Bedienungsanleitung Karcher SP 22.000 Dirt Level Sensor (Seite 13 von 164) (Alle Sprachen)

803804

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

English 13

Technical data

Subject to technical modifications.

Optimising the flow rate

The flow rate is further increased:

●The lifting height is reduced.

●The diameter of the hose used is increased.

●The length of the hose used is decreased.

●The smaller the pressure loss caused by the con-

nected up accessories.

Declaration of Conformity

We hereby declare that the machine described below

complies with the relevant basic safety and health re-

quirements in the EU Directives, both in its basic design

The pump does not start

up, or stops suddenly

during operation

The power supply is disconnected. 1. Check the fuses and the electrical connec-

tions.

The thermal protection switch has

switched off the pump because of over-

heating.

1. Pull the mains plug out of the socket.

2. Allow the pump to cool down.

3. Remove any dirt particles in the suction ar-

ea.

4. Clean the suction area.

5. Prevent the pump from running dry.

Dirt particles block the suction area. 1. Pull the mains plug out of the socket.

2. Clean the suction area.

The level sensor stops the pump. 1. Check the position of the level sensor and

correct if necessary.

Note

The pump stops 15 s after the level sensor no

longer has contact with the water.

The level sensor does not react because

it is soiled.

1. Clean the level sensor.

The pumping capacity

decreases

The suction area is clogged. 1. Pull the mains plug out of the socket.

2. Clean the suction area.

The delivery rate is too

low

The maximum delivery head is exceed-

ed.

The hose diameter and the hose length

have been selected incorrectly.

1. Observe the maximum delivery head, see

chapter Technical data.

2. If necessary, select a greater hose diame-

ter or a shorter hose length, see chapter

Optimising the flow rate.

Quick-Connect cannot

be opened or closed

The push-fit system is dirty. 1. Remove the clip.

2. Clean the clip.

3. Install the clip.

The pump runs although

the level sensor has no

contact with the water

The level sensor does not react because

it is soiled.

1. Clean the level sensor.

The switch is set to Manual mode (MAN). 1. Set the switch ´to Automatic mode (AUTO).

Extended after-running

time

The level sensor is dirty. 1. Clean the level sensor.

Fault Cause Rectification

SP 17.000

Flat Level

Sensor

SP 22.000

Dirt Lev-

el Sensor

Device performance data

Mains voltage V 230-240 230-240

Power frequency Hz 50 50

Nominal power W 550 750

Maximum flow rate l/h 17,000 22,000

Pressure (max.) MPa

(bar)

0.09

(0.9)

0.08

(0.8)

Delivery height (max.) m 9 8

Immersion depth

(max.)

m7 7

Perm. temp. feed fluid °C 5...35 5...35

Particle size (max.) of

permissible feed fluids

mm 5 30

Minimum fluid level

(manual mode)

mm 7 50

Residual fluid height mm 1 35

Weight (without acces-

sories)

kg 6 6.7

EU Declaration of Conformity

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Karcher SP 22.000 Dirt Level Sensor Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info