. Clean the suction area.

Pumping capacity too low

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher BP 2.000-18 Barrel Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info