Bedienungsanleitung Karcher HD 7-17 M Plus (Seite 16 von 208) (Alle Sprachen)

725230

Zoom out

Zoom in

Vorherige Seite

1/208

Nächste Seite

16 English

Suck water from the container

1. Screw the suction hose (order number 4.440-207.0)

and filter (order number 4.730-012.0) onto the water

connection.

2. Vent the device.

Vent the device

1. Unscrew the nozzle from the spray lance.

2. Allow the device to run until the escaping water is

free of air bubbles.

3. In the case of venting problems, allow the device to

run for 10 seconds and then switch it off. Repeat the

procedure several times.

4. Switch off the device.

5. Screw the nozzle back in place.

Only with HD...M PU: High-pressure installation

The applicable national regulations for permanently in-

stalled high-pressure cleaning systems must be ob-

served.

1. Connect the device to the permanently installed pip-

ing using a high-pressure hose line.

2. Route the permanently installed piping with as few

changes in direction as possible.

3. Route the piping using padded loose and fixed clips

to compensate for pressure and thermal expansion.

4. Minimum line cross-sections:

a Pipelines: Nominal width DN 15 (1/2”).

b Hose lines: Nominal width DN 6.

Operation

 DANGER

Risk of injury from the high-pressure water jet

Never fasten the trigger and safety lever in the actuated

position.

Do not use the high-pressure gun when the safety lever

is damaged.

Push the safety latch of the high-pressure gun forwards

every time before starting work with the device.

Opening/closing the high-pressure gun

1. Opening the high-pressure gun: Actuate the safety

lever and trigger.

2. Closing the high-pressure gun: Release the safety

lever and trigger.

High-pressure operation

The device can be operated in a standing or lying posi-

tion.

Note

The device is equipped with a pressure switch. The mo-

tor only starts up when the high-pressure gun is open.

1. Device with a hose reel: Completely unroll the high-

pressure hose from the hose reel.

2. Set the power switch to "I".

3. Unlock the high-pressure gun by pushing the safety

latch of the high-pressure gun to the rear.

4. Open the high-pressure gun.

5. For devices with pressure and volume regulator: Set

the working pressure by turning the pressure and

volume regulator.

Operation with detergent

Note

A cup foam lance (optional)is needed for operating with

detergent.

몇 WARNING

Health risk through incorrect handling of deter-

gents

Observe the safety instructions on the detergent.

ATTENTION

Unsuitable detergents can damage the device and

the object to be cleaned.

Use only detergents approved by KÄRCHER.

Observe the dosing recommendations and notes pro-

vided with the detergent.

Use detergents sparingly to help conserve the environ-

ment.

KÄRCHER detergents ensure fault-free operation. Ask

us for a consultation, request our catalogue or our de-

tergent information sheets.

Figure C

1 Foam nozzle

2 Container

3 Blender

Detergent mixing: 3=high, 2=medium, 1=low

4 Suction hose

5 Spray lance

1. Unscrew the container.

2. Plug the desired blender into the suction hose.

3. Fill the detergent into the container.

4. Screw the container onto the foam nozzle.

5. Remove the nozzle from the spray lance.

6. Connect the foam nozzle to the high-pressure gun

and hand-tighten.

7. Start up the high-pressure cleaner.

Recommended cleaning method

1. Spray the detergent sparingly on the dry surface and

let it work for a while (do not let it dry).

2. Rinse off the loosened dirt with the high-pressure

jet.

Rinsing out the foam lance

The foam lance must be flushed after use to prevent the

formation of detergent deposits.

1. Unscrew the container.

2. Pour the remaining detergent back into the original

packaging.

3. Fill the container with clear water.

4. Screw the container onto the foam nozzle.

5. Operate the foam nozzle for approx. 1 minute to

flush the detergent residue.

6. Empty the container.

Interrupting operation

1. Close the high-pressure gun, the device will switch

off.

2. Lock the high-pressure gun by pushing the safety

latch of the high-pressure gun to the front.

Note

The water pressure in the high-pressure hose is re-

duced by approx. 70% when the device is switched off.

This reduces the actuating force of the high-pressure

gun and extends the service life of the device.

Continuing operation

1. Unlock the high-pressure gun by pushing the safety

latch to the rear.

2. Open the high-pressure gun, the device will switch

on again.

Finishing operation

1. Close off the water inlet.

2. Open the high-pressure gun.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HD 7-17 M Plus Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info