Bedienungsanleitung Karcher HDS 9-17-4 C Classic (Seite 24 von 360) (Alle Sprachen)

726216

Zoom out

Zoom in

Vorherige Seite

1/360

Nächste Seite

– 5

For connection values refer to technical

specifications

 Attach supply hose (minimum length

7.5 m, minimum diameter 3/4“) to the

water supply set by means of a hose

clamp.

 Connect the supply hose to the water

connection point of the machine and at

the water supply point (for e.g. a tap).

Note: The supply hose and the hose clamp

are not included in the scope of delivery.

If you want to suck in water from an exter-

nal vessel, the following modification is

necessary:

 Remove the system care bottle.

Figure 6

 Remove the two screws on the burner

casing.

Figure 7

 Unscrew the back wall and remove it.

The nozzle of the system care reservoir

will remain in the back wall.

Figure 8

 Remove water connection from the fine

filter.

 Unscrew the fine filter from the pump

head.

 Remove the system care reservoir.

Figure 9

 Unscrew the top supply hose to the

swimmer container.

 Connect the top supply hose at pump

head.

 Replug the rinse line of the detergent

dosing valve to blind plugs.

 Connect suction hose (minimum diame-

ter 3/4“) with filter (accessory) to the

water connection point.

– Max. suck height: 0.5 m

Until the pump sucked in water, you should:

 Set the pressure/quantity regulation at

the pump unit to maximum quantity.

 Close the dosing valve for the deter-

gent.

 DANGER

Risk of personal injury or damage! Never

suck in water from a drinking water contain-

er. Never suck in liquids which contain sol-

vents like lacquer thinner, petrol, oil or unfil-

tered water. The sealings within the device

are not solvent resistant. The spray mist of

solvents is highly inflammable, explosive

and poisonous.

 Assembly in reverse order.

Note: Ensure that the solenoid valve cable

on the reservoir of the system care is not

pinched.

Figure 10

Note: After placing the back wall, reach into

the chute of the system care and press the

nozzle onto the system care reservoir.

– For connection values, see technical

data and type plate.

– The electrical connections must be

done by an electrician according to IEC

60364-1.

 DANGER

Risk of injury on account of electric shock!

– Unsuitable electrical extension cables

can be hazardous. Only use electrical

extension cables outdoors which have

been approved and labelled for this pur-

pose and have an adequate cable

cross-section.

– Always unwind extension lines com-

pletely.

– The plug and coupling of the extension

cable used must be watertight.

 DANGER

Danger of explosion! Do not spray flamma-

ble liquids.

 DANGER

Risk of injury! Never use the appliance

without the spray lance attached. Check

and ensure proper fitting of the spray lance

prior to each use. The screw connection of

the spray lance must be finger-tight.

Water connection

Suck in water from vessel

Power connection

Operation

24 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDS 9-17-4 C Classic Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info