Bedienungsanleitung Karcher BP 3.200 Home (Seite 9 von 132) (Alle Sprachen)

803817

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

10 English

Device description

The maximum amount of equipment is described in

these operating instructions. Depending on the model

used, there are differences in the scope of delivery (see

packaging).

For the illustrations, refer to the graphics page

Illustration A

1Connection adapter with integrated check valve

2Sealing plug

3Connection G 1 (33.3mm) suction line (inlet)

4Filling nozzle with cap

5Connection G 1 (33.3mm) pressure line (outlet)

6Connection adapter for pumps G 1

7ON/OFF switch

8Pressure indicator

9Stand with elongated hole for screwing

10 Air valve (car valve) with cap

11 Power supply cable with plug

12 Drain screw

Startup

We recommend using only original Kärcher suction hos-

es, filter components and hose connections. Using

components from other manufacturers can lead to mal-

functions when sucking the feed fluid, especially when

using bayonet connection systems.

Before initial startup

Preparation

●Before initial startup, check the pressure of the air

filling in the storage tank. If necessary, top up to 2.0

bar with a commercially available air pump when

switched off/depressurised.

Illustration B

●Secure the device against slipping, screw it down if

necessary.

●Remove the sealing plug.

●Screw the connection adapter with integrated check

valve into the suction connection of the pump (inlet).

Illustration C

Note

If the water is dirty, we recommend fitting a pre-filter

(see Special accessories) between the check valve and

the suction hose.

Illustration D

1 Connect vacuum-proof suction hose with integrated

backflow stop to suction side. (Available as an spe-

cial accessory).

2 Screw the connection adapter into the pressure con-

nection of the pump (outlet).

3 Connect the pressure line.

4 Open the filling nozzle cap.

Illustration E

●Fill with water until it overflows.

Illustration F

●Screw the cap tightly onto the filling nozzle.

●Open existing stop valves in the pressure line.

Note

Even minor leaks lead to malfunctions.

●In case of leaks, seal all connections with a suitable

sealant (e.g. Teflon tape) to avoid malfunctions due

to leakage or air intake.

Permanent installation

In a permanent installation, the pump can be screwed to

a suitable surface.

●Screw the pump tightly to a level surface using suit-

able screws.

In addition, in the case of a fixed installation, it is recom-

mended to fit a flexible component on the pressure side,

such as a flexible pressure equalization hose (see Spe-

cial accessories), on the pressure side. This has the fol-

lowing advantages:

●Greater flexibility in erection and installation.

●Sound reduction since no vibration is transmitted in

to the pipes of the house water system.

●With smaller leaks, the pump switches less often.

Note

In order to simplify the subsequent draining and pres-

sure relief of the system, we recommend the installation

of a stop cock between the pump and the pressure line

(not included in the scope of delivery).

Closing the stop cock prevents water from flowing out of

the pressure line when the pump is drained.

Operation

1. Plug the mains plug into the socket.

2. Switch the device on with the ON/OFF switch.

Note

Pump starts immediately. Wait until the pump sucks in

and delivers evenly, then close the stop valves in the

pressure line.

After reaching the switch-off pressure, the pressure

switch switches off the motor. The storage tank is now

filled, the domestic water supply is ready for operation.

If there is no water supply, the switch-off pressure is not

reached and the pressure switch can no longer shut off

the device. This heats up the water in the pump head.

To prevent damage to the pump due to overheating, the

power supply is interrupted by the thermal switch in the

event of overheating. After cooling down, the power

supply is restored.

Note

The cooling time until the engine restarts can be up to

150 minutes.

We recommend the use of a dry-running protection de-

vice (see special accessories) for regular protection

against water shortage.

ATTENTION

Risk of injury, the system is pressurised!

When opening a pressurised system, you can be in-

jured by flying parts.

Depressurise the device before opening the connec-

tions (for pressure, see chapter Technical data)

Ending operation

1. Switch off the device at the ON/OFF switch.

2. Unplug the device at the mains plug.

Care and maintenance

DANGER

Danger of electric shock.

Always switch the device off and disconnect the mains

plug before working on the device.

The device is maintenance-free.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher BP 3.200 Home Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info