Bedienungsanleitung Karcher K 5.91 MD PLUS (Seite 14 von 196) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78144

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

14 English

According to the applicable regula-

tions, the appliance must never be

used on the drinking water net

without a system separator. Use a

suitable system separator manufactured by

Kärcher; or, as an alternative, a system

separator as per EN 12729 Type BA.

For connection values, see type plate/tech-

nical data.

Observe regulations of water supplier.

Î Use a fibre-reinforced hose (not includ-

ed) with a standard coupling:

- Minimum diameter, 1/2 inches

(13 mm).

- Minimum length, 7.5 m.

Î Screw the coupling unit (supplied) to the

water connection on the appliance.

Î Push the water supply hose onto the

coupling unit, then connect it to the tap.

ṇ Caution

Never operate the high-pressure cleaner

when the tap is turned off as dry running will

damage the HP pump.

If the water supply is not clean, the Kärcher

water filter must be used (special accessory

- order No. 4.730-059).

When fitted with the appropriate accesso-

ries, this high-pressure cleaner can draw in

surface water, e.g. from water butts or

ponds (max. suction height 0.5 m).

Î Use the Kärcher water filter to protect

the HP pump and accessories (special

accessories). This filter removes dirt

from incoming water.

Î As the standard coupling system is not

suitable for use in suction mode, the

Kärcher suction hose with integrated fil-

ter should be used instead (special ac-

cessory) and suspended inside the

water butt.

Î Remove air from appliance before oper-

ation: Switch on the appliance when the

HP hose is not connected and run it until

the water which discharges from the HP

outlet is free of bubbles. Switch off ap-

pliance and connect HP hose.

Note: Fill suction hose with water before

use, this will help ventilate the pump of air.

Î Screw HP hose on to HP outlet on appli-

ance.

Î Push the appropriate spray lance on to

the trigger gun and fasten it by turning it

through 90°.

Î Open tap.

Î Plug in the main plug.

Î Set main switch to “I/ON”.

Î Press safety catch on the trigger gun to

release it and pull lever.

ṇ Risk of injury

The trigger gun is subjected to a recoil force

when the water jet is discharged. Make

sure that you have a firm footing and are

also holding the trigger gun and spray lance

firmly.

Carrying out the most common cleaning

tasks. The work pressure can be stageless-

ly regulated between "Min" and "Max".

Î Release the lever on the trigger gun.

Î Turn the spray lance to the desired po-

sition.

For strong contaminations.

Note

Detergent can only be added when the ap-

pliance is being operated in low pressure

mode.

All washing brushes supplied by Kärcher

are designed for use with detergents.

Î Use spray lance with pressure regula-

tion (Vario Power).

Turn the spray lance to "Mix" position -

low pressure.

Water supply

Water supply from mains

Water supply from open reservoirs

Start up

High pressure operation

Spray lance with pressure regulation

Spray lance with dirt blaster

Operation with detergent

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher K 5.91 MD PLUS Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info