Bedienungsanleitung Karcher HDS 1195 (Seite 12 von 17) (Englisch)

538469

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

English HDS Super, HDS 695 S, HDS 745, HDS 895 S, HDS 995, HDS 1195, HDS 1295 12

Unit does not run

(HDS 745, HDS 695 S, HDS 895 S, HDS 995,

HDS 1195, HDS 1295, HDS Super)

No mains voltage

– Check mains connection/power cord

Unit does not build up pressure

(HDS 745, HDS 695 S, HDS 895 S, HDS 995,

HDS 1195, HDS 1295, HDS Super)

Air in system

– Bleed pump:

* Set the cleaning agent metering valve

(item 31) to "0"

* While the handgun is open switch the unit on

and off several times with the unit switch.

* With handgun open, open and close regulator

(Figure 9).

* Venting is accelerated by removing the high-

pressure hose from the high-pressure

connection.

– Fill up cleaning-agent tank if empty.

– Check connections and lines

Pressure set to MIN

– Set pressure to MAX

Strainer in water connection dirty

– Clean strainer

Insufficient water supply

– Check water supply volume

(refer to technical data)

–

Unit leaking, water dripping out at bottom

(HDS 745, HDS 695 S, HDS 895 S, HDS 995,

HDS 1195, HDS 1295, HDS Super)

Pump leaking

– 3 droplets/min are permitted.

– In the event of a major leak, have unit

checked by After-Sales Service.

Unit constantly switched on and off with

handgun closed

(HDS 745, HDS 695 S, HDS 895 S, HDS 995,

HDS 1195, HDS 1295, HDS Super)

Leak in high-pressure system

– Check high-pressure system and connections

for leaks

Unit does not draw in cleaning agent

(HDS 745, HDS 695 S, HDS 895 S, HDS 995,

HDS 1195, HDS 1295, HDS Super)

Operate the unit with an opened cleaning agent

metering valve and a shut off water inlet until

the float tank is suctioned empty and the

pressure drops to "0".

– Now reopen the water inlet.

If the pump still does not suction up cleaning

agent the reasons can be as follows:

Filter in cleaning-agent suction hose dirty

– Clean filter

Non-return valve gummed up

– Pull the cleaning agent hose off and detach

the non-return valve with a blunt object, see

Figure 15.

Burner not ignited

(HDS 745, HDS 695 S, HDS 895 S, HDS 995,

HDS 1195, HDS 1295, HDS Super)

Fuel tank empty

– Fill up

Lack of water

– Check water connection, check supply lines,

clean low water protection.

Fuel filter dirty

– Replace fuel filter.

Incorrect direction of rotation. If direction of

rotation is correct, powerful jet of air will be felt

at exhaust-gas opening of burner.

– Check direction of rotation. If

necessary change the poles at the unit plug.

See figure 16.

No ignition spark

– Have unit checked by After-Sales Service if

no ignition spark is visible through inspection

glass during operation.

Set temperature not attained when working

with hot water

(HDS 745, HDS 695 S, HDS 895 S, HDS 995,

HDS 1195, HDS 1295, HDS Super)

Excessive operating pressure/flow rate

– Reduce operating pressure/flow rate by way

of regulator (Figure 9)

Soot deposits on heating coil

– Have After-Sales Service remove soot

deposits from unit

If the problem cannot be resolved the unit

must be checked by after sales service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDS 1195 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Karcher HDS 1195

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info