Bedienungsanleitung Karcher K 4.20 M + T 200 (Seite 11 von 176) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78138

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

English 11

When unpacking the product, make sure that

no accessories are missing and that none of

the package contents have been damaged. If

you detect any transport damages please

contact your dealer.

Illustrations on Page 2

1 Appliance switch "0/OFF“/ „I/ON“

2 Mains cable with mains plug

3 High pressure connection

4 High pressure hose

5 Hand blowing gun

6 Lock trigger gun

7 Sieve in the water connection

8 Water connection

9 Coupling element for water connection

10 Detergent suction hose (with filter)

11 Storage for trigger gun

12 Transport handle

13 Spray lance with pressure regulation

(Vario Power)

14 Spray lance with dirt blaster

Special accessories expand the possibilities

of using your appliance. Please contact your

Kärcher dealer for further information.

Mount loose parts delivered with appliance

prior to start-up.

Illustration

Î Pull out the clamp for the high-pressure

hose from the trigger gun (e.g. a small

screwdriver).

Î Connect high pressure hose to trigger

gun.

Î Push the clamp in until it locks. Check the

secure connection by pulling on the high-

pressure hose.

Illustration

Î Insert the transport handle and screw in.

Illustration

Î Insert holder for trigger gun.

According to the applicable regula-

tions, the appliance must never be

used on the drinking water net with-

out a system separator. Use a suita-

ble system separator manufactured by

Kärcher; or, as an alternative, a system sepa-

rator as per EN 12729 Type BA.

Note: Impurities in the water can damage the

high-pressure pump and the accessories. For

protection, the use of the Kärcher water filter

(optional accessory, order no. 4.730-059) is

recommended.

Observe regulations of water supplier.

For connection values, see type plate/techni-

cal data.

Î Use a fibre-reinforced water hose (not in-

cluded) with a standard coupling. (Mini-

mum diameter 1/2 inch (13 mm),

minimum length 7.5 m).

Illustration

Î Screw the coupling unit (supplied) to the

water connection on the appliance.

Î Push the water supply hose onto the cou-

pling unit, then connect it to the water sup-

ply.

This high-pressure cleaner is suited to work

with the Kärcher suction hose with backflow

valve (Optional accessory, order no. 4.440-

238) to draw in surface water, e.g. from water

butts or ponds (see specifications for max.

suction height).

Î Fill the Kärcher suction hose with back-

flow valve with water, screw to water sup-

ply and hang into he water butt.

Î Separate the high pressure hose from the

high pressure connection point of the ap-

pliance.

Î Switch the appliance on "I/ON" and oper-

ate until the water exits the high-pressure

connection without bubbles.

Î Turn off the appliance "0/OFF".

Operation

Description of the Appliance

Special accessories

Before Startup

Water supply

Water supply from mains

Drawing in water from open reservoirs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher K 4.20 M + T 200 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info