Bedienungsanleitung Karcher K 7 Smart Control (Seite 18 von 192) (Alle Sprachen)

803256

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

18 English

3. Press the separation button on the high-pressure

gun and disconnect the high-pressure hose from the

high-pressure gun.

ATTENTION

Damage to the high-pressure hose

Damage to the high-pressure hose through incorrect di-

rection of rotation

Observe the correct direction of rotation of the hose reel

when winding on the hose.

4. For devices with a hose reel: Use the crank handle

to turn the hose reel anticlockwise and coil up the

high-pressure hose.

5. For devices without a hose reel: Store the high-pres-

sure hose on the device.

6. Store the mains connection cable and accessories

on the device.

Observe the additional instructions before storing the

device for a longer period of time, see chapter Care and

service.

Frost protection

ATTENTION

Danger of frost

Incompletely emptied devices can be destroyed by

frost.

Completely empty the device and accessories.

Protect the device from frost.

The following requirements must be satisfied:

The device is disconnected from the water supply.

The high-pressure gun is disconnected from the

high-pressure hose.

1. Switch the device on "I/ON".

2. Wait for a maximum of 1 minute until no more water

escapes from the high-pressure hose.

3. Switch off the device.

4. Store the device in a frost-protected room, together

with all accessories.

Care and service

DANGER

Danger of electric shock

Injuries due to touching live parts

Switch off the device.

Remove the mains plug.

The device is maintenance-free, i.e. you do not need to

perform any maintenance work.

Clean the sieve in the water connection

ATTENTION

Damaged sieve in the water connection

Damage to the device through contaminated water

Check the sieve for damage before inserting it in the wa-

ter connection.

If necessary, clean the sieve in the water connection.

1. Remove the water connection coupling.

2. Pull the sieve out using flat pliers.

3. Clean the sieve under running water.

Illustration O

4. Insert the sieve into the water connection.

Replacing the batteries of

the high-pressure gun

Two non-rechargeable or rechargeable AAA batteries

are required.

The batteries are exhausted if nothing or a flashing bat-

tery symbol is visible in the display of the high-pressure

gun.

Illustration P

1. Press the locking slide.

Illustration Q

2. Open the battery compartment.

3. Remove the battery.

4. Insert new batteries, while paying attention to the

correct alignment of the poles.

5. Close the battery compartment.

6. Dispose of the used batteries in accordance with

statutory provisions.

Troubleshooting guide

Malfunctions often have simple causes that you can

remedy yourself using the following overview. When in

doubt, or in the case of malfunctions not mentioned

here, please contact your authorised Customer Service.

DANGER

Danger of electric shock

Injuries due to touching live parts

Switch off the device.

Remove the mains plug.

Device not running

1. Press the lever of the high-pressure gun.

The device switches on.

2. Check that the voltage specified on the type plate

corresponds to the voltage of the power source.

3. Check the mains connection cable for damage.

4. If the motor is overloaded and the motor circuit

breaker has triggered:

a Switch off the device "0/OFF".

b Allow the device to cool down for 1 hour.

c Switch the device on "I/ON" and resume opera-

tion.

Have the device checked by Customer Service if

this fault occurs repeatedly.

The device does not start up, the motor buzzes

Voltage drop due to a weak mains grid or when using an

extension cable

1. When switching on, first press the lever on the high-

pressure gun and then switch on the device "I/ON".

Device does not reach required pressure

The water supply is too low

1. Open the water tap fully.

2. Check the water inlet for an adequate flow rate.

The sieve in the water connection is dirty.

1. Pull the sieve in the water connection out using flat

pliers.

2. Clean the sieve under running water.

Air is in the device.

1. Vent the device:

a Switch on the device without a connected spray

lance for a maximum of 2 minutes.

b Press the high-pressure gun and wait until the

water escaping from the high-pressure gun is

free of air bubbles.

c Connect the spray lance.

d Observe the maximum suction height during suc-

tion operation (see chapter Technical data).

Strong pressure fluctuations

1. Clean the high-pressure nozzle:

a Use a needle to remove dirt from the nozzle drill.

b Rinse the high-pressure nozzle from the front

with water.

2. Check the water supply volume.

Device leaking

1. The device leaks a small amount for technical rea-

sons. If the leak is severe, request authorised Cus-

tomer Service.

Detergent is not sucked in

1. Turn the 3-in-1 Multi Jet spray lance to detergent

nozzle "MIX".

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher K 7 Smart Control Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info