Bedienungsanleitung Karcher HDC 90-10 H Advanced (Seite 29 von 376) (Alle Sprachen)

726294

Zoom out

Zoom in

Vorherige Seite

1/376

Nächste Seite

- 13

ATTENTION

Always keep the installation site of the sys-

tem well ventilated to protect the machine

against over-heating.

– The appliance should not be directly at-

tached to the network of water and high

pressure pipes. It is mandatory to install

the connecting hoses.

– A shut-off tap must be installed be-

tween the main water supply and the

connecting hose.

For installation, please follow the specifica-

tions of the VDMA sheet 24416 "High pres-

sure cleaners; fixed high pressure cleaning

systems; concepts, requirements, installa-

tion, testing" (the German version can be

procured from Beuth Verlag, Cologne,

www.beuth.de).

– The pressure loss in the pipe connec-

tions must lie below 1.5 MPa.

– The completed pipe connections must

be checked using 32 MPa.

– The insulation of the pipes must be re-

sistant to temperatures until 100 °C.

ATTENTION

Risk of damage to the plant if water supply

is not of suitable quality.

Note: Impurities in the inlet water can dam-

age the unit. Kärcher recommends a water

filter with a mesh width of < 80 μm.

Quality requirements for tap water:

* Test volume 1litre, Settling time 30 min-

utes

** decalcification measures are necessary

if the values are higher

The water inlet is to be connected to the

main water supply using a water hose.

– The water supply must have a minimum

output of 6,000 l/h for HDC 60/10,

9,000 l/h for HDC 90/10, 12,000 l/h for

HDC 120/10 at minimum 0.15 MPa

(HDC 60/10, HDC 90/10) or at minimum

0.2 MPa (HDC 120/10).

– Appliances without prepressure pump:

The water temperature must lie below

60 °C.

– Machines with prepressure pump: The

water temperature must lie below 85

°C.

Note: Operating procedures create short

term power sinkings. During unfavorable

net conditions other devices might be dis-

turbed.

– For connection values, see technical

data and type plate.

– The electrical connections must be

done by an electrician according to IEC

60364-1.

– Current-carrying parts, cables and ap-

pliances in the working area must be in-

stalled in a defectless state and must be

protected against water sprays.

– HDC 60/10 (H): This device complies

with IEC 61000-3-12 under the condi-

tion that the short-circuit power Ssc at

the connecting point between the cus-

tomer system and the public mains is

greater than or equal to 10400 (11000)

kVA. It is within the responsibility of the

electrician or the user of the unit to en-

sure - if necessary after consulting the

mains operating company - that the de-

vice is only connected to a point of an

Ssc value greater than or equal to

10400 (11000) kVA.

DANGER

To avoid accidents due to electrical faults

we recommend the use of sockets with a

line-side current-limiting circuit breaker

(max. 30 mA nominal tripping current).

We hereby declare that the machine de-

scribed below complies with the relevant

basic safety and health requirements of the

EU Directives, both in its basic design and

construction as well as in the version put

into circulation by us. This declaration shall

cease to be valid if the machine is modified

without our prior approval.

5.957-926

The signatories act on behalf of and with

the authority of the company management.

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Straße 28-40

71364 Winnenden (Germany)

Tel.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2018/10/01

The warranty terms published by our com-

petent sales company are applicable in

each country. We will repair potential fail-

ures of the appliance within the warranty

period free of charge, provided that such

failure is caused by faulty material or de-

fects in fabrication.

Installing the plant

Only for authorised techni-

cians!

Assembly

Installing the high pressure

connections

Water supply

pH value 6,5...9,5

electrical conductivity < 2000 μS/cm

removable materials < 0.5 mg/l *

filterable materials (grain

size below 0.025 mm)

< 20 mg/l

Hydrocarbons < 20 mg/l

Chloride < 300 mg/l

Calcium < 85 mg/l **

Total hardness < 15 °dH **

Iron < 0.5 mg/l

Manganese < 0.05 mg/l

Copper < 0.02 mg/l

free of bad odours

Electrical connection

EU Declaration of Conformity

Product: High pressure cleaner

Type: 2.509-xxx

Relevant EU Directives

2006/42/EC (+2009/127/EC)

2014/30/EU

Applied harmonized standards

EN 60335–1

EN 60335–2–79

EN 55014–1: 2006+A1: 2009+A2: 2011

EN 55014–2: 2015

EN 61000-6-4: 2007

EN 61000–6–2: 2005

EN 61000–3–11: 2000

EN 61000–3–12: 2011

Warranty

Chairman of the Board of Management

Director Regulatory Affairs & Certiﬁcation

29EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDC 90-10 H Advanced Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info