Bedienungsanleitung Karcher BP 4 (Seite 14 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657241

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

– 2

With the ON/OFF switch the following three operating

conditions can be switched:

In the automatic mode the house & garden pumps auto-

matically maintain the pressure in the system. If the

pressure falls below approx. 0.13 MPa (1.3 bar), the

pump is started. The pump is running as long as the flow

rate

> is approx. 60 l/h. If the withdrawal of water is complet-

ed, the pump goes into the stand-by mode after a short

stopping time. The system is now under pressure. In

case of water withdrawal and the resulting loss of pres-

sure the pump starts again.

The eco!logic models do not consume ener-

gy in the stand-by mode (input power = 0 W).

1Connection adapter for pumps G1

2 Connection G1 (33.3 mm) suction pipe (inlet)

3 Filling nozzle

4 Pre-filter and integrated check valve

5 Cover

6 2-way connection adapter for pumps G1

7 Connection G1 (33.3 mm) delivery line (output)

8 ON/OFF switch

9 Cable storage and mains cable with plug

10 Cable clip

11 Error display

A Error on suction side

B Error on delivery side

Illustration

 Screw the connection adapter in the suction con-

nection of the pump (inlet).

Tighten manually.

 Connect the vacuum-proof suction hose.

Note

In order to reduce the time required for suction to start

again, use a suction hose that is equipped with a back-

flow stop. This prevents the emptying of the suction

hose after use (see accessories).

Do not install the backflow stop directly on the pump

(suction or delivery side).

If sandy water is to be delivered, we strongly recom-

mend the use of an additional pre-filter (see optional ac-

cessories). Please install this filter on the suction side of

the pump, between the suction hose and the pump.

Please use original Kärcher suction pipes, filter compo-

nents and hose connections.

When using components of other manufacturers, mal-

functions during drawing in the delivery fluid may arise,

especially when using bayonet connection systems.

Do not use quick couplings, but screwed connections

with domestic or permanent installations.

Illustration

 Screw the connection adapter in the delivery con-

nection of the pump (outlet).

Tighten manually.

 Connect delivery line.

Illustration

The 2-way adapter allows the simultaneous operation of

two appliances (e.g. washing machine or sprinkler). It

can be mounted in a way that either both outlets are

used at the side or one outlet at the side and one outlet

at the top. If only one outlet is used, the outlet that is not

required can be closed by means of the accompanying

closing cap.

Illustration

 Unscrew the lid of the filler neck and fill in water up

to the brim.

 Manually screw the lid all the way to the stop on the

filler neck.

 Open existing shutoff valves in the pressure pipe.

Note

Even the smallest of leakage leads to malfunctioning.

With a permanent installation the pump can be screwed

onto a suitable surface.

Illustration

 Pull out and turn the rubber feet on both sides of the

casing.

 Reinsert the rubber feed into the casing.

 Use suitable screws to screw it onto a level surface.

In case of a permanent installation the installation of a

flexible component such as a flexible pressure compen-

sating hose (see optional accessories) on the pressure

side is recommended. This has the following benefits:

 More flexibility during set-up and installation.

 Noise reduction, as no vibrations are transferred to

pipes in the domestic water system.

 In case of small leaks, the pump does not switch as

often.

Note

To facilitate subsequent emptying and pressure release

of the system, we recommend the installation of a stop-

cock between pump and pressure line.

(not included in delivery)

By closing the shut-off valve when emptying the pump you

can prevent water from escaping from the pressure line.

Install a pressure equalization container (see special

accessories) in case of increased pressure reductions

due to leakages in the domestic system (pump switches

on regularly without water removal).

 Insert the mains plug into the socket.

 Switch on the appliance using the ON/OFF switch.

 Optimum convenience with operation in the auto-

matic mode.

Illustration

 In order to reduce the suction time, lift the delivery

hose approx. 1m.

 Wait till the pump sucks in and transports water uni-

formly

Operation

Settings

Switch position I/On

Continuous operation

Switch position 0/Off

Off

Switch position Auto

Automatic mode

System operation

Description of the Appliance

Preparing the Appliance

Permanent installation

Operation

14 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher BP 4 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info