Bedienungsanleitung Karcher HD 7-17 MX (Seite 16 von 204) (Alle Sprachen)

725215

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

16 English

2. Wind the mains cable onto the cable clips.

HD...M:

Wind on the high-pressure hose, hang it over

the hose storage compartment and secure with the

rubber band.

HD...MX:

Wind the high-pressure hose

onto the hose reel and fold over the crank handle.

4. Press the push handle lock and slide in the push

handle.

Frost protection

ATTENTION

Frost destroys the device if it is not completely

drained of water.

Store the device in a frost-free location.

If frost-free storage is not possible:

1. Drain the water.

2. Pump commonly available anti-freeze through the

device.

3. Allow the device for run for a maximum of 1 minute

until the pump and lines are empty.

Note

Use commonly available, Glycol-based vehicle anti-

freeze. Observe the handling instructions of the anti-

freeze manufacturer.

Transport

몇 CAUTION

Risk of injury, risk of damage

Be aware of the weight of the device during transport.

ATTENTION

Risk of damage

Protect the trigger of the high-pressure gun from damage.

1. When transporting in vehicles, secure the device

against slipping and tipping over according to the

applicable guidelines.

2. Pull the device behind you via the push handle for

transporting over longer distances (not with HD...M

St).

3. Pull the device step by step when ascending stairs.

The skids protect the casing from damage (not with

HD...M St).

Only with HD...M, HD...MX: Transport retainer

for surface cleaner

1. Plug the connection nozzle of the surface cleaned

onto the transport bracket on the high-pressure

cleaner.

2. Screw on the union nut by approximately 1 turn.

Storage

몇 CAUTION

Risk of injury, risk of damage.

Be aware of the weight of the device during storage.

1. Store the device indoors only.

Care and service

 DANGER

Risk of injury due to inadvertently starting up de-

vice and also due to electric shock.

Switch off the device immediately and unplug the mains

plug before performing work.

Safety inspection/maintenance contract

You can agree on regular safety inspections or close a

maintenance contract with your dealer. Please seek ad-

vice on this.

Each time before use

1. Check the power cable for damage and have a dam-

aged cable replaced immediately by the authorised

Customer Service or a qualified electrician.

2. Check the high-pressure hose for damage and re-

place a damaged high-pressure hose immediately.

3. Check the device for leaks. 3 drops of water per min-

ute are permissible. Contact Customer Service in

the case of more serious leaks.

Weekly

1. Clean the sieve in the water connection.

Clean the sieve in the water connection

1. Unscrew the union nut.

2. Pull out the hose union with sieve.

3. Externally clean and rinse the sieve.

Note: Align the hex-head of the hose union for con-

nection to the device.

4. Fit the hose union with sieve.

5. Tighten the union nut.

Every 500 operating hours, at least annually

1. Have the device maintained by Customer Service.

2. Changing oil.

Changing oil

Note

See the "Technical data" section for the oil volume and

type

1. Unscrew the 4 screws.

2. Remove the cover.

Figure D

3. Pivot the oil drain hose downwards over an oil catch

pan.

4. Pull the plug out of the oil drain hose.

5. Remove the cap.

6. Remove the foam from the oil tank.

7. Wait until the oil has drained completely.

Figure E

8. Insert the plug into the oil drain hose.

9. Pivot the oil drain hose upwards and latch in place.

10. Fill with the measured correct quantity of oil.

11. Insert the foam into the oil tank.

12. Fit the cap and press firmly in place.

Figure F

Troubleshooting guide

 DANGER

Risk of injury due to inadvertently starting up de-

vice and also due to electric shock.

Switch off the device immediately and unplug the mains

plug before performing work.

Have electrical components checked and repaired by

the authorised Customer Service.

In case of any malfunctions not mentioned in this chapter,

contact the authorised Customer Service when in doubt or

when you have been explicitly advised to do so.

Device does not start

 Check the power cable for damage.

 Check the mains voltage.

 If the device overheats:

a Set the power switch to "0".

b Allow the device to cool for at least 15 minutes.

c Set the power switch to "1".

 Contact Customer Service in the case of electrical

faults.

Device does not reach required pressure

 Check the size of the nozzle and compare with the

required size specified in the "Technical data" sec-

tion.

 Vent the device, see section "Venting the device".

 Clean the sieve in the water connection.

 Check the water supply volume and compare with

the required volume specified in the "Technical data"

section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HD 7-17 MX Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info