Bedienungsanleitung Karcher HDC 20-16 H (Seite 28 von 384) (Alle Sprachen)

726300

Zoom out

Zoom in

Vorherige Seite

1/384

Nächste Seite

- 12

– Before installing, please check the

load-bearing capacity of the wall. Use

suitable anchor plugs and screws for

concrete walls, hollow component

walls, brick walls and gas concrete

walls - for e.g. injection anchors (see

packaging for drilling template).

– The appliance should not be directly at-

tached to the network of water and high

pressure pipes. It is mandatory to install

the connecting hoses.

– A shut-off tap must be installed be-

tween the main water supply and the

connecting hose.

All national laws and regulations about in-

stallation of electrical appliances must also

be followed when installing high pressure

lines.

– The pressure loss in the pipe connec-

tions must lie below 1.5 MPa.

– The completed pipeline must be tested

with 16 MPa (HDC 20/8) bzw. 32 MPa

(HDC 20/16).

– The insulation of the pipes must be re-

sistant to temperatures until 100 °C.

ATTENTION

Risk of damage to the plant if water supply

is not of suitable quality.

Note: Impurities in the inlet water can dam-

age the unit. Kärcher recommends a water

filter with a mesh width of < 80 μm.

Quality requirements for tap water:

* Test volume 1litre, Settling time 30 min-

utes

** decalcification measures are necessary

if the values are higher

The water inlet is to be connected to the

main water supply using a water hose.

– The water supply must have a minimum

output of 2,000 l/h at minimum 0.15

MPa.

– Appliances without prepressure pump:

The water temperature must lie below

60 °C.

– Machines with prepressure pump: The

water temperature must lie below 85

°C.

Note: Operating procedures create short

term power sinkings. During unfavorable

net conditions other devices might be dis-

turbed.

ATTENTION

The highest allowed net impedance at the

electrical connection point (refer to techni-

cal data) is not to be exceeded. In case of

confusion regarding the power impedance

present on your connection, please contact

your utilities provider.

– For connection values, see technical

data and type plate.

– The electrical connections must be

done by an electrician according to IEC

60364-1.

– Current-carrying parts, cables and ap-

pliances in the working area must be in-

stalled in a defectless state and must be

protected against water sprays.

DANGER

To avoid accidents due to electrical faults

we recommend the use of sockets with a

line-side current-limiting circuit breaker

(max. 30 mA nominal tripping current).

Installing the plant

Only for authorised techni-

cians!

Wall mount

Installing the high pressure

connections

Water supply

pH value 6,5...9,5

electrical conductivity < 2000 μS/cm

removable materials < 0,5 mg/l *

filterable materials (grain

size below 0.025 mm)

< 20 mg/l

Hydrocarbons < 20 mg/l

Chloride < 300 mg/l

Calcium < 85 mg/l **

Total hardness < 9 °dH **

Iron < 0,5 mg/l

Manganese < 0,05 mg/l

Copper < 0,02 mg/l

free of bad odours

Electrical connection

28 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDC 20-16 H Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info