Bedienungsanleitung Karcher K 4 Premium (Seite 19 von 294) (Alle Sprachen)

576553

Zoom out

Zoom in

Vorherige Seite

1/294

Nächste Seite

– 9

You will need the 2 included screws as well

as a Phillips screwdriver PH 2.

Illustration

 Insert both detergent hoses onto the

hose fittings.

 Install the dosage regulator and con-

nect using 2 screws.

Note: During installation you must

make sure that the tongues of the dos-

age regulator match up with the intend-

ed recesses in the casing.

Illustration

 Slide the free end of the coiled high

pressure hose through the recesses on

the dosage regulator.

 Insert the hose drum into the intakes on

the transport handle.

 Insert the axle of the hand crank into the

guides.

 Install the fixating plate and secure it

using 2 screws.

 Press the connecting fitting from the

short high pressure hose into the brass

intake, secure with clamps.

Note: Make sure the connection nipple

is aligned correctly.

Illustration

 Push the high pressure hose into the

trigger gun until it locks audibly.

Note: Make sure the connection nipple

is aligned correctly.

Check the secure connection by pulling

on the high pressure hose.

Caution

Impurities in the water can damage the

high-pressure pump and the accessories.

For protection, the use of the KÄRCHER

water filter (optional accessory, order no.

4.730-059) is recommended.

For connection values, see type plate/tech-

nical data.

Observe regulations of water supplier.

ṇ Warning

According to applicable regulations, the ap-

pliance must never be used on the drinking

water net without a system separator. A

suitable system separator by KÄRCHER or

alternatively a system separator according

to EN 12729 type BA must be used.

Water that has flown through a system sep-

arator is no longer classified as drinking

water.

Caution

Always connect the system separator to

the water supply, never directly to the appli-

ance!

Illustration

 Screw the coupling element to the wa-

ter connection on the appliance.

This high-pressure cleaner is suited to work

with the KÄRCHER suction hose with back-

flow valve (Optional accessory, order no.

4.440-238) to draw in surface water, e.g.

from water butts or ponds (see specifica-

tions for max. suction height).

 Fill the suction hose with water.

 Screw the suction hose into the water

connection of the appliance and insert it

into the water source (e.g. rainwater

drum).

Caution

Dry running of more than 2 minutes leads to

damage of the high-pressure pump. If the

appliance does not build up pressure within

2 minutes, switch the appliance off and pro-

ceed in accordance with the instructions in

Chapter "Troubleshooting".

Illustration

 Unwind the high pressure hose com-

pletely from the hose drum. Hold on to

the transport handle during this proce-

dure.

Note: If the hand crank is in its secured

position, fold it up first.

 Attach the water supply hose to the

coupling on the water connection.

Install the dosage regulator for

detergent

Install the high pressure hose drum

Connect the high pressure hose to the

trigger gun

Water supply

Water supply from mains

Drawing in water from open reservoirs

Start up

19EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher K 4 Premium Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info