Bedienungsanleitung Karcher SC 3 Deluxe EasyFix Premium (Seite 15 von 188) (Alle Sprachen)

803424

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

English 15

Carpet glider

The carpet glider is used for freshening up carpets.

ATTENTION

Beware of damaging the carpet glider and carpet

Contamination on the carpet glider, as well as heat and

moisture penetration, can result in the carpet being

damaged.

Prior to the application, also check the heat resistance

and impact of steam on the carpet at an insignificant

spot using as small an amount of steam as possible.

Observe the cleaning instructions from the carpet man-

ufacturer.

Prior to using the carpet glider, make sure that the car-

pet has been vacuumed and that stains have been re-

moved.

Prior to application and following operating pauses, re-

move any possible water accumulation (condensate) in

the appliance by means of evaporating the condensate

into a drain (without floor cleaning cloth / with accesso-

ries).

Only use the carpet glider with a floor cleaning cloth on

the floor nozzle.

Steam clean with a weak steam stage when using the

carpet glider.

In order to prevent too much moistening and to avoid

the risk of damage due to temperature effects, do not di-

rect the steam continuously onto one spot (maximum

5 seconds).

Do not use the carpet glider on deep-pile carpets.

Fastening the carpet glider to the floor nozzle

1. For fastening the floor cleaning cloth to the floor

nozzle, please refer to chapter Floor nozzle.

Illustration Q

2. Using a little force, allow the floor nozzle to slide into

the carpet glider and engage there.

Illustration R

3. Start cleaning the carpet.

Removing the carpet glider from the floor nozzle

몇CAUTION

Beware of burns to your feet

The carpet glider can heat up during the steaming pro-

cess.

Do not operate or remove the carpet glider bare-footed

or using open sandals.

Only operate or remove the carpet glider using suitable

footwear.

1. Press the strap on the carpet glider downwards us-

ing your toecap.

2. Lift the floor nozzle upwards.

Illustration R

Care and service

Draining the water reservoir

ATTENTION

Device damage due to water putrefaction

If the device is not put into operation for more than 2

months, the water in the reservoir may putrefy.

Drain the water reservoir before breaks in operation.

1. Press the On/Off switch.

The device has been switched off.

2. Pull the mains plug out of the socket.

3. Remove the accessories from the accessory hold-

ers.

4. Remove the decalcification cartridge from the de-

vice.

5. Drain the water reservoir.

Illustration S

Replacing the decalcification cartridge

ATTENTION

Device damage and shortened service life

If the replacement intervals (indicator light) for the de-

calcification cartridge are not observed, there is a risk of

device damage and the service life of the device may be

shortened.

Observe the replacement intervals (indicator light).

Note

The replacement intervals depends on the local water

hardness. Areas with hard water (e.g. III/IV) have a

higher replacement interval than areas with soft water

(e.g. I/II).

Indicator lamp at end of the run time

The "decalcification cartridge indicator light " indicates

when the decalcification cartridge has to be replaced:

●The indicator light flashes 2 hours before the run

time expires.

●The indicator light flashes more quickly 1 hour be-

fore the run time expires.

●Once the run time for the decalcification cartridge

has expired, the indicator light and the LED strip

light lights up in continuously red and the pump

switches off automatically in order to prevent device

damage.

Inserting the decalcification cartridge

ATTENTION

Device damage

There is a risk of damage to the device if the used de-

calcification cartridge is re-used.

Work carefully in order to prevent mixing up the cartridg-

es.

Note

When steaming for the first time after removing and re-

inserting the decalcification cartridge, the steam jet may

be weak or irregular, and individual drops of water may

be expelled. The device requires a short running-in pe-

riod in which the decalcification cartridge fills with water.

The steam volume that is expelled increases constantly

until the maximum steam volume has been reached af-

ter approx. 30 seconds.

1. Press the Off switch.

The device has been switched off.

2. Remove the decalcification cartridge.

3. Insert the new decalcification cartridge.

4. Press the On switch.

The device is switched on.

5. Press and hold the Maximum steam volume and

Reduced steam volume buttons at the same time

until the "Replace decalcification cartridge" goes

out. This means that the reset is complete.

6. Allow the device to heat up.

7. Press and hold the steam lever for approx. 30 sec-

onds to vent the decalcification cartridge.

Setting the water hardness

ATTENTION

Device damage due to calcification

Without a decalcification cartridge, the device may cal-

cify if the water hardness is set incorrectly.

Always work with a decalcification cartridge.

Set the device to the local water hardness.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher SC 3 Deluxe EasyFix Premium Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info