Bedienungsanleitung Karcher HDS 13-20 De Tr1 (Seite 33 von 512) (Alle Sprachen)

726238

Zoom out

Zoom in

Vorherige Seite

1/512

Nächste Seite

- 13

DANGER

Before carrying out any tasks on the ma-

chine, switch the key switch off and remove

it.

DANGER

Risk of injury on account of electric shock!

Do not place metallic objects on the alter-

nator or starter.

DANGER

Risk of explosion! Do not put tools or similar

on the battery, i.e. on the terminal poles

and cell connectors.

Allow device to cool down.

Disassemble the water inlet filter and

take out the filter inlay.

Clean the filter with clean water or com-

pressed air.

Reinstall in reverse sequence.

Unpressurize the appliance.

Disassemble the pump prefilter and

take out the filter inlay.

Clean the filter with clean water or com-

pressed air.

Reinstall in reverse sequence.

Unscrew the screw cap of the detergent

suction hose.

Take out detergent suck hose.

Clean filter in water and reinstall.

Note: The filling quantity between the MIN

and MAX markings on the oil dipstick is 1.6

litres.

Remove the oil dip, wipe it and reinsert

it.

Remove the oil dip one more time and

check the oil level.

The oil level is correct if it is within the

markings on the oil dip.

If the oil level is below the mark, open

the filler neck lid and add fresh motor

oil.

Wait five minutes, until the oil has col-

lected in the oil pan.

Check the oil level as described above.

Repeat this procedure as often as nec-

essary until the oil level is between the

markings on the oil dip.

After the check, insert the oil dip and

close the lid of the filler neck.

Note: Air pockets must be able to leak out.

For oil type refer to technical specifica-

tions

Check the oil level at the oil-level gauge

of the intermediate gear.

The oil level is correct if it is in the mid-

dle of the oil-level gauge.

If the oil level is below the middle of the

oil-level gauge, open the lid of the filling

hole and fill in fresh transmission oil.

Close filling hole.

Note: Air pockets must be able to leak out.

For oil type refer to technical specifica-

tions

HDS 9/50, HDS 13/35 only:

Check the oil level at the oil tank of the

high-pressure pump.

The oil level is correct if it is between the

MIN and MAX marking.

If the oil level is below the MIN marking,

open the lid of the oil container and fill in

fresh oil.

Close the lid of the oil container.

Note: Air pockets must be able to leak out.

For oil type refer to technical specifica-

tions

HDS 13/20, HDS 17/20 only:

Remove the oil dipstick, wipe it and in-

sert it again.

Remove the oil dipstick again and

check the oil level.

The oil level is correct if it is within the

markings on the oil dip.

If the oil level is below the mark on the

oil dipstick, fill up with fresh oil.

Twist in the oil dipstick.

Note: Air pockets must be able to leak out.

For oil type refer to technical specifica-

tions

몇CAUTION

Observe the brand of antifreeze used. The

mixture can cause a chemical reaction and

hazardous substances can be generated.

Do not mix different antifreeze types.

몇WARNING

The motor can overheat if there is a lack of

coolant. Turn the motor off immediately and

let it cool down.

몇WARNING

If the motor is so overheated, that water va-

pors escape, immediately turn the motor off

and keep a safety distance to the motor un-

til the pressure has decreased.

몇WARNING

Scalding danger! Never open the lid on the

expansion tank of the motor cooling water

with operating temperature. The container

is under pressure.

Open the lid on the equalisation con-

tainer of the motor coolant, fill in fresh

clean water and the required antifreeze.

Note: For rough cleaning of the air filter,

proceed as follows: Hold the catch pan un-

der the dirt outlet and operate the dirt outlet.

Note: Heavily soiled or defective filter in-

lays must always be replaced.

Loosen the spring tension bracket, re-

move the cover and eliminate the dust

deposits.

Take out the filter inlay.

Blow out the filter insert with com-

pressed air (max. 2 bar) from the inside.

Clean the inside of the air filter housing

with a cloth.

Insert the filter inlay into the air filter

casing.

Attach the cover and fasten it by means

of the spring tension bracket.

Maintenance Works

Clean the water inlet filter

Clean the pump prefilter

Clean filter at the detergent suck hose

Check the oil level on the motor and add

motor oil

Checking the oil level on the

intermediate gear and refilling

transmission oil

Check the oil level on the oil tank of the

high-pressure pump, then top up the oil

if necessary

Check the oil level on the oil dipstick of

the high-pressure pump, then top up the

oil if necessary

Check the coolant and refill

Cleaning/replacing the air filter

33EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDS 13-20 De Tr1 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info