Bedienungsanleitung Karcher HDS 9-17-4 C-CX (Seite 20 von 276) (Alle Sprachen)

726212

Zoom out

Zoom in

Vorherige Seite

1/276

Nächste Seite

– 4

If you want to suck in water from an external vessel, the

following modification is necessary:

 Remove the system care bottle.

Figure 8

 Remove the two screws on the burner casing.

Figure 9

 Unscrew the back wall and remove it. The nozzle of

the system care reservoir will remain in the back

wall.

Figure 10

 Remove water connection from the fine filter.

 Unscrew the fine filter from the pump head.

 Remove the system care reservoir.

Figure 11

 Unscrew the top supply hose to the swimmer con-

tainer.

 Connect the top supply hose at pump head.

 Replug the rinse line of the detergent dosing valve

to blind plugs.

 Connect suction hose (minimum diameter 3/4“)

with filter (accessory) to the water connection point.

– Max. suck height: 0.5 m

Until the pump sucked in water, you should:

 Set the pressure/quantity regulation at the pump

unit to maximum quantity.

 Close the dosing valve for the detergent.

 DANGER

Risk of personal injury or damage! Never suck in water

from a drinking water container. Never suck in liquids

which contain solvents like lacquer thinner, petrol, oil or

unfiltered water. The sealings within the device are not

solvent resistant. The spray mist of solvents is highly in-

flammable, explosive and poisonous.

 Assembly in reverse order.

Note: Ensure that the solenoid valve cable on the res-

ervoir of the system care is not pinched.

Figure 12

Note: After placing the back wall, reach into the chute

of the system care and press the nozzle onto the system

care reservoir.

– For connection values, see technical data and type

plate.

– The electrical connections must be done by an

electrician according to IEC 60364-1.

 DANGER

Risk of injury on account of electric shock!

– Unsuitable electrical extension cables can be haz-

ardous. Only use electrical extension cables out-

doors which have been approved and labelled for

this purpose and have an adequate cable cross-

section.

– Always unwind extension lines completely.

– The plug and coupling of the extension cable used

must be watertight.

ATTENTION

The highest allowed net impedance at the electrical

connection point (refer to technical data) is not to be ex-

ceeded. In case of confusion regarding the power im-

pedance present on your connection, please contact

your utilities provider.

 DANGER

Danger of explosion! Do not spray flammable liquids.

 DANGER

Risk of injury! Never use the appliance without the spray

lance attached. Check and ensure proper fitting of the

spray lance prior to each use. The screw connection of

the spray lance must be finger-tight.

 DANGER

Risk of injury! Hold the hand spray gun and the spray

pipe firmly with both hands.

 DANGER

Risk of injury! The trigger and safety lever may not be

locked during the operation.

 DANGER

Risk of injury! Contact Customer Service if the safety le-

ver is damaged.

ATTENTION

Risk of damage! Never operate device with an empty

fuel tank. The fuel pump will otherwise be destroyed.

 To open the trigger gun: Actuate the safety lever

and trigger.

 To close the hand spray gun: Release the safety le-

ver and trigger.

 DANGER

Risk of injury! Switch the appliance off prior to replacing

nozzle and activate hand spray gun until device is pres-

sureless.

 Secure the trigger gun. To do so, push the safety

catch towards the front.

 Replacing the nozzle.

 Set appliance switch to desired operating mode.

Indicator lamp for operational readiness lights up.

The device starts briefly and turns off, as soon as the

working pressure is reached.

Note: If the control lamp "rotation direction" lights up,

please switch the appliance off immediately and fix the

error, see "Help with malfunctions".

 Release the trigger gun. To do so, push the safety

catch towards the back.

When activating the hand spray gun the device switch-

es back on.

Note: If no water comes out of the high pressure nozzle,

vent pump. Refer to "Help with malfunctions - appliance

is not building up pressure".

 Set device switch to desired temperature.

30 °C to 98 °C

– Clean with hot water.

100 °C to 150 °C

– Clean using steam.



 In steam operation (> 100°C), use the steam noz-

zle available as an accessory (see “Steam opera-

tion”).

Suck in water from vessel

Power connection

Operation

Opening/closing the trigger gun

Replace the nozzle

Turning on the Appliance

Adjust cleaning temperature

20 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher HDS 9-17-4 C-CX Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info