Bedienungsanleitung Karcher K 7 Premium Power (Seite 12 von 138) (Alle Sprachen)

803262

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

12 English

Mounting the accessory net

1. Hang the accessory net on the hooks.

Illustration C

Push the high-pressure hose through the

hose guide

1. Insert the high-pressure hose through the hose

guide from the rear.

Illustration D

Installing the water connection coupling

1. Screw the water connection coupling onto the water

connection on the device.

Illustration E

Initial startup

Note

Take care not to exceed the maximum permissible

mains impedance at the connection point (see chapter

Technical data).

Contact your electricity supplier in the case of any un-

certainties regarding the mains grid impedance at your

electrical connection point.

1. Place the device on a flat and level surface.

2. For devices with a hose reel: Completely unwind the

high-pressure hose from the hose reel.

3. For devices without a hose reel: Unwind the high-

pressure hose completely and eliminate any loops

and twists.

4. Pull the high-pressure hose all the way forwards

through the hose guide.

5. Insert the high-pressure hose into the high-pressure

gun until it audibly latches into place.

Note

Take care to ensure the correct alignment of the nipple.

Illustration F

6. Check for a secure connection by pulling on the

high-pressure hose.

7. Plug the mains plug into a mains socket.

Water supply

For the connection values, see the type plate or chapter

Technical data.

Observe the water distribution company regulations.

ATTENTION

Damage through contaminated water

Contamination in the water can damage the pump and

the accessories.

KÄRCHER recommends using the KÄRCHER water fil-

ter for protection(special accessory, order number

4.730-059).

Connection to the water line

ATTENTION

Hose coupling with Aquastop on the water connec-

tion of the device

Damage to the pump

Never use a hose coupling with Aquastop on the water

connection of the device.

You can use an Aquastop coupling on the tap.

1. Plug the garden hose onto the water connection

coupling.

2. Connect the garden hose to the water line.

3. Open the water tap fully.

Illustration G

Sucking water from open containers

When used with the KÄRCHER suction hose with check

valve (special accessory, order number 2.643-100) this

high-pressure cleaner is suitable for sucking up surface

water, e.g. from rain barrels or ponds (for the maximum

suction height see chapter Technical data).

The water connection coupling is not required for vacu-

uming operation.

1. Fill the suction hose with water.

2. Screw the suction hose onto the device water con-

nection and hang it in a water source (e.g. water butt).

Vent the device

1. Switch the device on "I/ON".

2. Unlock the lever of the high-pressure gun.

3. Press the lever of the high-pressure gun.

The device switches on.

4. Allow the device for run a maximum of 2 minutes un-

til the water escaping from the high-pressure gun is

free of air bubbles.

5. Release the lever of the high-pressure gun.

6. Lock the lever of the high-pressure gun.

Operation

ATTENTION

Pump running dry

Damage to the device

If pressure does not build up in the device after 2 min-

utes then switch the device off and proceed according

to the instructions in chapter Troubleshooting guide.

High-pressure operation

ATTENTION

Damage to painted or sensitive surfaces

Surfaces can be damaged when the jet is too close to

the surface or an unsuitable spray lance is used.

Maintain a minimum spray distance of 30 cm when

cleaning painted surfaces.

Do not clean car tyres, paint or sensitive surfaces such

as wood with the dirt grinder.

1. Insert a spray lance into the high-pressure gun and

lock it by turning it 90°.

Illustration H

2. Switch the device on ("I/ON").

3. Unlock the lever of the high-pressure gun.

4. Press the lever of the high-pressure gun.

The device switches on.

5. Turn the Vario Power spray lance until the required

pressure level is shown on the pressure indicator.

Operation with detergent

DANGER

Failure to adhere to the safety data sheet

Incorrect handling of the detergent can seriously dam-

age your health

Observe the safety data sheet of the detergent manu-

facturer, in particular the instructions on personal pro-

tective equipment.

Note

Detergent can only be mixed into the jet at low pressure.

Note

A Plug ‘n’ Clean detergent bottle is required for operat-

ing with detergent. KÄRCHER detergent can be pur-

chased ready to use in a Plug ‘n’ Clean detergent bottle.

1. Remove the cover from the Plug ‘n’ Clean detergent

bottle.

2. Plug the detergent bottle into the Plug ‘n’ Clean de-

tergent connection with the opening facing down.

Illustration I

3. Use the Vario Power spray lance.

4. Turn the spray lance towards "MIX" until "MIX" is

displayed on the high-pressure gun.

The detergent solution is mixed with the water jet

during operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher K 7 Premium Power Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info