Bedienungsanleitung Karcher HDS 1195 SX Eco (Seite 29 von 484) (Alle Sprachen)

538578

Zoom out

Zoom in

Vorherige Seite

1/484

Nächste Seite

– 6

– Continuous operation is worse than an

operation interrupted by pauses.

In case of regular, long-term operation of

the device and in case of repeated occur-

rence of the symptoms (e.g. cold, numb fin-

gers) please consult a physician.

ƽ Danger

Switch the appliance off prior to replacing

nozzel and activate hand spray gun until

device is pressureless.

 Set the appliance switch to "I".

Indicator lamp for operational readiness

lights up.

Note: The temperature regulator must be

at "0" position because otherwise the burn-

er will switch off.

Note: If the control lamps fuel, liquid soften-

er or motor light up, please switch the appli-

ance off immediately and fix the error, see

"Help with errors".

The device starts briefly and turns off, as

soon as the working pressure is reached.

Figure 8

 Release the hand spray gun (A).

When activating the hand spray gun the de-

vice switches back on.

Note:If no water comes out of the high

pressure nozzle, vent pump. Refer to "Help

with malfunctions - appliance is not building

up pressure".

 Set temperature regulator to desired

temperature.

30 °C to 90 °C

– Clean with hot water.

100 °C to 150 °C

– Clean using steam.

 Replace the high-pressure nozzle with

steam nozzle (refer "Using steam").

Figure 9

 Turn the regulation spindle in a clock-

wise direction: Increase working pres-

sure (MAX).

 Turn the regulation spindle in an anti-

clockwise direction: Reduce working

pressure (MIN).

 Set thermostat to max. 98 °C.

 Set the operating pressure on the appli-

ance to the maximum value.

Figure 8

 Set working pressure and flow rate

through turning (directly) at the pres-

sure- and amount regulation (B) of the

handgun (+/-).

ƽ Danger

When adjusting the pressure/quantity regu-

lation, make sure that the screw connection

of the spray lance does not become loose.

Note: For long term work with low pres-

sure, set pressure at device.

– For considerate treatment of the envi-

ronment use detergent economically.

– The detergent must be suitable for the

surface to be cleaned.

 With support of the detergent dose

valve set detergent concentration as

determined by the manufacturer.

Note: Recommended values at the control

panel at maximum working pressure.

 Set pressure/temperature and deter-

gent concentration according to the sur-

face to be cleaned.

Note: To prevent damage due to too much

pressure, always position high pressure ray

first from a greater distance towards object

to be cleaned.

Replace the nozzle

Turning on the Appliance

Adjust cleaning temperature

Set working pressure and flow rate

Appliance setting

Servo pressure regulation

Operation with detergent

Cleaning

29EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDS 1195 SX Eco Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Karcher HDS 1195 SX Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info