Bedienungsanleitung Karcher PCL4 (Seite 13 von 156) (Alle Sprachen)

724918

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

English 13

Installation

Note

The handle is installed only once. The handle halves

may not be separated again after installation. Take care

to ensure that the water hose and the mains cable are

not crushed during installation.

1. Plug the handle sections together. The pipe latches

audibly into place.

Illustration B

2. Press the water hose and then the mains cable into

the cable channel from the top to the bottom (start-

ing at the hand grip).

Illustration C

3. Press any protruding cable and water hose firmly in-

to the brush head casing.

Illustration D

The mains cable and water hose must not protrude out

of the device during operation!

Initial startup

1. Close the water volume regulation valve.

Illustration H

2. Connect the water hose to the device. The coupling

must audibly engage.

3. Secure the water hose to the hand grip using Velcro

tape to provide strain relief.

Illustration E

4. Connect the water hose to the water tap and open

the water tap. Please observe the maximum water

pressure (see "Technical data").

5. Connect the mains cable to a suitable extension ca-

ble labelled as conforming to protection class IPX4.

Please be sure to observe the safety instructions.

Operation

Correct handling of the brushes

Note

Use only the brushes suitable for the surface to be

cleaned.

Observe the following instructions for correct use of the

brushes.

1. Position the brushes evenly on the surface to be

cleaned.

Illustration F

2. Guide the brushes over the surface with light pres-

sure.

Switching on the device

Note

You must unlock the power switch in order to start the

device. The specified sequence must be adhered to

1. Press the unlocking button.

Illustration G

2. Press the power switch.

The device starts up.

3. Release the power switch.

The device stops.

Water volume regulation valve

Note

The volume of water emitted by the device through the

nozzles can be adjusted using the water volume regula-

tion valve to suit the cleaning task.

1. Pull the valve lever backwards to increase the water

volume.

2. Push the valve lever forwards to decrease the water

volume or close the valve completely.

Illustration H

Cleaning wooden surfaces

Use the brush for wooden floor coatings for cleaning

wooden surfaces.

Note

Test the device on an inconspicuous area before us-

ing on sensitive surfaces, e. g. wood.

Do not allow it to remain in one area, but keep it in

motion.

Note

Always clean wooden surfaces in the direction of the

grain. Always clean along the floorboards or wooden el-

ements and down the slope.

Note

Pre-treatments may be removed from pre-treated sur-

faces. Uneven light-dark effects result from the type of

wood or its treatment. It is a desirable result to remove

the film on weathered wooden surfaces.

1. Guide the device slowly over the surface.

Illustration I

Apply a suitable care agent or preservative after

cleaning for optimum results!

Cleaning stone surfaces

Use the brush for stone coverings for cleaning stone

surfaces in outside areas (not included in the scope of

delivery - see the Accessories and spare parts chapter

for sources).

Note

Remove any loose elements such as gravel before

cleaning.

1. Guide the device slowly over the surface.

Storing the device

Illustration J

The device can be stored hanging on a wall hook. You

can also alternatively place the device on the parking

edge of the spray guard. Take care to ensure that the

device does not stand on the brushes to prevent dam-

age to the bristles.

1. Disconnect the connections.

2. Empty the device (see "Frost protection").

3. Clean the device (see "Cleaning").

Transport

몇CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during transporta-

tion.

Storage

몇CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during storage.

Frost protection

ATTENTION

Danger of frost

Incompletely emptied devices can be destroyed by

frost.

Completely empty the device and accessories.

Protect the device from frost.

1. Store the device in a frost-protected place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher PCL4 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info