Bedienungsanleitung Karcher g 4 10 m (Seite 14 von 208) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

381702

Zoom out

Zoom in

Vorherige Seite

1/208

Nächste Seite

- 6

Mount loose parts delivered with appliance prior

to start-up.

Illustrations on Page 2

Illustration

Î Fasten the transport handle to the frame.

Align the holes in such a way that the screws

can pass through and then fasten the nuts.

Illustration

Î Attach the accessories holder.

Illustration

Î Push the high pressure hose into the trigger

gun until it locks audibly.

Note: Make sure the connection nipple is

aligned correctly.

According to the applicable regula-

tions, the appliance must never be

used on the drinking water supply with-

out a system separator. Use a suitable

system separator manufactured by KÄRCHER;

or, as an alternative, a system separator as per

EN 12729 Type BA. Water flowing through a sys-

tem separator is considered non-drinkable.

Note: Impurities in the water can damage the

high-pressure pump and accessories. For pro-

tection, the use of the KÄRCHER water filter (op-

tional accessory, order no. 4.730-059) is

recommended.

Observe regulations of water supplier.

For connection values, see type plate/technical

data.

Î Use a fibre-reinforced water hose (not in-

cluded) with a standard coupling. (Minimum

diameter 1/2 inch (13 mm), minimum length

7.5 m).

Î Screw the coupling element (supplied) to the

water connection on the appliance.

Î Push the water supply hose onto the cou-

pling unit, then connect it to the water supply.

This high-pressure cleaner is suited to work with

the KÄRCHER suction hose with backflow valve

(Optional accessory, order no. 4.440-238) to

draw in surface water, e.g. from water butts or

ponds (see specifications for max. suction

height).

Î Fill the KÄRCHER suction hose with back-

flow valve with water, screw to water supply

and hang into the water butt.

Î Separate the high pressure hose from the

high pressure connection of the appliance.

Î Appliance ventilation.

Let the appliance run when the high-pres-

sure hose is not connected and run it until

the water which discharges from the high-

pressure outlet is free of bubbles. Switch off

appliance and reconnect high-pressure

hose.

Caution

Dry runs lasting longer than two minutes lead to

damages to the high pressure pump. If the appli-

ance does not build up pressure within two min-

utes, switch it off and proceed as instructed in

the Chapter "Troubleshooting".

Caution

The appliance is delivered without engine oil.

Please fill in engine oil before using the appli-

ance for the first time.

Î Fill up the fuel tank and check the oil level.

See Operating Instructions of motor.

Î Connect the high pressure hose to the high

pressure connection of the appliance.

Î Push the spray lance into the trigger gun and

fasten it by turning it through 90°.

Î Completely open the water tap.

Î Start the motor.

See Operating Instructions of motor.

Before Startup

Water supply

Water supply from mains

Drawing in water from open reservoirs

Start up

14 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher g 4 10 m Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info