Bedienungsanleitung Karcher BPE 4000-45 (Seite 15 von 78) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

519331

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

English 15

! Do not use the power cord to carry/

transport the machine.

! To separate the machine from the

mains, pull the plug and not the power

cord.

! Do not scrape the power cord across

sharp edges and ensure that it does not

get pressed.

! Do not operate the appliance continu-

ously in rain or during humid weather.

! The voltage indicated on the type plate

must correspond to the voltage of the

electrical source.

! To avoid risks, all repairs and replace-

ment of spare parts may only be carried

out by the authorised customer service

personnel.

! Do not use this pump as an immersion

pump.

! When using the pump near to pools,

garden ponds or fountains, observe a

minimum distance of 2m and safeguard

the device against slipping into the wa-

ter.

! Follow the rules for electrical safety of

equipment:

Only operate pumps near to pools, gar-

den ponds or fountains, if they are

equipped with an earth leakage circuit

breaker with a nominal error current of

max. 30 mA. It is not permitted to acti-

vate the pump, if persons are in the pool

or garden pond.

For safety reasons, we recommend that

you operate the appliance only via a

earth-leakage circuit breaker (max. 30

mA).

The electrical connection of the system

may only be performed by a qualified

electrician. Please follow the respective

national regulations!

In Austria pumps to be used in swim-

ming pools and garden ponds should be

equipped with a fixed connection line

according to ÖVE B/EN 60555 Part 1 to

3; power supply should be via a ÖVE-

tested isolating transformer whereby

the secondary nominal voltage should

not exceed 230V.

The automatic house water system main-

tains the pressure in the mains automatical-

ly. The pump is turned on if the pressure

falls below 0.16MPa (1.6 bar). The pump

remains turned on while water extraction is

detected by the flow meter (flow greater

than 300 l/h). Shortly after water extraction

is finished, the pump is turned off. The sys-

tem is now under pressure. In the case of

renewed water extraction and the resulting

pressure drop, the pump starts again.

The pump remains turned on for a 10s pe-

riod (“overpump time”) after the extraction

is finished to build up the required pressure

again. This period can be adjusted if need-

ed.

It should be increased if the pump is fre-

quently switched on and off (in the case of

reduced water extraction or system leak-

age).

Under ideal conditions, it can be reduced to

save energy.

Use the + / - buttons to adjust the overpump

time. The active light shows the current set-

ting (20s/10s/5s/3s).

In case of failure, the device is turned off

and the lights blink.

Restart the pump by simultaneously press-

ing the + / - buttons.

Operations

System operation

Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher BPE 4000-45 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info