Bedienungsanleitung Karcher K 7.260 (Seite 20 von 296) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

477974

Zoom out

Zoom in

Vorherige Seite

1/296

Nächste Seite

- 5

Illustration

Î Push the high pressure hose into the

trigger gun until it locks audibly.

Note: Make sure the connection nipple

is aligned correctly.

Check the secure connection by pulling

on the high-pressure hose.

ṇ Warning

According to the applicable regula-

tions, the appliance must never be

used on the drinking water supply

without a system separator. Use a

suitable system separator manufactured by

KÄRCHER; or, as an alternative, a system

separator as per EN 12729 Type BA. Water

flowing through a system separator is con-

sidered non-drinkable.

Note: Impurities in the water can damage

the high-pressure pump and accessories.

For protection, the use of the KÄRCHER

water filter (optional accessory, order no.

4.730-059) is recommended.

Observe regulations of water supplier.

For connection values, see type plate/tech-

nical data.

Î Use a fibre-reinforced water hose (not

included) with a standard coupling.

(Minimum diameter 1/2 inch (13 mm),

minimum length 7.5 m).

Illustration

Î Screw the coupling element (supplied)

to the water connection on the appli-

ance.

Push the water supply hose onto the

coupling unit, then connect it to the wa-

ter supply.

This high-pressure cleaner is suited to work

with the KÄRCHER suction hose with back-

flow valve (Optional accessory, order no.

4.440-238) to draw in surface water, e.g.

from water butts or ponds (see specifica-

tions for max. suction height).

Î Fill the KÄRCHER suction hose with

backflow valve with water, screw to wa-

ter supply and hang into the water butt.

Î Appliance ventilation: Switch the appli-

ance on with the high-pressure hose

detached and operate (max. 2 minutes)

until the water exits the high-pressure

connection without bubbles. Switch off

appliance and reconnect high-pressure

hose.

Caution

Dry runs lasting longer than two minutes

lead to damages to the high pressure

pump. If the appliance does not build up

pressure within two minutes, switch it off

and proceed as instructed in the Chapter

"Troubleshooting".

Illustration

Î Insert the high pressure hose tightly into

the quick coupling on the appliance, it

will lock in audibly.

Note: Make sure the connection nipple

is aligned correctly.

Check the secure connection by pulling

on the high-pressure hose.

Illustration

Î Push the spray lance into the trigger

gun and fasten it by turning it through

90°.

Î Completely open the water tap.

Î Insert the mains plug into the socket.

Î Turn on the appliance “I/ON”.

Connect the high pressure hose to the

hand spray gun

Water supply

Water supply from mains

Drawing in water from open reservoirs

Start up

20 EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher K 7.260 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info